查询词典 temperature

A mathematic model,which deals with the relationship between maximum temperature of thick plate butt multipass welding and weld heat input,interpass temperature,ambient temperature and the distance of measuring points to heat source center,was founded using multivariant nonlinear regression analysis.

采用多元非线性回归的方法，建立了厚板对接多道焊的最高温度与焊接线能量、层间温度、环境温度以及测点到热源中心的距离之间的数学模型。通过相关性检验、线性回归的显著性检验以及回归系数的显著性检验，证明了模型可行；同时分析了回归系数与测点到焊缝中心距离之间的关系。结果表明，它们之间的关系是一种非线性关系，而且呈现出了一定的变化趋势

This paper using the FEM software Marc, for the 50 and 60 degree V groove of flat plate butt joint simulate the one-layer and three layers welding, finish each welding and cooling it down to room-temperature then start the next welding true represent process and get the temperature field, residual deformation and welding residual stress, according to the theory analysis and empirical equation verified the temperature field and residual deformation all correct, comparison with experiment verified the welding residual stress regularity and correctly.

本文利用有限元软件Marc，对开60°和50°V型坡口的平板对接接头，动态的模拟了单层单道打底焊，焊完一道后让试件冷却到室温以及单层单道满焊，每焊完一道后让试件冷却，然后再焊下一焊道，道间温度≤200℃，在以此为初始边界条件下开始下一道的焊接，真实的再现了焊接过程，得出了温度场，残余变形和残余应力场的分布规律，根据理论分析及经验公式验证了温度场以及残余变形的正确性，角变形的大小，这些结果与数值计算相吻合。通过与实验测得的残余应力进行比较，验证了焊接残余应力的分布规律及模拟的正确性。

Machinery and Equipment: baked me, the tunnel furnace, heat shrinkable packaging machines, automatic sealing machine, high temperature resistance furnace, tin melting furnace, water POON counter, lines, car, cart, UV; electrothermal Equipment: stainless steel heating pipe, titanium tube, quartz tube, Teflon tubes, electric lap, UV lamp, silicon carbon rods, cast aluminum heater, high temperature of the radiation, the first single, high-temperature lines; plating products : PVC plated shafts, titanium basket, linked to a titanium, titanium steam pipe, the anode, filters and other machinery at a value of whole plant equipment to undertake the planning, design, production, installation, commissioning and maintenance operations, welcomed the overwhelming majority of customers来人calls Advisory negotiate!

机械设备：烘箱、隧道炉、热收缩包装机、自动封箱机、高温电阻炉、熔锡炉、水濂柜、流水线、台车、推车、UV等；电热器材：不锈钢加热管、钛管、石英管、铁氟龙管、电热圈、UV灯管、硅碳棒、铸铝加热器、高温辐射管、单头管、高温线等；创值机械同时承接整厂设备规划、设计、生产、安装、调试、维护业务，欢迎广大客户来人来电咨询洽谈！

The Company through many years of efforts, Japan,"Fuji" Motor Corporation temperature control, Japan,"Rhine" card-counting series of products, Japan,"Sanken" company converter, Japan, East licensing high-temperature electronic tape, South Korea's LG automation products, Japan's high-temperature wire agents, KSS wiring system, Germany Shi Ke SICK, South Korea Autonics AUTONICS, Japan, as God SUNX, Mitsubishi Electric and Japan's "Omron" the world Brand-name-controlled equipment for our distributors.

本公司通过多年的努力，成为日本&富士&电机公司温控表、日本&莱茵&牌计长计数系列产品，日本&三垦&公司变频器、日本日东牌高温电子胶布、韩国LG自动化产品、日本高温导线的代理商，KSS 配线系统、德国施克SICK、韩国奥托尼克斯AUTONICS、日本神视SUNX、三菱电机以及日本&欧姆龙&等世界名牌自控器材的特约经销商。

It is pointed out that due to the difference of the temperature expand coefficient of aluminum alloy gear case and steel bolt, when the temperature of the gear case increased,additional temperature-difference load is generated,which is the ultimate reason of the bolt failure.

指出由于铝合金齿轮箱和钢制螺栓的热膨胀系数不同，在齿轮箱温度升高后产生附加的温差载荷，此温差载荷是螺栓失效的根本原因，由此依据相关公式提出了改进措施。

According to heat load source of die cavity, temperature distribution gradient equations and heat flux equations and the peak value equations of temperature load at die cavity surface have been obtained with research of temperature distribution and transfer laws of die surface by unsteady heat transfer theory.

摘要根据锻模型腔热负荷来源，通过非稳态传热理论，分析研究了模具工作表面层的温度分布与传递规律，给出了型腔表面温度分布梯度和热流密度公式，并给出了锻模型腔表面的温度负荷峰值的计算公式。

According to heat load source of die cavity, temperature distribution gradient equations and heat flux equations and the peak value equations of temperature load at die cavity surface have been obtained with research of temperature distribution and transf

摘要根据锻模型腔热负荷来源，通过非稳态传热理论，分析研究了模具工作表面层的温度分布与传递规律，给出了型腔表面温度分布梯度和热流密度公式，并给出了锻模型腔表面的温度负荷峰值的计算公式。

According to heat load source of die cavity, temperature distribution gradient equations and heat flux equations and the peak value equations of temperature load at die cavity surface have been obtained with research of temperature distribution and transfer laws of die surface by unsteady heat transfer theory.

新闻摘要：根据锻模型腔热负荷来源，通过非稳态传热理论，分析研究了模具工作表面层的温度分布与传递规律，给出了型腔表面温度分布梯度和热流密度公式，并给出了锻模型腔表面的温度负荷峰值的计算公式。

For example, in cases where the target temperature is 60° C., the fan revolution speed, which is shown by a two-dot chain line, does not rise immediately when the actual temperature of the cooling target fluid exceeds the target temperature of 60° C.

例如，在的情况下，目标温度为60 ° C时，风扇转速，这是表现出两个斑点链路线，并没有立即上升时，实际温度的冷却液指标超过目标温度为60 ℃之间，但后，冷却液的目标，极大地overshoots目标温度。

Measures of improving for low temperature toughness by selecting the welding materials and strictly controlling the welding process for welded joints of low temperature low-alloy steel, nickel alloy steel and chrome-nickel austenitic stainless steel for low temperature pressure vessels were summed up.

为了改善工作于低温环境的压力容器用低合金低温钢、镍合金钢和铬镍奥氏体不锈钢的焊接接头低温韧性，而采取改进焊接材料、严格控制焊接工艺的措施。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。