查询词典 the bulk of

The granularity and broken cellular wall of ultra-fine powder were studied by JL9200 laser analytical instrument of granularity and scanning electron microscopy, as well as the bulk density and liquidity of "Cumiansan" ultra-fine powder were measured, and compared to the commonly cribble.

应用激光粒度仪和扫描电镜对微粉的粒度和破壁情况进行了观测，测定了&促免散&微粉的堆密度及流动性，并与普通粗粉进行了比较。

The results showed that the D50 of Astragalus membranaceus and Epimedium brevicornum ultra-fine powder were 6.82μm and 8.40μm separately. The broken cellular walls of two ultra-fine herbal powder were bigger than those of the commonly cribble, and intact cells were not visible under SEM, and it improved the mixed uniformity. On the contrary, organization blocks of the commonly cribble were clearly discernible, also the shape and granularity were irregular, and the organization cells were still complete. The bulk density and liquidity of Astragalus membranaceus and Epimedium brevicornum increased significantly after ultra-fine Smashing. The component icariin extraction content of the ultra-fine powder was enhanced by 18.31% compared with the cribble by the chromatograph analysis of icariin. At the same time, Astragalus membranaceus polysaccharide and Epimedium brevicornum polysaccharide content of the ultra-fine powder were enhanced by 117.13% and 315.15% compared with the cribble.

结果发现黄芪和淫羊藿经超微粉碎后，粉体的粒度分布中心D_(50)分别为6.82μm和8.40μm，经电镜观察均难以看到完整的细胞形态，只能看到细胞碎片，破壁率远远大于普通粗粉，其混合的均匀度显著提高，而普通粗粉在显微镜下，组织块清晰可见，且形状不规则，粒径分布不均匀，组织细胞仍然完整；超微粉碎后，黄芪和淫羊藿的堆密度和流动性显著增强；通过对淫羊藿有效成分淫羊藿苷的色谱分析，其中淫羊藿超微粉的淫羊藿苷体外溶出量较淫羊藿粗粉中提高了18.31%；同时黄芪、淫羊藿超微粉多糖的提取率分别较黄芪、淫羊藿粗粉提高了117.13%，315.15%。

As finished restructure power unit , would not change bulk and build technique, so framework and bracket of power unit not need restructure, at on time it not change intricate rigid connect frame of main loop in power unit , only change crustaceous configuration have already preconcerted objective.

功率单元结构更改后，其大小和安装方式未变，所以变频器的功率柜内的结构体与功率单元托架无需改变，同时功率单元内部的主回路的复杂刚性电气连接件均未改变，只是对外壳结构体进行改动就完成了预定的目标。

The carbon foam were prepared by self-bubbling at high pressure from AR pitch added sodium dodecyl benzene sulfonate and Span-40, respectively. The bulk density, pore rate, compressive strength, thermal conductivity at room temperature and crystallitic parameters of carbon foam were measured. The rheological properties of AR pitch and pore structure of carbon foam were investigated.

以十二烷基苯磺酸钠和Span-40表面活性剂为添加剂，AR沥青为原料，制备炭素泡沫材料，测定了材料的体积密度、显气孔率、压缩强度、常温热导率以及微晶结构参数，研究了添加表面活性剂后AR沥青的流变性能和炭素泡沫材料孔胞结构的变化。

The FDA said the bulk of tests in 87 formula samples came back negative for both melamine and cyanuric acid.

FDA表示，对87份配方奶粉样品的检测，大部分回报三聚氰胺和三聚氰酸均为阴性。

Dabba buys phone minutes in bulk and sells them in the form of pay-as-you-go cards.

Dabba批量买进电话时段并以电话卡的形式将其卖出。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area;2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support;3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier;4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling;5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene PolymerizationIn this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that:1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS;2.co-mlling time had no obvious effect on the texture of support after 12 hours;3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现；3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布；4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒；5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明：1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致；2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响；3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area; 2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support; 3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier; 4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling; 5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene Polymerization In this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that: 1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS; 2.co-mlling time had no obvious effect on the texture of support after 12 hours; 3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现； 3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布； 4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒； 5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明： 1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致； 2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响； 3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

The results of clarification experiments show: the mixed juice was treated by microbial flocculants MF-C; it could effectively improve the settlement speed, reduce the bulk of mud, decolorize and reduce turbidity of the juice. The AP of juice that was treated by microbial flocculants is higher than that of PAM.

澄清实验结果表明：用MF-C絮凝剂处理混合汁可有效提高混合汁的沉降速度，压缩泥汁体积并有较好脱色除浊效果，同时清汁纯度较用PAM处理的还略有提高。

Biomass in the rain forest was far more than that in the plantation of 12 years,especially for the shrub layer.But the biomass of litterfall collected in the plantation was greater than that of the rain forest for the reason that Betula alnoidis defoliated in dry seasons.9 Four years observation found that soil bulk density tended to increase first, then decrease after planting trees;total soil porosity and non-capillary porosity tended to decrease and after few years they recovered to different degrees;the soil cation exchange capacity for all forest types increased;in the soil of 0-30cm depth,soil salt saturation tended to decrease;nutrient content in the soil of 0-60cm depth in the young stand tended to decline;soil effective P,effective K and N contents all tended to decrease.

山地雨林的总生物量远远大于10年生的西南桦人工林，其中灌木层的相对差别尤其巨大。94次的观测发现，人工林栽植后，土壤容重一般呈现一个先上升后下降的特点；而土壤非毛管孔隙度、土壤总孔隙度大多呈下降趋势，几年后有不同程度的恢复。

As of Tuesday, Google's results were still censored in China.

截至周二，谷歌的搜索结果仍受中国审查。

In order to make the positive action increase and negative one decrease, the sub-forces of the social factors must be adjusted to form a centripetal force.

在这一过程中，人的主体性发挥是社会有机体健康发展的灵魂。