查询词典 swaged

Expectedly, larger tubes whose ends have been swaged to a smallerdiameter for a short distance can be similarly closed.

同样，大的管子在末端封口形成小的末端，也可以进行类似的封口操作。

The correlation among the percentage reduction, mechanical properties and microstructure of 3 biphase W-Ni-Fe alloys swaged under lower temperature has been investigated.

采用低温旋锻方式，研究了三种钨含量的W-Ni-Fe合金的形变强化过程中形变量、力学性能和显微组织之间的关系。

Some of the forms of rivets are solid rivets with chamfered shanks, tubular or hollow rivets, semitubular rivets, swaged rivets, split rivets, and blind rivets.

对一些表格铆钉与倒角柄，管状或空心铆钉，semitubular铆钉，锤造铆钉，铆钉分裂坚实铆钉和铆钉。

Includes 60'-0 of 1/4 diameter galvanized aircraft cable with swivel hook with swaged ball fitting.

包括带有6英尺长直径1/4英寸的飞机电缆以及可旋转吊钩。

The investigation was made on microstructure,mechanical property and recrystallization behavior of tungsten alloy with different amount of swaged deformation.

对不同锻造变形量的钨合金材料组织、性能及其再结晶行为进行了研究。

Marginal fidelity of four methods of swaged matrix crown fabrication.

粘固对金瓷冠边缘适合性的影响。

Cable ends were swaged with a Nicopress sleeve and heat shrink tubing.

电缆两端分别锤造与nicopress套和热收缩油管。

At assembly, two hardened 416 stainless steel shafts with splines on the inboard ends are swaged into the brass inner disk to become the upper and lower stems.

在组装时，两个配置腔内端口花键的硬化416不锈钢轴模压在内部为黄铜的阀瓣上，构成上部和下部阀杆。

With advanced hose assembly swaged equipments from developed countries,we have imported a series of top-level manufacture equipments, such as UNIFLEX swaged machine , large pressure testbed and cleaning machine of German and Hydralok pipe cutting machine of UK. International famous brand hose and high quality fitting from domestic and overseas are used ,products shall be given to use only if have processed in normative technological process by experienced professional technicians and passed the rigorous quality testing and pressure testing.

公司拥有发达国家先进的软管总成扣压设备，引进了一流水平的德国UNIFLEX扣压机、大型压力试验台、清洗机和英国Hydralok切管机等生产设备，选用国际知名品牌的液压软管和国内外精选的优质接头配合，由经验丰富的专业技术人员按照规范的生产工艺流程制作，经严格的产品质量检验并试压合格后交付使用。

The swaged machine in our company is UNIFLEX H325B of German .with advantages that the swaged dates can be controlled by computer to get accuracy. The biggest size can reached 4 inches and mass production is available.The pipe cutting machine is Hydralok HCC2 of UK, this kind of machine has advantages like high efficiency, good verticality in cutting surface and few dust. Above all make the length of hose assembly more accurately.

公司使用的扣压机是德国的UNIFLEX H325B，它的优势不仅可以电脑控制扣压数据，以达到扣压的精确度，最大还可以扣压到4寸的胶管，并适应大批量的生产；切管机是英国的Hydralok HCC2，这种机型切管快，切面垂直度好，使胶管总成长度更加精确，而且产生的粉尘极少，容易清洁；公司还配备了剥胶机、接头装配机，刻字打标机、大型压力试验台、清洗机等，这些设备确保了加工液压管路总成工序的完整性，为保证产品的质量打下了坚实的基础。

This paper discusses design and realizable methods of remote test output interface from logical design angle.

本文从逻辑设计的角度讨论遥测输出接口的设计及实现方法。

This also 星体投射plies to buildings, structures and geological features.

这也适用于建筑物和地质特征。