查询词典 surfaces

At high photocurrent conditions, the presence of gas bubbles was observed on the surfaces of the Pt electrodes.

在较高的光电流条件下，铂电极表面出现气泡。

The surfaces of the grids were analyzed by x-ray diffraction and x-ray photoelectron spectroscopy.

然后，对样品表面进行了X—射线衍射测量和X—射线光电子能谱的测量。

Photometry involves the measurement of luminous intensities of light sources and of the illumination of surfaces.

测光学则涉及到光源发光强度的测量方法以及表面照度的测量方法等。

Micro-concave-surfaces were fabricated on the surface of a photosensitive glass by focused irradiation of femtosecond laser (with 775 nm-wavelength and 150 fs-pulse duration),heat treatment and wet chemical etching in 8% ultrasonic solution of hydrofluoric acid for 50 minutes at room temperature.

利用聚焦的飞秒激光（中心波长775 nm、脉宽150 fs）照射FOTURAN光敏玻璃，经热处理及浓度为8％的氢氟酸溶液室温腐蚀50 min后，在FOTURAN玻璃表面制作了微凹面。

The process of producing images of objects on photosensitive surfaces.

在感光物质表面生成物体图象的过程。

Considering the horizontal coherency of spatial structures in physiographic fractured surfaces, the Kriging method of geostatistics was introduced to correct the distorted sections of apparent resistivity and phase.

考虑到地学断面的空间结构横向上存在着一定的相关性，引入地质统计学的克里格方法以校正畸变的视电阻率断面和相位断面。

Hole repairing in triangular mesh models and piecewise smooth B-Spline surfaces fitting have been studied in this dissertation.

本文对三角网格模型上的孔洞修补及分片光滑B样条曲面的拟合技术进行了研究。

This uniform resample of data points in rectangular region and fitting of piecewise smooth B-Spline surfaces are explored.

研究了矩形区域内数据点的重新均匀采样以及光滑分片B样条曲面的拟合问题。

When described as a distance of an arc on the engagement pitch circle, it is called "Circumference Direction Backlash", when described as the shortest distance between two opposing tooth surfaces is called "Normal Line Backlash".

当描述为齿间弧度距离时，也叫做"圆周向回程间隙"。当描述为两啮合面的最短距离时，也称作"常规线性回程间隙"。

When No. 3 oil is used, put in 3000rpm, 8. 59Nm, the gear surface has an obvious plastic flow, an obvious groove is found on pitch line of the driving gear , an obvious edge is found on pitch line of the driven gear . The operating surfaces of both driving gear and the driven one is high in smooth finish, no pitting. Through the analysis on the gear surface only based on the gear in experiment with No.

实验的结果为：ISOVG68机械油作润滑油时，在输入3000rpm，5.96Nm时，齿面发现沿节线出现大面积的点蚀，且齿面有塑性变形；以3#油为润滑油时，在输入3000rpm，8.59Nm时，齿面发生了明显的齿面塑性流动，主动轮在节线处出现明显的沟槽，从动轮在节线处出现明显的棱脊，大小齿轮工作齿面均十分光洁，未发现点蚀现象发生。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。