查询词典 thermo-anesthesia

Hot Steel H13; Thermo-Chemical Heat Treatment ; High Energy Density Surface Treatment

H13模具钢；表面化学热处理；高能束表面处理

The first shoe created for professional alpinists with a single moulded structure injected with various thermo-plastic materials.

第一双用于专业登山鞋类，采用单模结构并用多种热塑材料注塑而成。

Thermo-bonded polyester battings are low energy consumption and no pollution.

涤纶热熔絮片具有能耗低、无污染的特点。

Then, by analysis of heat transfer mechanism of clothing insulation materials, thermo-bonded polyester battings consisted of fine-denier fibers and hollow fibers are trial-produced.

通过对絮料传热机理的分析，明确了絮片的设计思路。

In course of trial-producing thermo-bonded polyester battings, firstly, the mass fraction of hollow polyester fibers is determined by analysing test results to insure the battings' compression elasticity.

论文在细旦涤纶／中空涤纶复合絮片的试制过程中，首先在保证絮片压缩回弹性较好的前提下，通过分析测试结果，确定中空涤纶的含量应该在40％左右。

The results show that the best sintering process for SiC preform is 1100℃, 8 h in vacuum, by which the open porosity is 99.6% and the preform strength reaches 0.57MPa. The thermo-physical characteristics of 57% SiC/Al composites produced by this technique are as follows: the relative density is 98.7%; the thermal expansion coefficient is 7.5×10^(-6)℃^(-1) which almost matches those of GaAs and BeO; the thermal conductivity is 1.65×10^5W/K, which corresponds to that of Cu(15%)/W and decuples that of Kovar alloy; the density is close to that of aluminum and less than that of one fifth of Cu/W.

结果表明：经1100℃真空烧结8h的SiC预成形坯开孔率可以达到99.6%，抗压强度为0.57MPa；所制备的57%SiC/Al复合材料相对密度为98.7%，热膨胀系数为7.5×10^(-6)℃^(-1)，与GaAs、BeO的接近，热导率为1.65×10^5W/K，与传统Cu(l5%)/W相当，是柯伐合金的10倍，在密度上接近Al，不到Cu/W的1/5。

The results show that the best sintering process for SiC preform is 1100℃, 8 h in vacuum, by which the open porosity is 99.6% and the preform strength reaches 0.57 MPa. The thermo-physical characteristics of 57% SiCp/Al composites produced by this technique are as follows: the relative density is 98.7%; the thermal expansion coefficient is 7.5×10-6 ℃-1 which almost matches those of GaAs and BeO; the thermal conductivity is 1.65×105 W/K, which corresponds to that of Cu(15%)/W and decuples that of Kovar alloy; the density is close to that of aluminum and less than that of one fifth of Cu/W.

结果表明：经1 100 ℃真空烧结8 h的SiC预成形坯开孔率可以达到99.6%，抗压强度为0.57 MPa；所制备的57％SiCp/Al复合材料相对密度为98.7％，热膨胀系数为7.5×10-6 ℃-1，与GaAs、 BeO的接近，热导率为1.65×105 W/K，与传统Cu(15%)/W相当，是柯伐合金的10倍，在密度上接近Al，不到Cu/W的1/5。

Development and application of thermo reactors dominants at present and will do so in a long time to come, while technology research on fast reactors and fusion will be carried on concurrently.

发展与热核反应堆目前优势种申请，并会做很长的时间来临时，而对快堆技术和融合的研究将同时进行。

The thermo electrets of PMMA with surface potentials between about 50 and 〓 were fabricated.

采用热电极化的方法制得驻极电压在50～〓V正负电位的圆片状驻极体型聚合物聚甲基丙烯酸甲酯。

The curve of expansion versus temper- rature in the temperature elevating process is depicted automatically and the coefficients of mean lin- ear expansion, instantaneous thermo-expansion, transforming temperature and softing point can be printed according to the.

本文介绍了一种■全由计算机进行设定控制的热膨胀仪，可以对温度范围、升温速率、初始条件进行设定，并由计算机完成实时数据的采集及处理，完成升温过程中温度-伸长量曲线自动描绘，并根据用户要求自动打印出各温度段的平均线膨胀系数、瞬间热膨胀转变温度及软化点等，其结构准确可靠、使用方便、自动化程度高，达到国内领先水平。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。