查询词典 tic-tac-toe

OM and SEM results show that rodlike TiB whiskers and equiaxed TiC particulates distribute uniformly in titanium matrix.

OM与SEM分析表明复合材料中存在棒状TiB晶须和近似等轴状TiC颗粒两种不同形态的增强体，并且两种增强种体均匀的分布在基体中。

The effect of TiC coating in electrode tip surface on spheriform electrode degradation during resistance spot welding zinc coated steel was investigated by SEM,EDX and XRD.

利用SEM、EDX和XRD等方法分析了在点焊镀锌钢板时球形电极表面熔敷TiC涂层对电极失效的影响。

The studied results on abrasive behavior of 〓/ZA-12 composite indicate thatthe abrasive properties are improved significantly by addition of TiC particles underdry sliding.

在本研究范围内，TiC颗粒含量越高，〓/ZA-12复合材料的摩擦磨损性能越好。

The synthesized uniphase C with TiC: WC=5: 5 has been synthesized successfully for the first time under the condition determined by this study.

根据研究所确定的条件第一次成功地合成了TiC：WC=5：5的单相C粉末，其粒径为0.6-2μm。

The results show that high energy ball milling refines and homogenizes the mixed powders, accelerates the sintering process, and with the increase of milling time, the grain is finer and the alloy is denser. HIP and forging is beneficial to decrease or remove the pole formed during the sinter course, and as the last process, forging breaks the junctions between TiC particles, the microstructure and mechanical properties of alloy are improved.

研究结果表明：高能球磨使粉末细化和成分均匀化，促进烧结进程，随球磨时间的延长，合金组织细化且致密；热等静压和锻造工艺可进一步减小和消除合金中烧结后残留的孔洞等缺陷；锻造作为最后工艺，可使TiC颗粒之间的连接破碎，促使硬质相颗粒弥散分布，从而改善烧结组织，提高合金的致密性及力学性能。

The interface lattice misfitting theory cannot be used to explain that ZrC, TiC, TiN, as catalyzer, are better than TiO during heterogeneous nucleation of Au liquid.

异质形核是凝固领域的核心问题之一，界面共格对应理论无法解释金液滴异质形核过程中ZrC，TiC，TiN等基底的触媒作用优于TiO的现象。

The interface lattice misfitting theory can not explain that TiC and CaS act as an efficient catalyzer during the non-equilibrium solidification of austenite steel .

利用界面共格对应理论无法解释奥氏体钢非平衡凝固过程中TiC、CaS为奥氏体枝晶有效异质核心的现象。

The dissolving mechanism of Al/TiC prefabricating alloy in Zinc melt has been analyzed.

对Al/TiC预制合金在锌熔体中的溶解机理进行了分析。

The dissolving mechanism of Al/TiC prefabricating alloy in Zinc melt has been analyzed.

摘 要：对Al/TiC预制合金在锌熔体中的溶解机理进行了分析。

Stress concentration zones and the maximum value of thermal stress of the TiC cermet/iron joint brazed with Ag-Cu-Zn filler metal during cooling were studied in this paper.

本文研究了采用Ag-Cu-Zn钎料在1173K温度下钎焊TiC金属陶瓷与铸铁挺柱实际件时，在冷却过程中接头处的应力集中区和热应力最大值。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新