查询词典 tapered

Check out Buck's selection of tapered and pocket sharpeners.

购买巴克精选的锥形磨刀器和口袋磨刀器。

To replace a overflow pipe made from cast iron with the service life of two months, the composite tapered pipe with one end diameter of 180mm and another of 220mm and height of 500mm has been applied in a ore dressing plant for almost one year, and it is still in service now.

某选矿厂使用白口铁溢流管（φ180mm—φ220mm×500mm），寿命为2个多月，改用内衬陶瓷的灰口铁溢流管，已使用了近1年，现仍在继续使用。

In particular, the special-shaped, tapered, spherical roof of the song panel, the board has a ladder leading development capability.

尤其对异形、锥形、球形屋面的曲面板、梯形板有着领先开发能力。

There are several manual steering gears in current use like the rack and pinion type ,the worm and tapered pin steering gear ,and the worm and roller steering gear.

目前使用的手动转向齿轮机构就是有好几种，如齿条齿轮式转向机构、蜗杆斜销式转向机构以及蜗轮滚柱式转向机构。

To cooperate with new and old parts: although standard zero, components, but in between interchangeable in assembly parts, and to make the optimal coordination between trim, still needs a lot of work, such as the gear and rack, boring if after removal of gear various performance indicators are used by detecting without the need to change, and to replace worn rack, rack and rack positioning pin hole on installation bolt holes and should be first, reoccupy hand crossed positioning drills and tapered reamer to match the drill and match hinge, and after the installation of new and old super-modulus gear mesh clearance to achieve technical standards, this work takes about one day.

。新，旧零部件重新配合过程：尽管标准零，部件间具有互换性，但在装配中，要使新旧零部件间的配合达到最佳状态，仍需大量的修整工作，如镗床的齿轮与齿条，若拆卸后齿轮的各项性能指标经检测尚能使用不需更换，而齿条磨损严重需更换，那么齿条及齿条安装面上的定位销孔和定位螺钉孔就需先划线定位，再用手电钻及锥形铰刀重新配钻和配铰，且新齿条安装完毕后与旧齿轮的啮合间隙需达到技术要求的标准，此项工作需时约一天。

To cooperate with new and old parts: although standard zero, components, but in between interchangeable in assembly parts, and to make the optimal coordination between trim, still needs a lot of work, such as the gear and rack, boring if after removal of gear various performance indicators are used by detecting without the need to change, and to replace worn rack, rack and rack positioning pin hole on installation bolt holes and should be first, reoccupy hand crossed positioning drills and tapered reamer to match the drill and match hinge, and after the installation of new and old super-modulus gear mesh clearance to achieve technical standards, this work takes about one day.

。新，旧零部件重新配合过程：尽管标准零，部件间具有互换性，但在装配中，要使新旧零部件间旳配合达到最佳状态，仍需大量旳修整工作，如镗床旳齿轮与齿条，若拆卸后齿轮旳各项性能指标经检测尚能使用不需更换，而齿条磨损厉害需更换，那么齿条嘉逸条安装面上旳定位销孔和定位螺钉孔就需先划线定位，再用手电钻及锥形铰刀重新配钻和配铰，且新齿条安装完毕后与旧齿轮旳啮合间隙需达到技术要求旳标准，此项工作需时约─天。

Cold has two methods: one is the cold-drawing method is to pipe through the tube drawing die, so that tapered pipe, elongation; Another method is to cold-rolling method, it is to Mannesmann brothers invented Meng Hot Rolling Mill of the methods used in cold working.

冷加工有两种方法：一种是冷拔法，就是将钢管通过拔管模拉拔，使钢管逐渐变细、伸长；另一种方法是冷轧法，它是将孟内斯曼兄弟发明的热轧机应用于冷加工中的方法。

"Water connections in heater are 3/4"tapered pipe thread.

&热水器上的水连接管径都是3/4&&锥管螺纹接头。&

"Water connections in heater are 3/4"" tapered pipe thread."

&热水器上的水连接管径都是3/4&&(俗称：6分管)锥管螺纹接头。&

Threaded systems should be made with Schedule 80 pipe only, threaded with an ANSI general purpose tapered pipe thread.

螺纹系统应该只能采用管道壁厚标准Schedule 80管道，按照美国国家标准协会的标准，用于一般用途的螺纹应该是锥管螺纹。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。