查询词典 tensile strength

It was found that the puncture strength, tensile strength and modulus as well as the inverse of relaxation coefficient of starch/dHG films pronouncedly increased with increasing dHG, accompanied with a decreasing tendency in puncture deformation, extensional creep compliance, retardation time and tensile strain at break.

淀粉/dHG可食膜的穿刺强度、抗张强度、抗张模量及应力松弛系数的倒数，随脱色仙草叶胶浓度增加而增加，而穿刺变形量、依顺值、及抗张变形量则减少。

The results showed that the tensile strength and elongation at break of the objective silicone rubber increased with the increase of vinyl content in PDM-MVS. The tensile strength was 3.9 MPa and elongation at break was 416%, and the reinforcement effect of PS on silicone rubber was significant when the mass fraction of vinyl was 1.50%. The objective silicone rubber had microphase-separated structure consisting of PS domains uniformly dispersed within a continuous PDM-MVS matrix. The compatibility between the two phases increased with the increase of vinyl content in PDM-MVS.

结果表明，目标硅橡胶的拉伸强度和扯断伸长率均随PDM-MVS中乙烯基质量分数的增加而增大，当乙烯基质量分数为1.50%时，其拉伸强度达3.9 MPa，扯断伸长率达416%，PS的增强效果明显；目标硅橡胶具有微相分离结构，PS作为分散相均匀分布于PDM-MVS连续相中，两相的相容性随着PDM-MVS中乙烯基质量分数的增加而增强。

The break elongation of vulcanizate was increasing with chlorine content. When the chlorine content was higher than 16%, the tensile strength was gradually decreased with the chlorine content. The break elongation was increasing with the content of chlorinated EHL, while the tensile strength was decreased.

硫化胶的扯断伸长率随着氯含量的增大而增大，当氯含量大于16%时，拉伸强度随着氯含量的逐渐增大而降低，并且扯断伸长率随着添加量的增加不断增加，而拉伸强度有所降低。

The results indicated that, the stress-strain curve of bottom stems obeyed Hooke's law; the tensile strength of Bromus inermis was higher than Coronilla varia, but the elastic was smaller; the tensile strength and cellulose contents of Coronilla varia were smallest (13.87%) in the four species.

研究结果表明：4种牧草收割期底部茎秆应力σ与应变ε曲线服从虎克定律，禾本科扁穗冰草茎秆抗拉强度高而弹性小；豆科小冠花茎秆抗拉强度最低，柔韧性强，纤维素质量分数也最低（13.87%）。

Totally 60 semi-circular bending specimens cored from superpave gyratory compactor with three groups of notch depths are tested at the temperature of-10 and 20℃ The experimental results reveal good repeatability in EAM characterization. The tensile strength ratio of SCB to the indirect tensile test is at a range of 1.4 to 1.7, and the ultimate strength of EAM is exponentially dependent on the notch depths. At the test temperatures, the critical J-integral value of EAM is much higher than that of hot mix asphalt with thermoplastic asphalt binder. The response mode of EAM changes from ductile mode to brittle mode and the fracture energy increases 30% when temperature decreases from 20 to-10℃, while its critical J-integral value decreases only 15%.

结果表明，环氧沥青混合料的半圆弯曲试验结果复现性好；由非切口试件的半圆弯曲试验与标准间接拉伸试验所测得的环氧沥青混合料的抗拉强度，其比值在1.4~1.7之间，且SCB抗拉强度与切缝深度指数相关；在20℃与－10℃试验条件下，环氧沥青混合料具有比热塑性HMA高得多的临界J-积只分值；当温度由20℃降至－10℃时，环氧沥青混合料的响应模式由延性变为脆性，断裂能增加30%，而临界J-积分值下降15%。

To guarantee high quality,BRIGHTWAY has brought in a large batch of the latest advanced equipment from around the world such as omnipotent material tester,M/I index tester,heat deflection temperature tester,RoHS test equipment,aging property tester etc.All of the production processes are under strict control and supervision ofour experienced enginners. Density,flow index,hardness,tensile-strength,tensile stetch, bending strength, flexural modulus,impact strenght, mould shrinkage factor, heat deflection temperature, fibre glass contents, water absorption, combustibility will be tested strictly by the professional engineers.

为了确保产品的高品质，百莱威引进了大量国际新一代的先进设备，如万能材料试验机、M/I指数测定仪、热变形温度测定仪、RoHs检测设备、耐老化试验设备等等，并且所有的生产过程都受到了严格的质量控制，由经验丰富的专业工程师进行了密度、流动指数、硬度、拉伸强度、伸长率、弯曲强度、冲击强度、模收缩率、热变形温度、玻纤含量、吸水率、燃烧性能等十多项苛刻的评审和检测。

Application experiment shows that the tensile strength of the modified nano-silica-filled vulcanizes is 8.22MPa when the content is 1.0%, elongations of vulcanizes is 823.15%. When the content is higher than 3.5%, the tensile strength increases and reaches 9.28 MPa, elongations of vulcanizes decrease to 746.56%.

应用实验表明，硫化胶中填充1.0%的改性纳米二氧化硅，硫化胶的拉伸强度为8.22MPa，拉断伸长率提高到823.15%；纳米二氧化硅填充量增加至3.5%，拉伸强度增至9.28MPa，拉断伸长率下降到746.56%。

The results demonstrate that welds with good appearances could be obtained when welding with the appropriate processing parameters. The as-welded joint tensile strength without filler wire is 180.7 MPa, while the tensile strength is 190 MPa when welding by one side with the filler wire of AlSi12 or AlMg4.5MnZr.

研究结果表明，在合适的工艺参数下，可以获得表面光洁、正反面焊缝成型良好的对接接头；焊态下，单面焊接不填充焊丝的接头强度为180.7 MPa；单面焊接填充AlSi12，AlMg4.5MnZr焊丝的接头强度最低为190 MPa，且两种填充焊丝接头的拉伸强度无明显差异；双面焊接填充AlMg4.5MnZr焊丝的接头强度达到200.7 MPa，约为母材的90%。

Based on the trial of two different heat treatment processes for TP321 tube blank ,this paper revealed influence of solution treatment and solution treatment plus stabilization treatment on room temperature tensile strength,elevated temperature tensile strength,microstructure and grain size of TP321 tube blank .

通过对 TP321管坯材料的热处理工艺试验，阐述了材料经固溶处理和固溶处理+稳定化处理这二组热处理工艺后对材料室温和高温拉伸性能、组织和晶粒度的影响。

As for the factitiously specified allowable values,such as allowable deflection,allowable amount of wear,and so on,their magnitudes,which are confirmed on the basis of empirical formula,often have an interval value or a limit value,therefore they can be described suitably by minor type membership function, As for various strength values of parts,such as tensile strength,compression strength,contact strength and so on,their magnitudes,which are often confirmed only by approximate mean,can be described suitably with middle type membership function.

对于人为规定的各种许用值，如许用挠度值、许用磨损量等，根据经验公式确定它们的大小时往往有一个区间或一个极限值，宜用偏小型隶属函数描述，对于零件的各种强度值，如抗拉强度、抗压强度、接触强度等，实际中往往只能确定其近似的均值，宜用中间型隶属函数描述。

"Yes, now you can give yourself airs," she said, you have got what you wanted.

"对了，您现在高兴了，"她说道，这是您所期待的。

Then the LORD said to me: Rebel Israel is inwardly more just than traitorous Judah.

上主于是对我说：＂失节的以色列比失信的犹大，更显得正义。