查询词典 surface resistance

The predicted values of resistance force and power for the conventional surface furrow opener at 100 mm depth and 0.28 m/sec speed were0.51 kN and0.14kW, while at 100 mm depth and 0.92 m/sec the values were0.98kN and0.88kW. At 135 mm depth and 0.28 m/sec speed, the conventional surface furrow opener recorded 0.70 kN and 0.20 kW, while at 135 mm and 0.92 m/sec speed, the values were 1.40 kN and 1.26 kW. The predicted values of resistance force and power for the biomimetic furrow opener surface with UHMWPE tubular section ridges at 100 mm depth and 0.28 m/sec speed were 0.45 kN and 0.12kW, while at 100 mm depth and 0.92 m/sec speed, the values were 0.73kN and 0.66 kW.

对于超高分子量聚乙烯材料仿生脊型非光滑结构表面，当耕深100 mm和耕作速度0.28 m/sec时，预测的仿生开沟器的土壤阻力和动力消耗分别为0.45kN和0.12kW；当耕深100 mm和耕作速度0.92 m/sec时，预测的仿生开沟器的土壤阻力和动力消耗分别为0.73kN和0.66kW；当耕深135 mm和耕作速度0.28 m/sec时，预测的仿生开沟器的土壤阻力和动力消耗分别为0.62kN和0.17kW；而当耕深135 mm和耕作速度0.92 m/sec时，预测的仿生开沟器的土壤阻力和动力消耗分别为0.91kN和0.82kW。

The experimental values of resistance force and power for the biomimetic furrow opener surface with UHMWPE tubular section ridges at 100 mm depth and 0.28 m/sec speed were 0.60 kN and 0.16 kW, while at 100 mm depth and 0.92 m/sec speed, the values were 0.80 kN and 0.72 kW. At 135 mm depth and 0.28 m/sec speed, the biomimetic furrow opener surface with UHMWPE tubular section ridges recorded 0.76 kN and 0.21 kW, while at 135 mm depth and 0.92 m/sec speed, the values were 0.95 kN and 0.85 kW. The predicted and experimental values of resistance force and power for the conventional surface furrow opener were higher than predicted and experimental values for the biomimetic furrow opener surface with UHMWPE tubular section ridges.

对于超高分子量聚乙烯材料仿生脊型非光滑结构表面，当耕深100 mm和耕作速度0.28 m/sec时，实测的仿生开沟器的土壤阻力和动力消耗分别为0.6kN和0.16kW；当耕深100 mm和耕作速度0.92 m/sec时，实测的仿生开沟器的土壤阻力和动力消耗分别为0.8kN和0.72kW；当耕深135 mm和耕作速度0.28 m/sec时，实测的仿生开沟器的土壤阻力和动力消耗分别为0.76kN和0.21kW；而当耕深135 mm和耕作速度0.92 m/sec时，实测的仿生开沟器的土壤阻力和动力消耗分别为0.95kN和0.85kW。

They are FF testing methods, surface treatment technique, evaluation of the properties of surface modification layer, coating induced embrittlement, selection of coating materials, effects of SP and other surface modification on fretting fatigue resistance . A new coating technology combined with shot peening is proved in improving FFR of titanium alloy. The relation between fretting wear and fretting fatigue mechanism of titanium alloy are discussed on the basis of the experimental results. The main contributions are as follows:(1) Shot peening is the most efficient way in improving fretting fatigue resistance of titanium alloys. Working hardening, roughening and compressive residual stress are involved in the shot peened surface.

本文针对上述问题，从影响FF行为的关键环节：FF实验方法、表面处理工艺技术及表层性能评价、镀层引起的钛合金脆化行为、脆化机制及镀层材料的选择、喷丸强化因数和表面涂层对钛合金FF抗力的影响、FF与微动磨损的联系等，深入系统地研究影响钛合金FF抗力的控制因数，探讨FF机理，并通过喷丸形变强化与新型表面镀或渗层合理复合，达到进一步提高钛合金FF抗力的目的。

For the first time, a screw pile and pile driver system for preventing flood and rushing to deal with an emergency was manufactured. The screw piles of the system is different from screw drills used to sap, and it doesn't push soils out. Analyses, including the screw pile's structural strength analysis and the screw blade's welding analysis, were done by ANSYS, which showed that the screw pile's structural strength is enough and that the distort of the screw blade is small. Testing on the screw pile and pile driver system showed that the system performed stably and could meet the need of preventing flood and rushing to deal with an emergency. A mechanics model of interaction of a screw pile and soil was built, and expressions of torque of screw pile's cylindrical part on the condition of screw pile's crew part being driven into soil fully were gained, then the relation of the torque with screw pitch and out diameter of cylinder, which shows the torque decreases with the screw pitch increasing, and that the torque increases with the out diameter of cylinder increasing, which was according with the experiments of the screw pile's being driven into soils, and thus a screw pile with the best structure was chosen. Experiments of bionic surface showed that, on the condition of certain pressure on the surface, the protruding bionic surface can not reduce adhesion and resistance and that the corrugated bionic surface can reduce adhesion and resistance. An orthogonal experiment of the corrugated bionic surface was done with the factors including the width of protrusion, the space between two protrusions, the trolley's velocity and the vertical surface pressure and with the surface frictional coefficient as the experimental target, and some inclusions were drawn that the best combination of the factors was acquired and that the width of protrusion affected the surface frictional coefficient remarkably.

