查询词典 thermo-shield

Hot Steel H13; Thermo-Chemical Heat Treatment ; High Energy Density Surface Treatment

H13模具钢；表面化学热处理；高能束表面处理

The first shoe created for professional alpinists with a single moulded structure injected with various thermo-plastic materials.

第一双用于专业登山鞋类，采用单模结构并用多种热塑材料注塑而成。

Thermo-bonded polyester battings are low energy consumption and no pollution.

涤纶热熔絮片具有能耗低、无污染的特点。

Then, by analysis of heat transfer mechanism of clothing insulation materials, thermo-bonded polyester battings consisted of fine-denier fibers and hollow fibers are trial-produced.

通过对絮料传热机理的分析，明确了絮片的设计思路。

In course of trial-producing thermo-bonded polyester battings, firstly, the mass fraction of hollow polyester fibers is determined by analysing test results to insure the battings' compression elasticity.

论文在细旦涤纶／中空涤纶复合絮片的试制过程中，首先在保证絮片压缩回弹性较好的前提下，通过分析测试结果，确定中空涤纶的含量应该在40％左右。

The results show that the best sintering process for SiC preform is 1100℃, 8 h in vacuum, by which the open porosity is 99.6% and the preform strength reaches 0.57MPa. The thermo-physical characteristics of 57% SiC/Al composites produced by this technique are as follows: the relative density is 98.7%; the thermal expansion coefficient is 7.5×10^(-6)℃^(-1) which almost matches those of GaAs and BeO; the thermal conductivity is 1.65×10^5W/K, which corresponds to that of Cu(15%)/W and decuples that of Kovar alloy; the density is close to that of aluminum and less than that of one fifth of Cu/W.

结果表明：经1100℃真空烧结8h的SiC预成形坯开孔率可以达到99.6%，抗压强度为0.57MPa；所制备的57%SiC/Al复合材料相对密度为98.7%，热膨胀系数为7.5×10^(-6)℃^(-1)，与GaAs、BeO的接近，热导率为1.65×10^5W/K，与传统Cu(l5%)/W相当，是柯伐合金的10倍，在密度上接近Al，不到Cu/W的1/5。

The results show that the best sintering process for SiC preform is 1100℃, 8 h in vacuum, by which the open porosity is 99.6% and the preform strength reaches 0.57 MPa. The thermo-physical characteristics of 57% SiCp/Al composites produced by this technique are as follows: the relative density is 98.7%; the thermal expansion coefficient is 7.5×10-6 ℃-1 which almost matches those of GaAs and BeO; the thermal conductivity is 1.65×105 W/K, which corresponds to that of Cu(15%)/W and decuples that of Kovar alloy; the density is close to that of aluminum and less than that of one fifth of Cu/W.

结果表明：经1 100 ℃真空烧结8 h的SiC预成形坯开孔率可以达到99.6%，抗压强度为0.57 MPa；所制备的57％SiCp/Al复合材料相对密度为98.7％，热膨胀系数为7.5×10-6 ℃-1，与GaAs、 BeO的接近，热导率为1.65×105 W/K，与传统Cu(15%)/W相当，是柯伐合金的10倍，在密度上接近Al，不到Cu/W的1/5。

Development and application of thermo reactors dominants at present and will do so in a long time to come, while technology research on fast reactors and fusion will be carried on concurrently.

发展与热核反应堆目前优势种申请，并会做很长的时间来临时，而对快堆技术和融合的研究将同时进行。

The thermo electrets of PMMA with surface potentials between about 50 and 〓 were fabricated.

采用热电极化的方法制得驻极电压在50～〓V正负电位的圆片状驻极体型聚合物聚甲基丙烯酸甲酯。

The curve of expansion versus temper- rature in the temperature elevating process is depicted automatically and the coefficients of mean lin- ear expansion, instantaneous thermo-expansion, transforming temperature and softing point can be printed according to the.

本文介绍了一种■全由计算机进行设定控制的热膨胀仪，可以对温度范围、升温速率、初始条件进行设定，并由计算机完成实时数据的采集及处理，完成升温过程中温度-伸长量曲线自动描绘，并根据用户要求自动打印出各温度段的平均线膨胀系数、瞬间热膨胀转变温度及软化点等，其结构准确可靠、使用方便、自动化程度高，达到国内领先水平。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。