查询词典 the maximum

The test results showed that when the cycle water flow was 65m^3/h and the oxygen flow was 1, 2,……, 10L/min, the relationship between the dissolved oxygen and oxygen flow in the water was y=0.1009χ^2+0.0594χ+5.9588 (r=0.9927). According to the mass balance principle, the maximum oxygen utilization rate of oxygen cone was calculated at 84.56%. Under the condition of the maximum oxygen utilization rate of oxygen cone, according to the rate of Nile tilapia oxygen consumption, the number of oxygen cone was projected in industrialized fish farming system. It provided the basis for oxygen supply system design in industrialized fish farming system.

结果表明，在循环水流量为65 立方公尺/h，水温24.5℃，氧气流量为0， 1， 2，……，10 L/min的条件下，溶氧与氧气流量回归方程为y=0.1009χ^2+0.059 4χ+5.958 8(r=0.9927)；根据物料平衡原理，推算出氧气锥的最大氧气利用率为84.56%；在最大氧气利用率的条件下，依照尼罗罗非鱼的耗氧率计算模式，推算出工厂化养鱼系统需配置氧气锥的台数。

When chemostats were used to study the Monod kinetic coefficients of garbage digestion under thermophilic condition, it was found that the maximum yield coefficient, the decay coefficient, the maximum specific utilization, and the half-velocity constant were 1.747 mg VSS/mg COD, 0.1191 1/d, 0.326 mg COD/mg VSS-d, and 2715 mg COD/L, respectively.

在温度因子对厨余之水解实验结果方面，热前处理温度设定为37℃、50℃及60℃达84小时后，发现以60℃处理之水解率(18.1%)及油脂去除率(37.7%)最高；将上述经37℃、50℃及60℃处理84小时之厨余，以气泡式呼吸仪实验探讨生物分解性之结果亦显示，以60℃处理时经过约300小时后TCOD去除率79.2%最高。

Analyzing the calculating process of belt conveyor with high angle theoretically, starting from its theoretic calculate the cross sectional area of materials and peripheral force, shaft power of drum, power of motor, using point by point method to get the resultant strain of every drum and torsion of driving drum, calculating the maximum strain and the maximum reverse stopping torque, to give the support on theory for using belt conveyor with super-long distance, high angle under the coal mine.

本文针对长运距、大倾角、高强度带式输送机设计过程中存在的问题，从四个方面对大倾角带式输送机进行分析研究：从理论上解析大倾角带式输送机的计算过程，从大倾角带式输送机的理论入手，详细计算物料的横截面面积、圆周力、滚筒轴功率和电机功率，利用逐点计算法计算各个滚筒的合张力以及传动滚筒的扭距，计算出胶带的最大张力和最大逆止力矩，给长运距、大倾角皮带机在煤矿井下的使用给予理论上的支持。

The read-write function and the data collection of the electronic label can read and write, collect data at the 125KHZ and 13.56MHZ in wireless condition. The maximum distance for reading and writing is 1.5m , and the maximum simultaneous reading is 50pcs papers. One pc paper is read in 0.1second, and an output of 12V/ 1A switch coulometry controls other devises.

本项目研制的电子标签读写和数据采集设备具有对 125KHZ 、 13 。56MHZ 的电子标签在无线状态下进行读写和数据采集，最大读写距离可达 1.5m ，最多可同时读取 50 张，单张读取时间 0.1 秒，可输出 12V/1A 开关电量，控制其它设备。

The analysis shows that, the maximum stress change appears in the heat affected zone of the flange's center and it has main influence on surface crack of flange plate and the maximum stress is less than the allowable stress 235 MPa of the material, which is in the reliable range.

