查询词典 surface tangent

The next part of the water ring coincided with the inner surface of the impeller wheel Tangent, water ring coincides with the inner surface of the upper leaves of the top contact (in fact the leaves in the water ring must have the insertion depth).

水环的下部分内表面恰好与叶轮轮毂相切，水环的上部内表面刚好与叶片顶端接触（实际上叶片在水环内有一定的插入深度）。

And it is noted that the velocity field in a hydrocyclone is divided to two areas, i.e. the outer para-free-vortex and the inner para-forced vortex. The boundary surface of the velocity field is the maximum tangent velocity track surface, which is a cylinder when the hydrocyclones structure is reasonable.

分析研究结果表明，旋流器的切向速度场由外部准自由涡和内部准强制涡两个区域构成，其分界面为最大切向速度vtmax的轨迹面，结构设计合理时，此轨迹面为一圆柱面。

Water rings on the part of the inner surface just tangent with the impeller wheel, water ring coincides with the lower part of the inner surface contacts the top le**es (the le**es in the water in fact h**e a certain ring insertion depth).

水环的上部分内表面恰好与叶轮轮毂相切，水环的下部内表面刚好与叶片顶端接触（实际上叶片在水环内有一定的插入深度）。

Liquid layer surface tension draw tight the liquid surface along the tangent

液层表面张力沿曲面的切线分向拉紧液面，形成向心回缩力，是吸气的阻力。

A gear H62 which made in yellow brass with the same mode number m=0.34, 2mm thick and had a center hole, when the gap get C=0.5%t , and punched with compound punching die, and the dimension accuracy reached IT7, the part have a flat surface ,the verticality of tangent plane reached 89.5°, its roughness Ra magnitude are 12.5μm, height of burr are 0.10mm; and the punching part are punched with progressive die, the gap C=7%t , initial accuracy are IT11, and have an more rough surface, even can see the gap with eyes.

例如料厚t=1.5mm的H62黄铜冲裁件，选用C≤40%t单边Ⅰ类小间隙冲裁比选用C≤8%tⅢ类大间隙冲裁，冲件固定误差将加大40%～60%，精度至少降一级。此外，采有无搭边排样，冲件的误差要远大于有搭边排样冲件。无搭边排样冲件。无搭边排样冲件的精度低于IT12级，而多数有搭边排样的冲件精度在IT11～IT9级之间，料厚t＞4mm的冲件，尺寸精度会更低一些。

In each step the tangent plane of limit state surface at the previous iterative point is calculated firstly, and then a line from origin to a point on the plane is determined whose intersection with limit state surface satisfies the requirement of feasible direction and convergence.

算法在每步迭代中先计算极限状态曲面在前步迭代点处的切平面，然后在此切平面上选定一个点，使该点和原点的连线与极限状态曲面的交点满足可行方向和收敛的要求。

Based on the geometric expression of the NURBS curve, a simple and effective method of curve and surface extension is put forward, and the blade surface is then successfully extended with the tangent vector by repeatedly applying the above method.

根据叶片的形状特征，以曲线的几何形式为基础，提出了一种简单实用的曲线曲面延伸方法，实现了切矢量连续的叶片型面的延伸。

Second, a nonuniform bilateral filtering algorithm for point set surface and surface attributes is developed, in which the tangent shift of points is avoided. The algorithm can be applied when points are sampled nonuniformly.

其次提出了基于双边滤波对曲面和定义在曲面上的函数的非一致双边滤波算法，该算法不仅避免了滤波过程中点的切向漂移，而且考虑了点采样的密度使得算法可以适应非均匀采样。

Crack sliding induced microcrack surface normal dilation and normal dilation induced microcrack further self-similar propagation are considered, the ineracting of sliding and propagation is clarified. The fourth-order tangent homogeneous stiffness tensor of shear microcrack is deduced, and at last the constitutive model of low porosity is expressed in increment formulation though unit sphere surface integral.

3在评述当前常用的微裂纹滑移准则的基础上，提出了本文的滑移准则，考虑了微裂纹滑移引起的裂纹面法向膨胀，以及由法向膨胀引起的微裂纹进一步扩展，阐明了滑移-扩展相互影响的细观力学机制。

A gear H62 which made in yellow brass with the same mode number m=0.34, 2mm thick and had a center hole, when the gap get C=0.5%t , and punched with compound punching die, and the dimension accuracy reached IT7, the part have a flat surface ,the verticality of tangent plane reached 89.5°, its roughness Ra magnitude are 12.5μm, height of burr are 0.10mm; and the punching part are punched with progressive die, the gap C=7%t , initial accuracy are IT11, and have an more rough surface, even can see the gap with eyes.

例如料厚t=1.5mm的H62黄铜冲裁件，选用C≤40%t单边Ⅰ类小间隙冲裁比选用C≤8%tⅢ类大间隙冲裁，冲件固定误差将加大40%～60%，精度至少降一级。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了