查询词典 thermo-algesia

The analytic studies of the MITA procedure based on dynamics and the function of thermo-diffuse and thermo-conduction combine these three physic field systematically. Compared with situation function with thermo-balance method, the analytic studies based on dynamics have less parameters approximation, and more precision. Meanwhile, the discipline of the microwave energy absorbed by tissue is should studied also.

基于动力学和热扩散、传导方程的微波热致超声波机制解析解的分析，将上述三类物理场有机地结合在了一起，与基于热平衡的状态解析分析相比，这一方法更少地对三物理场所涉及的参数进行近似，能更准确地反映微波热致超声波机制。

By means of thermo—elastic-plastic finitive element method, the thermo—mechanical loading chart of the ingot mould in working cycle is obtained; with this chart as a control factor, multicycle experiment is carried out on a thermo—mechanical simulater, resembling the circumstance of the real working condition.

即用热弹塑性有限元法获得钢锭模一个使用周期内的热—力载荷谱，在热力模拟实验机上用该热—力载荷谱控制进行多周期模拟实验分析。

3D-CTM (Coupled Thermo-Mechanical Forming Simulation) software for precision forging process of aero-engine blade was developed. The key technologies of 3D coupled rigid-viscoplastic thermo-mechanical FEM simulation of blade forging process were studied systematically. By using the remeshing method of contracting from the boundary to the inner, new mesh system from old distorted mesh system can be obtained. A method of modifying the position of nodes touching on the die according to its original normal was proposed to avoid "dead lock" problem due to uncontinuity of normal of scatted die meshes. The pseudo-static iterative algorithm was used to simplify the coupled thermo-mechanical computation. In particular, formulations to determine relaxation factor β was established for rigid viscoplastic FEM adopting penalty function method, and an improved cubic factor rapid algorithm derived from these formulations was proposed by combining with the advantage of advance and retreat search method.

采用基于边界构形的内缩法，实现了三维畸变网格的重新划分；提出了初矢修正法对触模节点的位置进行修正，解决了由于离散的模具网格的法矢不连续造成的&死锁&问题；采用准静态迭代法简化了速度场和温度场耦合计算过程；特别是针对减速因子β的选取，建立了适用于三维复杂成形过程刚粘塑性罚函数法有限元三次因子法的计算公式，并结合进退搜索法提出了改进的三次因子快速算法，提高了模拟计算效率和稳定性，在此基础之上，开发了面向叶片精锻过程的三维刚粘塑性热力耦合有限元模拟分析系统(3D-CTM)，系统的可靠性得到了圆柱体镦粗的验证。

In this paper,a three-dimension finite element calculating model for thermo-stress coupling analysis is developed with the finite element software package ANSYS and is used to calculate the practical thermo-stress distribution in the supporting nozzle plane board.

文中利用ANSYS有限元分析软件建立了铸嘴支撑面板温度-应力耦合分析的三维有限元计算模型，并对实际工况下面板的热应力分布进行了计算。

The present experimental study investigated the mechanism of the self-exciting thermo-acoustic oscillation and the forced thermo-acoustic oscillation.

通过实验，揭示了热声自激振动与热声强制振动现象发生的条件与机理，研究了热声发动机的关键部件——板叠的形状与材质对系统的起振温度的影响。

Thermo Electron Instruments Co., Ltd. is the manufacturing centre of Thermo Electron Corporation in China.

热电仪器有限公司是美国热电集团在中国上海的制造中心。

The aim of this research was based on enhancing the anaerobic digestion efficiency of straw by thermo-alkaline pretreatment in which mainly studied the effect of thermo-alkaline pretreatment on solubility of straw. And then the straw after pretreatment was anaerobically digested to verify effects of pretreatment on anaerobic digestion of straw.

本研究以提高秸秆厌氧发酵效率为目的，采用热碱预处理方法对秸秆进行预处理，研究预处理温度、碱用量对秸秆可溶性的影响，将预处理后的秸秆用于厌氧发酵，检测其对厌氧发酵结果的影响。

Also introduced by Thermo at ASMS was the Exactive benchtop LC/ MS system, which is based around the Orbitrap mass analyzer, in contrast to Thermo's LTQ-Orbitrap and LTQ-FT, the Exactive is not a tandem system, which greatly lowers its price, but it can still provide MS/MS.

Thermo还推出了台式的包含Orbitrap分析器的Exactive仪器，因为它不是串联的仪器，所以大幅降低了价格，但其实，Exactive仍可以提供串联质谱MS/MS功能。

In this paper, based on the knowledge about the change in the microstructures and mechaniacal properties of the cast irons with the influence of temperature, stress and thermo—mechanical circulated load in working cycle of ingot mould, the temperature and stress fields have been analysed by means of thermo-elastic-plastic finitive element, and futher, the behavior of thermal stress factors in every working cycle of the mould have been investigated, by which principles for optimum design of ingot mould's structure has been put out.

本文以钢锭模一个使用周期内的温度场、应力场及热一力循环载荷作用下铸铁的组织结构和力学性能的变化规律为基础。利用热弹塑性有限元法对钢锭模使用过程中的温度场及应力场进行了分析，并进一步研究了钢锭模在每个使用周期间的热应力参数的变化规律，提出了钢锭模结构优化设计的基本原则。

The results indicated that the thermo-stability of the polymers derived from BOEMA was not as good as those derived from TBMA, and the more content of MAA in the compolymers resulted in lower stability. Terpolymer from BOEMA, MAA and St had higher thermo-stability than those from BOEMA, MAA and isobornyl methacrylate or methyl methacrylate.

当树脂中MAA含量较低时，BOEMA与St的共聚物和BOEMA与IBOMA或MMA的共聚树脂相比，表现出更好的热稳定性，分解温度有明显差异(相差30度以上)；另外，湿度对BOEMA的聚合物的稳定性也有很大影响，湿度越高，树脂分解越快。

Green function defined inphase space differs from one in coordinate space by its struc-ture which exhibits nonlocatity in coordinates and oscillatorybehavior with respect to momenta.

在相空间中定义的Green函数不同于通常坐标空间的Green函数，在结构上显示出对坐标的高度非局域性，而对动量则显示出振荡行为。

The upper front part of a saddle;a saddlebow.

前鞍桥马鞍前面的上部分；前鞍桥