查询词典 surfaces

For obtaining satin-finish surfaces on uneven, round surfaces such as balustrades, columns and grave stones.

在栏杆，圆柱，墓碑及其它雕刻品的粗糙或不平整表面获得缎面丝光效果。

In this study, two models to fit soil three-variable characteristic surfaces of different soils were proposed based on the Brooks-Corey soil water retention curve model. Advantages, disadvantages and application conditions of the two were illuminated. In addition, soil three-variable surfaces measured for packed soil samples through centrifuging and controlling bulk density using paraffin material were used to verify the proposed models.

本文在Brooks-Corey土壤水分特征曲线模型的基础上，提出了两种描述土壤质量含水量、吸力和容重三变量关系的曲面模型，分析了模型的优缺点和适用条件，并采用离心机石蜡控容重法实测了四种质地填装土壤的三变量特征曲面。

By RAIRS results we speculate that multilayer BrCH2CH2Br absorb in trans form mainly and below monolayer BrCH2CH2Br dissociatively absorb on the surfaces in -C-C-Br skeleton lay down on surfaces.

由RAIRS的结果我们推测在乾净的Cu(100)表面上，BrCH2CH2Br的多层分子主要是以trans form吸附，单分子层以下的BrCH2CH2Br则是分解性的吸附在表面上，以-C-C-Br骨架躺下的位向吸附。

The theory of surfaces made a slow start. It began with the subject of geodesics on surfaces.

曲面理论也经历了一个漫长的开端，曲面理论是从曲面上的测地线的研究开始的。

For example,at 20 degree for high- gloss surfaces and 85 degree for low- gloss surfaces .

例如，光泽高的表面用20度；光泽低的则用85度。

This paper is mainly focused on data segmentation and model reconstruction problems in Reverse Engineering fields,The main contents include Sharp Featurebased quadrilateral domain extraction from a mesh model,connectivity between multiple B-spline surfaces,fast algorithm for fitting multiple B-spline surfaces on model with arbitrary topology,setting up a hierarchically structured constraintbased data model and binary cubic interpolation of splines with C~2 connectivity for type-Ⅱtriangulations on rectangular domain.

主要内容包括：网格数据的数据分割及矩形片的提取、多个B样条曲面间光滑拼接、任意模型的多个B样条曲面拟合的分块快速算法、基于二元三次样条函数在TYPE-Ⅱ分割下的曲面重建方法、基于约束和层次结构的模型表示及一个小型逆向工程软件系统的建立等。

DRAFT ANGLES TO BE 1%%176FOR UNTEXTURED SURFACES AND 2.5%%176FOR TEXTURED SURFACES.

草案角度为1％％ 176for untextured表面和2.5 ％％ 176for质感表面。

DRAFT ANGLES TO BE 1%%176FOR UNTEXTURED SURFACES AND 2.5%%176FOR TEXTURED SURFACES.

对于无纹理表面，拔模角度为 1%%176，对于有纹理的表面为

STD-750779-0000 2. DRAFT ANGLES TO BE 1%%176FOR UNTEXTURED SURFACES AND 2.5%%176FOR TEXTURED SURFACES.

对于无纹理表面，拔模角度为 1%%176，对于有纹理的表面为

Light grade - paper backed vinyls, wide width and narrow width, to all surfaces except old painted surfaces.

轻度- 裱糊支持的乙烯基，宽宽度和狭窄的宽度，对所有表面除了旧涂面的表面。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。