查询词典 surface

The total charge volume,surface potential,surface charge density and electric field strength on surface of soil were determined.

并且，已有研究者[4]应用此方法对恒电荷的三种紫色土表面

With the raise of temperature, the surface charge quantity, surface potential, surface charge density decrease sharply.

结果同时也反映了三种紫色土表面与重金属离子之间除了存在静电吸附外还存在专性吸附。

This method can get surface potential and surface charge density without the data of SSA and makes it more easy to measure the surface charge properties.

流动法实验结果比传统方法测定值偏高，而这种差异可能主要来源于传统方法所测定的比表面积偏高。

Surface curvature is used to estimate the geometrical parameters of the surface patch and give qualitative analysis on surface patch.

利用曲率从深度图象中提取出表面的几何参数，对表面作出定量分析。

In constructing the surface enclosing each patch, NURBS (non-uniform rational B-spline) surface is employed to describe a three-dimensional free surface.

在构造表面时，应包括每一个片，NURBS表面被用来描述一个三维自由表面。

Firstly, the quadric surface with three points which doesn't on one line is fitted, and then the tangent plane of this fitting surface is got. Meanwhile, the random tangent plane of surface patch subdivided is got also. Finally, the distance can be obtained through iteration between two tangent planes.

首先对点云数据中邻域不在同一直线的三个点进行局部二次曲面拟合，并求取该拟合曲面的切平面，同时求得细分曲面片任意一点处的切平面，最后在两个切平面上进行点对迭代运算，得到点到曲面片的最短距离。

For 5-Axis Cut Line Surface milling and Swarf milling, the alues are: USE_SURF_NORMS—The surface normal is used in determining the tool axis orientation, that is, any user-specified axis definition proides a localized lead and tilt angle that is applied to the normal of the surface being machined.

对于"5 轴切削线曲面"铣削和"刀侧铣削"，值为：使用曲面法向-曲面法向用于确定刀具轴方向，即，任何用户指定的轴定义都提供应用到加工曲面的法向的定位导引角和倾角。

We construct the algorithm of three-dimensions model surface reconstruction in three stages: first, we use Oct-tree to describe scatter data points in space, second find adjacent points and tangent plane and use the triangulation method to realize 3D surface reconstruction in the end, in research on algorithm of three dimensions model surface reconstruction based on scatter data points.

在"基于散乱数据三维表面算法的研究"这一章中，首先通过八叉树的数据结构的算法对三维散乱数据进行处理，然后再确定邻点和微切平面，最后用三角网格化的方法完成三维物体表面重构。

In the algorithm, tangent plane of the surface at each point is first calculated according to the point and its neighbor points. In an optimized sequence, normal vectors of the tangent planes are oriented to the outside of the surface. Finally, marching cube method is used to output the triangular representation of the surface.

该算法首先根据测点的邻近测点估算曲面在该测点处的法矢，并采用优化的顺序对法矢方向进行调整以使各测点处的法矢都指向曲面外侧，最后用步进立方体算法输出三角网格模型。

Considering that the NURBS has become a standard in CAD/CAGD, we shall investigate the approximation to the solutions of the minimal surface equation with the tensor Bezier surface and B-spline surface.

首先我们讨论极小曲面的分片线性的逼近，由于NURBS已经成为形状描述的唯一工业标准，而且极小曲面本身至少应该是二阶光滑的，因此我们讨论了极小曲面方程的Bezier和B样条逼近。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新