查询词典 tack weld

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

In addition, effects of weld heat input on microstructure and performance of the weldjoints are analyzed. The test results indicate that by controlling weld heat input about 16kJ/cm and practicingmulti-layer weld process, the coarse austenitic grains in the weld metal and lumpish ferrite in the heat affectedzone can be avoided so that the microstructure and performance of the weld joints can be ensured.

结果表明，采用多道焊焊接工艺，严格控制焊接线能量在16 kJ/cm左右，可以防止T91钢焊缝区奥氏体晶粒粗大，避免在热影响区出现块状铁素体组织，从而保证焊接接头区具有良好的组织性能。

Stract : The synopsis introduced robot to weld the technique development process, design of weld a small car, and the welder equip the design for have, welding a small car to adopt part to have already have of product, carried on a design towards welding small garage to walk organization, weld the small car will pack Be welding an operation on board, follow behind to weld operation machine of action to carry out to weld relatedly.

摘 要：简要介绍了机器人焊接技术发展历程，设计的焊接小车，及焊接工装设备的设计，焊接小车采用了部分已有的产品，对焊接小车行走机构进行了设计，焊接小车将装在焊接操作机上，跟随焊接操作机的动作来实现相关的焊接。

4 Results of nondestructive test for weld joints shall be graded according to JB 4730. Following requirements shall be met: a For radial test, quality grade of radial transillumination can't be lower than Grade AB, and that of weld joints shall meet table 10; b For supersonic test, approval standard for weld joints are as follows: 1 For weld joints of 100% supersonic test, grade Ⅰ. 2 For weld joints of local supersonic test, grade Ⅱ. c For magnetic particle test and penetration test, grade Ⅰ.

7.5.4 管道焊接接头的无损检测应按 JB 4730 进行焊缝缺陷等级评定，并符合下列要求： a 射线检测时，射线透照质量等级不得低于 AB 级，焊接接头经射线检测后的合格等级应符合表 10 的规定； b 超声波检测时，管道焊接接头经检测后的合格标准如下： 1 规定进行 100%超声波检测的焊接接头 I 级合格； 2 局部进行超声波检测的焊接接头 II 级合格； c 磁粉检测和渗透检测的焊接接头 I 级合格。

Thirdly, with the modified Gurson model of the MARC finite element method soft, the damage behave of the welded joint was simulated. It was found that in the undermatched welded joint, the damage mainly happened in the soft weld line and with the decrease of the weld line抯 width, the damage抯 development was faster. As for the overmatched welded joint, the results showed that the damage mainly happened in the soft base metal and with the increase of the weld line抯 width, the damage抯 development was faster. While the width of the weld line was narrower than three millimeters, the high strength weld line could improve the anti-damage capability of the overmatched welded joint.

通过计算发现在低匹配的焊接接头中，损伤主要发生在低强度的焊缝中，并且焊缝宽度越小，焊接接头的损伤就越严重；而在高匹配的焊接接头中，损伤主要发生在紧临焊缝的强度较低的母材上，随高强度焊缝宽度的增加，焊接接头的损伤发展程度加剧，当焊缝宽度小于3mm时，高强度焊缝的加入对焊接接头能起一个强化的作用，提高了焊接接头的抗损伤能力。

Flat Welding : choice of welding technology, electrode diameter, welding current, welding speed, the length of arc welding, weld process verification; Welding : welding inspection clearance groove, assembly space whether it meets the requirements, positioning it firmly welding, weld around is not oil, rust; Electrode temperature and baking time should be required, the rod removed from the oven. tempreture-constant drum on the electrode, then used as admission; Latin America : welding supply welding thickness, welding levels and electrode type and diameter, skilled welders and other factors, and to select appropriate welding current; fillet weld arc : fluctuations in the point arc weld end, they are advised more than 10 mm, is not hard arc, sparking arc weld zone from the electrode should be started immediately. Component integration and maintaining so-rod pieces have 2-4 mm gap arc.

