查询词典 thermal element

The Baker model and elasto-plastic finite element method are applied to investigate the thermal stress distribution in over lap zone of the single lap joint.

利用Baker模型和弹塑性有限元方法研究了胶接接头搭接区残余应力的分布。

In this paper a finite element model with the moving heat source and mesh remove technique in software package ABAQUS is used to simulate the process of percussion drilling with ultrashort laser. The temperature profile and residual stress distributions around the laser-formed hole can be calculated by a sequentially coupled thermal-stress analysis.

本文尝试以有限元素分析软体ABAQUS，利用移动热源之观念及网格移除技术来模拟超快雷射的多脉冲钻孔加工过程，以描绘出钻孔周遭的温度分布曲线，并透过顺序偶合法分析其所造成的应力场分布情形。

We have carried out the fundamental research in the following respects: Substrate stress redistribution is analyzed in vacuum evaporating deposition, A model was built to confirm that the gravitational stress formed by sustain and thermal stress induced by temperature gradient influence little to optical element figure after deposition.

首先，对真空蒸镀过程中，基底自身应力的分布状态变化进行了分析。通过建模分析表明，由装夹产生的基底自重应力和温度梯度形成的热应力对镀膜元件的面形影响很小，可忽略不计。

Homogeneously heating can be obtained by employing the steel tile s as thermal balance medium in horizontal roller track style tempering oven and the steel tile can also act as a protector of heating element.

采用钢瓦作为水平辊道式钢化炉热平衡介质，实现了均匀加热，并对加热元件有保护作用。

Analysis the reason that the asphalt concrete occurs temperature isolation in the midway of transportation by tip truck, and according to the method of finite element method take each kind of reason as thermal burden adds into the simulation model.

分析自卸车运送中沥青混合料温度离析产生的原因，并将各种原因按照有限元方法，作为热学载荷施加到仿真模型当中。

Sb doped Ti-base tin dioxide electrode with an inter-layer was prepared by electrochemical deposition and thermal oxidation. The micrograph of the electrode surface, the element composition of different layers and the structure of the electrode surface were analyzed by SEM, EDX and XRD.

采用电沉积热氧化法制备了含有中间层的Sb掺杂钛基SnO2 电催化电极(Ti/SnO2)，采用SEM、EDX以及 XRD 等检测方法对所制备电极的表面形貌、元素组成及结构进行分析，并以苯酚为目标有机物，研究所制备电极对有机污染物的电催化降解能力。

A finite element code is developed to calculate the temperature distribution of the inlet duct with the thermal barrier.

本文利用自行编写的有限元程序计算了进气道截面的温度场，并通过参数分析讨论了涂层选材及涂层结构对热防护效果的影响。

The two-dimensional transient finite element analysis and thermal responsecalculation were carried out for prestressed concrete box girder with irregular crosssection. Various boundary conditions were discussed in detail.

在有限单元分析中，首次推导出混合边界单元的计算公式，从而将第二类边界条件和第三类边界条件统一起来，以第三类边界条件的形式施加到单元边界上。

With the finite element analysis software ANSYS and limited measured temperature data, red copper and brass FSW process thermal-structural coupled analysis was done.

利用有限元分析软件ANSYS，结合几个测温点温度变化的实验数据，通过间接热力耦合分析法对紫铜板与黄铜板FSW过程进行了模拟。

Finite Element Analysis of Thermal Effect of Photovoltaic Detector Irradiated by Laser .

激光辐照光伏型光电探测器热效应的有限元分析。

Finally, according to market conditions and market products this article paper analyzes the trends in the development of camera technology, and designs a color night vision camera.

最后根据市场情况和市面上产品的情况分析了摄像机技术的发展趋势，并设计了一款彩色夜视摄像机。

Only person height weeds and the fierce looks stone idles were there.

只有半人深的荒草和龇牙咧嘴的神像。