查询词典 tensile strain

As the caprylic aldehyde content increased,strain at break and tensile strength were decreased.

拉伸强度和断裂伸长率均随辛醛含量的增加而降低。

The cruciform biaxial tensile test is an effective and practical method to realize the process of complex strain paths.

通常由标准实验确定的FLD都是由线性或近似线性的应变路径得到的。

Moreover, it is found that analysis on bond length, torsion angle and strain energy can help to study the localization and the size of a knot in the tensile process.

键长、键角、两面角和能量的分布及其在拉伸过程中的变化能够帮助确定结在链中的定位，分析结的尺寸。

Tensile strength,coercive force and residual magnetization of the wire are increased with increasing drawing strain.

由于变形应变量的增大，微缺陷密度升高，钢丝矫顽力Hc和剩余磁化强度Mr都随之变大。

It is shown that the mechanical properties including Young's modulus, tensile strength, critical strain and stress under buckling can be enhanced with the decreasing of intershell spacing. The shear strength can be enhanced by 2-3 orders of magnitude when the intershell spacing is reduced to 20%, which is also dependent on commensuration. Zigzag-type carbon nanotubes have higher shear strength. The axial stress in tubes when the load transferring from outmost tube to inner tube is observed as well.

研究了单壁纳米管束横截面的六方化失稳现象，给出各种管径的面内压力－应变关系曲线；每条曲线都给出一个明显的拐点而且有很强的非线性；线弹性模量与参考构形有关，也受管直径的影响；分析了管束横截面的晶格不稳定性特征，表明晶格的缺陷能够明显的减小临界值；模拟了在不同应变下纳米管束对静水压的反应，发现不同压力下的截面形态不同，在很高压力下相邻管之间会形成化学键。

The stress-strain curves of Cu-Zn-Al alloys at different temperatures have been plotted on the tensile machine with the aid of electrometry. The main results were as follows: 1. When specimens were deformed within the range of M_s and M_d, the critical stress for inducing martensitic transformation increased with the temperature, and there existed a linear relationship between them. 2. When specimens were deformed above Af, complete pseudoelasticity might be obtained theoretically, which might be damaged, h...

在拉力试验机上用电测法测绘了Cu-Zn-Al合金在马氏体相变点上下各温度的σ-ε曲线，所得主要结果如下：(1)试样在M_s与M_d之间加载，随着温度升高，诱发马氏体相变所需临界应力增大，且加载温度与临界应力之间存在着线性关系；(2)在A_f点以上加载，理论上可获得完全的伪弹性，但加载温度过高或应变量过大，均会损害伪弹性；(3)试样在M_s点上下温度区域变形，得到的伪弹性回复和形状记忆回复之和在80%以上，但在M_s点附近总回复量出现一极小值，且伪弹性回复在M_f点以下又有所回升。

The effects of strain rate and temperature on the tensile yield strength and elongation of titanium aluminides are studied.

摘 要 研究了应变速率和温度对Ti45Al10Nb合金的屈服强度和延伸率的影响。

Based on the stress-strain relationship, tests, no tensile stress of masonry and assuming resistance submit gauss distribution, the resistance equations and its statistic parameters are obtained.

从圬工材料的应力—应变关系曲线出发，并假设圬工材料不抵抗拉应力，推导出了截面抗力的表达式并根据现有的试验资料统计，假设抗力服从正态分布，统计出分布参数。

The tensile stress-strain curves of the multi-layer composite were predicted by correcting Lee's equation, and these predictions showed good agreement with the experimental data when form harden was taken into account.

此外本文还在前人的研究基础上，经过分析与修正，提出了一种能比较准确地预测不锈钢／铝／不锈钢多层复合板的真应力—真应变曲线的方法。

The deformation mechanism is mainly the single-slip and cross-ship, the fracture mechanism is mainly the congregation of transgranular micro-hole, and large uniform deformation occurred before tough fracture, and therefore, the ability of plastic deformation and the mechanical properties of the material were remarkably improved. These fully indicate that the new melt-treatment developed in this work is an effective and advanced technique, and further testify that the improvement of metallurgical quality of the material is the key to enhance its mechanical properties, especially its plastic deformation performance. The results of tensile and compression tests at elevated temperature also indicate that the suitable hot-working temperature range is 400～450℃. 4. A steady-state plastic flow exists during the plastic deformation of the aluminum sheet used for pressure can at elevated temperature. A hyperbolic sine relationship can be satisfied between the steady-state flow stress and strain rate by introducing an Arrhenius term which involves some thermal activation parameters, i.

压力罐用铝材中的主要冶金缺陷为Al〓O〓夹杂物、气孔及富Fe杂质相；高效熔体处理显著改善了材料的冶金缺陷的存在形态，使含杂量明显减少、夹杂物尺寸变细小且分布均匀，富Fe杂质相变为细小、分布均匀的团球状或短棒状的复杂化合物，同时也明显细化了结晶组织；此外，由于高效熔体处理有效地减少了材料中裂纹萌生源数量，因而改变了材料的塑性变形微观过程及断裂方式，主要以单滑移和交滑移进行塑性变形，断裂方式为穿晶微孔聚集型，韧性断裂前产生了大量的均匀变形，不易出现变形失稳，从而显著提高了罐用铝材的塑变能力和力学性能。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。