查询词典 the force of inertia

The inertia force and coriolis force are calculated to draw deviation for opposite balance, fall and plane motions close to the earth, based on the particle motion differential equation to no-inertial frame of reference.

在质点对非惯性参考系的运动微分方程的基础上，计算惯性离心力和科里奥利力对地球表面附近物体的相对平衡，落体运动和平面运动引起的偏差。

Base on the lumped parameter model of the torsional vibration system of crankshafts with variable inertia and considering the nonlinear elasticity force and nonlinear dissipative force, a six-degree-of-freedom nonlinear dynamical equations with parametric excitation and compulsive force are deduced.

从旋转惯量变化的曲轴扭振系统的集总参数模型出发，同时考虑了系统的非线性弹性力和非线性耗散力，导出了参强联合作用下的六自由度非线性扭转振动微分方程。

Based on the time history analysis performed on three kinds of high-rise block masonry structures (10-story, 15-story, 18-story structures respectively) and the study on the inertia force distribution of the structures, a new pattern of lateral force distribution, namely parabolic distribution pattern, is presented here.

对3种不同中高层砌块砌体结构(分别为10层、15层和18层砌块砌体结构)进行大量时程分析，对结构的惯性力分布进行研究，提出一种新的适用于中高层砌块砌体结构Pushover分析的侧向力分布模式-抛物线型分布模式，并用该模式分别对3种砌块砌体结构进行Pushover分析。

This thesis DESign steel wire tension control system of Steel Billet Grinding Machine, and establish mathematical model of every component in electro-hydraulic proportional valve control dissymmetry hydraulic cylinder servosystem and the load with large inertia and flexibility system of Grinding Machine. Through the medium of matlab/simulink simulation, this thesis mostly analyses Pre-load impact of steel wire stress. Compare with the emulation result of non-feedback, force feedback, displacement feedback, thereby educe reliable conclusion.

本文设计了钢坯修磨机钢丝绳张力控制系统，并且对电液比例阀控非对称液压缸伺服系统的所有液压元件和修磨机柔性负载系统进行了建模，通过MATLAB／SIMULINK仿真，主要分析了预紧力对钢丝绳受力的影响，而且对开环无反馈、力环反馈、位移反馈的仿真结果进行了比较、得出了可靠的结论。

And the grasp features of the combined numerical cyclist dummy's hand is determined by simulation experiments, highlighting the interaction force between the cyclist and the two-wheeler, the driving inertia of the two-wheeler, the coupling force between the tyre and the ground, and thus set up the human-vehicle-road coupling system simulation model.

通过仿真试验确定组合式骑车人数值仿真假人的手部抓握特性，突出骑车人与两轮车之间的相互作用力，两轮车的行驶惯性和其轮胎与地面之间的耦合力，从而建立了骑车人-两轮车-路面耦合系统仿真模型。

Analyzed the stress distribution under the common act of the environment temperature, inertia force and shrink fit when the rotor was working.

转子工作时，在环境温度、惯性力及过盈配合等多种因素的共同作用下，分析了转子的应力分布。

When the lock ring simultaneously with the question cone gear engagement ring gear, cone after contact friction moment in the role of the rapid speed of gear to reduce to synchronize with the speed equivalent to lock ring, the two synchronous rotation, relative to gear Central lock synchronization speed is zero, thus inertia torque also disappeared, then in force under the impetus of engagement sets unhindered and synchronization lock Gear engagement ring, and further engagement with the question of gear engagement ring gear and completed Shift process The topics mainly through the Pro / E synchronization software for the car to three-dimensional modeling structural design, and through the parameters of the design process to achieve its structure, and on this basis, the use of ANSYS FEM software structure of the typical synchronization And a finite element analysis, through structural analysis of its structural design is reasonable to assess and make recommendations to improve the design

当同步锁环内锥面与待接合齿轮齿圈外锥面接触后，在摩擦力矩的作用下齿轮转速迅速降低到与同步锁环转速相等，两者同步旋转，齿轮相对于同步锁环的转速为零，因而惯性力矩也同时消失，这时在作用力的推动下，接合套不受阻碍地与同步锁环齿圈接合，并进一步与待接合齿轮的齿圈接合而完成换档过程本课题主要是通过Pro/E软件对汽车同步器进行三维造型结构设计，并通过参数化实现其结构设计程序化，在此基础上，利用ANSYS有限元软件对典型同步器结构进行有限元计算与分析，通过结构分析对其结构设计的合理性作出评价并提出改进设计建议

The excitation sources of vibration in a in-line 4-cylinder engine include second-order inertia force induced by piston reciprocating movement and rolling moment caused by the side force exerted on cylinder.

四缸发动机的主要激振源为活塞往复运动产生的往复惯性力和气缸承受的侧压力产生的倾覆力矩。

The inertia, however, keeps the air moving over the wing from 'pushing' against the top of the wing with as much force as it would if the wing wasn't moving.

惯性，但是，保持空气移动超过机翼从'推'对上方的机翼与多力量，因为它将如果机翼不动。

First, natural frequency of Euler-Bernoulli beam with elastic bearing and without the axial force is put forward. And numerical method is used to solve the equation by a program designed by the author, and the influences of shearing deformation and rotatory inertia on frequency are analyzed.

首先对不考虑轴力影响的弹性支座Euler-Bernoulli梁的固有频率进行了推导，并用自编程序进行了数值法求解，同时分析了剪切变形和转动惯量(Timoshenko梁)对频率的影响。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。