查询词典 thermo-anesthesia

Even in aerobic activity the thermo-formed and ergonomically adjusted contact surfaces enable the free flow of air on the back.

即使在有氧运动的热形成和变化，符合人体工程学的接触面，使空气在背面自由流通。

In order to analyze the relationship between radiation heat transfer and thermo-efficiency, the radiant heat flux of the cylinder and thermal balance are measured. The results show that: The reduction of thermal radiant flux in the cylinder is the primary cause of the improvement of thermal efficiency of the engine.

为了研究发动机热效率和辐射传热量变化之间的关系，利用辐射传感器测量了柴油机燃用DMC柴油混合燃料后缸内辐射传热量，进行了热平衡实验，分析结果表明，添加含氧燃料后，发动机缸内辐射传热量的减少是导致其有效热效率的提高的主要原因。

In thesetwo models some theories and methods are adopted from thermo-dynamics,micrometeorology,plant physiology,hydrology,and otherscience fields.

它们依据能量平衡和水量平衡原理，引进了大气热力学、微气象学、植物生理学等学科的某些理论和方法。

Thermo-mechanical fatigue failure of the packaging materials is one of the main causes for the microelectronic component failure.

封装材料的热疲劳失效是封装器件失效的主要原因之一。

The results show that the plasticity zone and dynamically quiescent layer become fine equiaxed recrystallisation under the thermo-mechanical effect, the grains in the heat-affected zone grow up because of the effect of friction heat. When the rotation speed is 2 500 r/min and the welding time is 12 s, good joint is achieved, and the tensile shear strength of the joint reaches 9.24 kN. The tensile shear strength of spot increases with increasing tool rotation speed, with increasing welding time, the strength increases first, while then reduces. The microhardness of plasticity zone is high, but is slightly lower than that of the base metal, the minimum value of microhardness is in the heat affected zone. When the energy input of joint is high, the fracture type of spot is mode Ⅰ, and the tensile shear strength is high; on the contrary, when the energy input of joint is less the fracture type of spot is mode Ⅱ, and the strength is low.

结果表明：塑性区和动态静止层的晶粒在热和力作用下发生动态再结晶形成细小的等轴晶，热影响区的晶粒在摩擦热作用下长大变粗；搅拌头旋转速度为2 500 r/min，焊接时间为12 s时，可以获得力学性能较好的焊点，焊点的剪切强度达到9.24 kN；焊点的剪切强度随搅拌头旋转速度的增大而增大，随焊接时间的延长先增大后减小；塑性区的显微硬度较高，但略小于母材，接头显微硬度的最小值分布在热影响区；焊点热输入量较多时，接头为Ⅰ型断裂，焊点的剪切强度较高；焊点热输入量较少时，接头为Ⅱ型断裂，焊点的强度较低。

Because of the thermo-protection of osmolytes, the refolding of eMDH at a higher temperature (15℃) was achieved.

另外，利用渗透剂对蛋白质的热保护作用，实现了在较高温度（15℃）下eMDH包含体的复性。

The oxidation of high speed steel was studied at 500 ℃, 650 ℃ and 800 ℃ in the air, and the isothermal oxidation kinetics curves were obtained by thermo gravimetric analysis.

借助热重分析仪研究了高速钢轧辊工作层材料在500 ℃、650 ℃、800 ℃下于空气中的恒温氧化行为，得到了高速钢在不同温度下的恒温氧化动力学曲线。

By dipping in sodium chloride solution, heat-resistant experiment, salt spray test and thermo gravimetric analysis, it can be concluded that this coating has high decomposition temperature.

通过红外光谱和交流阻抗分析了在不同温度使用条件下对涂层成分和阻抗值的影响，表明该涂层能长期耐200℃的高温，而且具有良好的耐热耐蚀性。

The structure of the copolymer was characterized by infrared spectrum, glass transition temperature and maximal heat decomposition temperature were analyzed by different scanning calorimetry and thermo gravimetric analysis.

利用红外光谱表征了共聚物结构，利用差示扫描量热法和热重分析测试了共聚物的玻璃化转变温度和最大热分解温度。

China's nuclear energy application, like in many other countries, develops in "three steps"(i.e., from thermo neutron reactors to fast neutron breeding reactors and then to controlled fusion reactors).

中国的核能源的应用，在许多其他国家一样，发展的&三步走&（即从热中子反应堆快中子反应堆繁殖，然后再受控核聚变反应堆）。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。