查询词典 tensile

Reasonable baseline is one of the key matter in the straightness measurement. Two schemes of the measuring basis are advanced in the paper--tensile spring and laser beam, based on the request and character of guide-ways straightness measurement. In early study, we come to the conclusion by theoretical analysis and experiment that the laser beam basis has more advantage in development and accuracy.

合理的直线基准是实现直线度测量的一项关键内容，本文首先针对导轨直线度的测量要求与特点，提出了张丝与准直激光束两个测量基准方案，并在前期研究中通过理论分析与大量的实验对比得出结论：激光束在系统实现及测量精度等方面均具有更高的优越性。

It is important to use 7% stearic acid in order to make inorganic ions dispersing in HDPE and to improve the tensile properties of composite plastic.

结果表明：用质量分数为7%硬脂酸改性的纳米CaCO3，能较好地促使无机粒子的分散和与HDPE的结合，提高复合塑料的拉伸性能。

Different surface modifiers (benzoate, stearine acid and organosilane) were used to treat plant cellulose/polypropylene composite systems. Effects of surface treatment agents on mechanical properties ( tensile strength and impact strength) were studied.

采用不同的表面改性剂(苯甲酸、硬脂酸、有机硅烷)对植物纤维/聚丙烯复合体系进行了处理，研究了表面改性剂对体系力学性能的影响规律，探讨了复合材料界面粘接机理，分析了力学性能的变化规律。

The results show that Bi and Sb are mainly distributed on grains and grainboundaries, and Bi on grainboundaries there are mainly simple substance Bi particles, Sb in grains are intermetallics containing stibium. The tensile strength, yield strength, elongation and variation of area of halfhard brass containing bismuth and stibium are 478.9 MPa, 295 MPa, 15.1% and 29.3% respectively. Corresponding to HPb59-1, the cutting property of brass containing bismuth and stibium is excellent. The brass containing bismuth and stibium shows excellent dezincification corrosion resistance, and the depth is 323 μm.

结果表明：添加的Bi和Sb主要以单质或化合物方式存在于无铅黄铜的相内和相界处，Bi以单质颗粒存在于相界处，Sb以化合物形式存在于相内，这对提高合金切削性能有利；添加Bi和Sb黄铜的抗拉强度为478.9 MPa，伸长率为15.1%，断面收缩率为29.3%，屈服强度大约为295 MPa；添加Bi和Sb黄铜的切削性能比HPb59-1铅黄铜的优，合金的脱锌腐蚀性能良好，脱锌层厚度约为323 μm。

The tensile intensity and stiffness were measured after 45, 90 and 180 days separately after operation.

术后45、90 及180 d 测量移植物的刚度和最大抗拉强度的变化。

Based on the matrix strength stochastic distribution theory and the fiber failure stochastic distribution theory, the stress-strain behavior and the tangent tensile modulus are obtained for unidirectional composite (0$^\circ$ ply).

基于基体随机开裂、纤维随机断裂分布理论，得到正交铺层结构的应力-应变关系；基于体积平均方法，将纤维束波动部分进行分割，引入强度分析模型，得到纤维束波动部分的应力-应变关系。

The existing problems of tensile control system of tubular strander and locking device of frame of spool are pointed out.

指出管式捻股机张力控制系统和工字轮框架锁紧装置存在的问题。

To analyze effect of tensile value and uniformity of wire and strand on quality of wire rope during stranding wire rope.

在捻股和捻绳时，钢丝或股的张力大小及均匀性对钢丝绳的质量有很大的影响。

The strawboard bonded with NaOH modified SPI adhesive showed the best properties with the temperature of 140℃, pressure of 8MPa, time of 10 min, and initial moisture content of 30%. The properties are as the following: tensile strength 2.70MPa, modulus of rupture 8.42MPa, modulus of elasticity 456.33MPa, and with the water absorption of 102.34%.

试验结果表明，NaOH改性大豆分离蛋白胶粘剂条件下，当模压温度为140℃，压力为8MPa，成型时间为10min和稻秸初始含水率为30％时，稻秸板的抗拉强度为2.70 MPa，静曲强度为8.42 MPa，弹性模量为456.33 MPa，阻水性为102.34％。

The strawboard bonded with urea modified SPI adhesive showed the best properties with the temperature of 150℃, pressure of 8MPa, time of 20 min, and initial moisture content of 30%. The properties are as the following: tensile strength 1.92MPa, modulus of rupture 12.9MPa, modulus of elasticity 581.16MPa, and with the water absorption of 112.09%.

试验结果表明，脲素改性大豆分离蛋白胶粘剂条件下，当模压温度为150℃，压力为8MPa，成型时间为20min和稻秸初始含水率为30％时，稻秸板的抗拉强度为1.92 MPa，静曲强度为12.9 MPa，弹性模量为581.16 MPa，阻水性为112.09％。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。