1.1.2.1平焊：选择合适的焊接工艺，焊条直径，焊接电流，焊接速度，焊接电弧长度等，通过焊接工艺验证；清理焊口：焊前检查坡口、组装间隙是否符合要求，定位焊是否牢固，焊缝周围不得有油污、锈物；烘焙焊条应符合规定温度与时间，从烘箱中取出的焊条，放在焊条保温桶内，随用随取；焊拉电源：根据焊件厚度、焊接层次、焊条型号、直径、焊工熟练程度等因素，选择适宜的焊接电流；引弧：角焊缝起落弧点应在焊缝端部，宜大于10㎜，不应随便打弧，打火引弧后应立即将焊条从焊缝区拉开，使焊条块结合与构件间保持2～4㎜间隙产生电弧。

Flat Welding : choice of welding technology, electrode diameter, welding current, welding speed, the length of arc welding, weld process verification; Welding : welding inspection clearance groove, assembly space whether it meets the requirements, positioning it firmly welding, weld around is not oil, rust; Electrode temperature and baking time should be required, the rod removed from the oven. tempreture-constant drum on the electrode, then used as admission; Latin America : welding supply welding thickness, welding levels and electrode type and diameter, skil led welders and other factors, and to select appropriate welding current; fillet weld arc : fluctuations in the point arc weld end, they are advised more than 10 mm, is not hard arc, sparking arc weld zone from the electrode should be started immediately. Component integration and maintaining so-rod pieces have 2-4 mm gap arc.

1.1.2.1平焊：选择合适的焊接工艺，焊条直径，焊接电流，焊接速度，焊接电弧长度等，通过焊接工艺验证；清理焊口：焊前检查坡口、组装间隙是否符合要求，定位焊是否牢固，焊缝周围不得有油污、锈物；烘焙焊条应符合规定温度与时间，从烘箱中取出的焊条，放在焊条保温桶内，随用随取；焊拉电源：根据焊件厚度、焊接层次、焊条型号、直径、焊工熟练程度等因素，选择适宜的焊接电流；引弧：角焊缝起落弧点应在焊缝端部，宜大于10㎜，不应随便打弧，打火引弧后应立即将焊条从焊缝区拉开，使焊条块结合与构件间保持2～4㎜间隙产生电弧。

Weld -shape( butt weld width, size of fillet weld ) is an indicator of weld features and it also is an important factor of quality welding.

焊缝尺寸(对接焊缝的焊缝宽度、角焊缝的焊角尺寸等)表示焊缝形状特征的指标，是影响焊缝质量的重要因素之一。

Weld-shape(butt weld width ,size of fillet weld)is an indicator of weld features and it also is an important factor of quality welding.

焊缝尺寸(如对接焊缝的焊缝宽度、角焊缝的焊角尺寸等)是表示焊缝形状特征的指标，是影响焊缝质量的重要因素之一。

The results show that mechanical heterogeneity has great influence on the J-integral of welded joint containing transverse crack. The J-integral on the path cross the interface between welded joint and base metal is higher than the J-integral on the paths in the weld metal for undermatched joint,while the J-integral on the path cross the interface between weld metal and base metal is lower than the J-integral on the paths in the weld metal for overmatched joint. Moreover,the difference of J-integral values increases with the increasing of the load and strength mismatching difference and the path-enclosed length of interface between weld metal and base metal.

计算结果表明：力学不均匀性对含横向裂纹焊接接头的J积分有重要影响，低匹配焊接接头中积分路径穿越焊缝与母材界面的J积分值高于积分路径在焊缝内的J积分值，高匹配焊接接头中积分路径穿越焊缝与母材界面的J积分值低于积分路径在焊缝内的J积分值；载荷越大，焊缝与母材的强度差别越大；积分路径中包含的焊缝与母材界面长度越大，J积分的差值越大。

We got alerted a couple of times while we were down south that HETs were on the way to bring us back up north because things were going to go hot again, but it was just rumors.

南下的途中我们不只一次得到警告说重型装备运输车将拉着我们重新北上，因为局势正在变得重新紧张起来，但这只是谣传。

It's the one where they find the ghost in the salt mine.

这一集是演他们在盐矿找到鬼