分析结果表明，最大的应力变化出现在法兰盖板中心的热影响区，对盖板表面裂纹有主要的影响，最大应力小于材料的许用应力235 MPa。

The analysis shows that, blade vibration and torsional deformation is the mainly manifestations of the cutting mechanism head body ,the maximum deformation of the helical blade is 18.01mm, the maximum stress value in the welding of corner ,connection of end disk and helical blade is the weak link, helical blade is the main component, which effects the dynamic characteristics of cutting mechanism head body.

所得结论对于改进螺旋钻采煤机截割机构头体的设计、提高其动态性能和使用寿命具有一定的指导意义和参考价值。2、文章中部分措词需要修改，摘要翻译中文化，论文整体格式需要修改。3、数值模拟的约束条件有待商榷，对于结果应该对比实际试验和有关材料特性表，更有说服力。

This analytical approach shows that, as increasing the wear flat of indenter, the maximum indentation force needed to develop critical plastic zone increases and its corresponding critical penetration depth also increases slightly, Note that the effect of wear flat will affect rock fracture behavior. In addition, regarding the simulation of the effect of doubled-indenters, result shows that two adjacent indenters may interact each other as reaching the transient/critical relative space between indenters of 2~3. It dicpicts that a proper spacing arrangement between indenters may enhance a efficient mechanical cutting due to the less required maximum indentation force and energy dissipation.

由数值模拟之结果得知，当楔尖磨耗增加时，岩材产生脆性破坏之初裂贯切力随之增加，而其对应之临界贯入深度则亦微幅增加，故磨耗效应确会干扰岩材脆性破坏机制之形成；而由双刀效应之模拟，可知两贯切刀楔互制影响之破坏裂缝生、衍行为，当双刀相对刀距为时，岩材之破坏特徵有明显变化，即定义此为临界相对刀距，并探讨其产生脆性破坏所需初裂贯切力之变动范围及应力重叠区，由此得知适当之刀距安排将有助於减少能量之耗损。

The law was alike between initial stage and the peak of growth, but the rates reaching maximum of negative and positive were in the different soil depths , and the inflexions of increment anti decrement by degrees were also different. The soil water content in terminal stage increased positively, and in surface reached the maximum, but decreased with the depths, except a little increment in the depth of 460~600cm.

年生长季内，不同生长时期，土壤含水量变化的速度不同，生长初期和生长旺季的规律相似，但速度出现负的最大和正的最大所在的土层深度不同，速度递增和递减所在的土层深度也不同，生长末期速度均为正值，表层最大，随土层深度的加深，速度递减，但到460~600 cm处速度略有增加。

Using high frequency induction brazing and TiZrNiCu filler metal, the shear strengths of the joints were low. The maximum shear strengh was only 102.1MPa, which was lower than the maximum strength of vacuum brazing. The reasons may be that excessive intermetallics, holes and oxidation existed in the joint. So TiZrNiCu filler metal isn't fit for non-vacuum brazing.The stress variation, stress distribution and crack-sensitive regions during the cooling process of brazing have been studied by Marc non-linear software.

采用气体保护高频感应加热、TiZrNiCu钎料钎焊时，接头的强度普遍偏低，最高的剪切强度只有102.1MPa，远远低于辐射加热真空钎焊的强度，其原因是接头中局部生成了过量的金属间化合物，且产生氧化，接头中含有较多的气孔等影响了接头强度，因此可以认为TiZrNiCu钎料不适合在非真空条件下的钎焊。

The results showed that the stearates can accelerate the development of PTG material. The addition of NiSt2 greatly increased the maximum density and the sensitivity together with a slight fog increase. However the addition of BaSt2 and CaSt2 did not make such great increase in the maximum density and the sensitivity, together with a slight fog decrease.

结果表明，MSt2的加入可促进PTG材料的显影，其中加入硬脂酸镍(NiSt2)后在灰雾增加不大的情况下，最大密度和感光度大幅度提高，而加入硬脂酸钡(BaSt2)和硬脂酸钙(CaSt2)后在抑制灰雾的同时，最大密度和感光度也有一定程度的增加。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