研制了防汛抢险螺旋桩机系统，提高了沉桩作业效率；利用ANSYS对桩体进行整体结构强度分析以及螺旋叶片的焊接分析，表明桩体结构强度足够，焊接过程中，螺旋叶片的变形小；对整个螺旋桩机系统进行试验，表明该系统性能可靠，工作稳定，作业效率高，能够满足防汛抢险沉桩作业基本需要；建立了螺旋桩桩土作用力学模型，得出螺旋桩沉桩过程中螺旋桩螺旋部分完全进入土体时螺旋桩圆柱部分所受扭矩以及扭矩与防汛抢险螺旋桩的螺旋导程和圆柱外径的关系曲线，表明螺旋桩螺旋部分完全进入土体时螺旋桩圆柱部分所受扭矩随着螺旋导程的增大而减小，随着圆柱外径的增大而增大，这与螺旋桩沉桩试验结论相符合，据此优选出最佳结构的螺旋桩；仿生曲面试验表明，尺寸较小的球冠突起型仿生曲面在一定压力作用下未能起到减粘降阻的作用，而尺寸较大的波纹型仿生曲面相对平板具有一定的减粘降阻作用；以波纹型仿生曲面突起宽度、波纹型仿生曲面两突起之间间距、台车的牵引速度以及叶片表面垂直载荷为因素，以曲面摩擦系数试验指标进行正交试验，寻求出在一定试验条件下最佳因素水平组合；波纹型仿生曲面突起宽度在本试验条件下对曲面摩擦系数影响显著，而其它几个因素对曲面摩擦系数影响均不显著；通过波纹型仿生曲面突起宽度和台车牵引速度的单因素试验，表明曲面摩擦系数随着仿生曲面突起宽度的增大而减小，而随着台车牵引速度的变化基本保持不变，和正交试验结果保持一致。

Composed of round door frames, gate, rack , sealing strip, adjustable structure of sealing , this kind of sealing principle is door frame is fixed on square pipe of pool and wall, rack is fixed on door frame and wall, through rack opens and closes till weld block of gate meets with weld block of rack to make sealing surface of gate close to sealing surface of door frame to achieve sealing .Besides , sealing of gate and sealing of door frame are made of inlaid copper which is well resistance ,It makes valve with well sealing ,wear resistance , corrosion resistance, easily operation, convenient installation , long life , wildly usage.

本闸门是由圆型门框、闸板、导轨、密封条、可调整密封机构等部件组成，其密封原理是门框固定于水池圆型管道及墙壁上，导轨固定门框与墙壁上，闸板通过导轨做启闭动作，直到闸板上的锲块碰到导轨条上的锲块，使得闸门密封面紧靠门框上的密封面，从而起到密封效果，另外闸板密封面跟门框密封面都是镶铜材质的，具有耐磨损的特性，使得阀门密封密封性好、耐磨性强、耐腐蚀、操作简单、安装方便、使用寿命长、适应性广等特点。

Composed of square door frames, gate, rack , sealing strip, adjustable structure of sealing , this kind of sealing principle is door frame is fixed on square pipe of pool and wall, rack is fixed on door frame and wall, through rack opens and closes till weld block of gate meets with weld block of rack to make sealing surface of gate close to sealing surface of door frame to achieve sealing .Besides , sealing of gate and sealing of door frame are made of inlaid copper which is well resistance ,It makes valve with well sealing ,wear resistance , corrosion resistance, easily operation, convenient installation , long life , wildly usage.

本闸门是由方型门框、闸板、导轨、密封条、可调整密封机构等部件组成，其密封原理是门框固定于水池方型管道及墙壁上，导轨固定门框与墙壁上，闸板通过导轨做启闭动作，直到闸板上的锲块碰到导轨条上的锲块，使得闸门密封面紧靠门框上的密封面，从而起到密封效果，另外闸板密封面跟门框密封面都是镶铜材质的，具有耐磨损的特性，使得阀门密封密封性好、耐磨性强、耐腐蚀、操作简单、安装方便、使用寿命长、适应性广等特点。

The surface resistance is below 106Ω.

表面电阻值：106 欧姆以下。

A new method and experimental device for measuring microwave surface resistance of high superconducting thin films are presented in this paper.

本文报导一种测量高温超导薄膜微波表面电阻的新方法和测试装置。

Figure 2 shows the surface resistance of paper along with the increase in air relative humidity.

图2暗示：纸的暗不天电阻随着氛围不绝不差湿度的补偿而减小。

The paper summarizes systematically the existing state of the structure of slide plate of turnout at home and abroad, improves and optimizes the structure of slide plate of speed-up turnout against the existing problems of slide plate of speed-up turnout such as failure tightening force, cracks in spring shim and pin, large surface resistance of slide bed-plate, difficulty in gauge adjusting and so on.

本文较为系统地总结了国内外道岔用滑床板的结构现状，针对提速道岔用滑床板存在的扣压力失效、弹片与销钉出现裂纹、滑床台板表面阻力大、轨距调整困难等问题，改进和优化了提速道岔用滑床板的结构。

According to the clear water experiment, aeration performance of the new equipment is good with high total oxygen transfer coefficient and oxygen utilization ratio.

曝气设备的动力效率在叶轮转速为120rpm～150rpm时取得最大值，此时氧利用率和充氧能力也具有较高值。

The environmental stability of that world - including its crushing pressures and icy darkness - means that some of its most famous inhabitants have survived for eons as evolutionary throwbacks, their bodies undergoing little change.

稳定的海底环境─包括能把人压扁的压力和冰冷的黑暗─意谓海底某些最知名的栖居生物已以演化返祖的样态活了万世，形体几无变化。