查询词典 tic-tac-toe

Ferrotitanium , nickel and sucrose to carbonize the sucrose. TiC/ Fe-Ni composite coatings were prepared by plasma spraying of the Ti-Fe-Ni-C composite powder .

以 TiFe粉、Ni粉和蔗糖为原料，通过蔗糖的热分解碳化制备 Ti-Fe-Ni-C系反应热喷涂复合粉末，并利用等离子喷涂制备了 TiC/ Fe-Ni复合涂层。

The effect of TiB〓 on the microstructure and properties of TiC-based cermet was studied.

研究了TiB〓替代TiN后对TiC基金属陶瓷组织和性能的影响。

The results indicate that in Ti-6Al-1.8C the TiC has two different morphologies, dendrite and short bar-like.

结果表明：Ti-6Al-1.8C合金中TiC的形态有树枝状晶和短棒状两种形态。

The influences of thicknesses of the TiC interface layer and diamond coating on the field emission properties are primarily explored and the ideal combination of annealing temperature and coating thickness is decided.

本文重点探索了TiC界面层厚度和金刚石涂层厚度对场发射性能的影响，分析比较了不同热处理温度和不同涂层厚度样品的场发射性能，确定出较为理想的退火温度与金刚石涂层厚度的参数组合。

After this the dissolvent velocity of Al/TiC prefabricating alloy in zinc melt has been measured by means of self-made experimental equipment.

利用自制的试验装置测试了Al/TiC预制合金在锌熔体中的溶解量。

TiC/Cr19Al3 steel bonded carbides were prepared by in-situ synthesis taking ferrotitanium, ferrochromium, iron, carbon powders as raw material, and the microstructure of the steel bonded carbides was analyzed.

以钛铁粉、铬铁粉、铁粉、胶体石墨等为原料，原位反应生成TiC/Cr19Al3钢结硬质合金，并对所制备的试样进行组织结构分析。

Using ferrotitanium, carbon and iron powder as staring materials, TiC-Fe composite coatings were synthesized and deposited by RFS.

本文采用钛铁粉、石墨粉、铁粉为主要原料，成功制备了TiC-Fe复合涂层，并研究了喷涂过程中的反应历程。

The f ormation mechanism is self-propagate reacive synthesis conducted by mechanical alloying is 5.641 μm, and crystalline grain of TiC is 10 nm. The high energy ba ll miling is the most ball milling in those millings. The process of nanocrystal line TiC fabricated is occurred at room temperature.

比较三种球磨机，高能式球磨机效率最高，应用高能式反应球磨可以得到颗粒平均大小为5.641 nm，并且具有10 nm左右的纳米晶粒的TiC，通过球磨工艺可以使该反应过程在室温进行。

In order to improve the life of spot-welding electrode for zinc-coated steel, electrospark deposition processes were studied taking TiC as fusing material and CrZrCu as spot-welding electrode.

为了改善镀锌钢板点焊电极的寿命，选用铬锆铜球型点焊电极，以TiC作为熔敷材料，进行了点焊电极表面电火花沉积 TiC工艺试验。

The results show that, in the process of preparing TiC-Al2O3-20Fe cermet by SHS/PHIP, the release of gases and the existence of the liquid are the important factors. The products consist of TiC and Al2O3 particles and quasi-continuous Fe-binder phase.

结果表明，燃烧合成过程中气体的排放和液相的存在是合成密实材料的关键，通过优化工艺合成了密实度为97.7％的TiC-Al2O3-20Fe金属陶瓷。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新