查询词典 surface of revolution

A slotted concentric cylinder carries a continuous solid wing across and in contact with the interior surface of an ovoid shell, shaped for exact diameter in all directions on the eccentric axis of revolution.

" "开槽同心圆柱体，带有连续固相荣跨越和联系，与内部表面一卵形壳，形状为直径的确切在各个方向上偏心轴的革命。

The abstract lathe is in the machine manufacture uses a most widespread kind of engine bed, mainly uses in processing each kind of rotation surface (for example: In the outer annulus cylinder, the circular conical surface, the ring groove, the solid of revolution formation surface and so on) and the solid of revolution end surface, some lathes also can process the thread.

车床是机械制造中使用最广泛的一类机床，主要用于加工各种回转表面（如：内外圆柱面、圆锥面、环槽、回转体成型面等）和回转体的端面，有些车床还能加工螺纹。

In this paper , unit moving trihedron is first constructed for a point on the surface of a revolution ellipsoid .

以旋转椭球体面上某点为原点建立一个大地坐标单位活动坐标架。

Derives the formulae for calculating the distortion and stress on the acting surface of flexspline load in the drive process of the harmonic gear drive with three-wave wavegenerator;(2) analyzes and compares the performance of plastic and steel products under light load drive and calculates the probably reached limit of drive ratio for both types of flexsplines under the same load;(3) applies the harmonic gear drive with three-wave wavegenerator to the small-sized multiple-revolution electric device of valves by taking into consideration of the low limit of the drive ratio for the harmonic gear drive with three-wave wavegenerator made of plastics, improves the design on the main drive mechanism of the traditional small-sized multiple-revolution electric device of valves, and validates through examples the feasibility for the harmonic gear drive with three-wave wavegenerator made of plastics to be applied to the small-sized multiple-revolution electric device of valves. Finally the author performs calculations on the two types of the flexsplines of the harmonic gear with three-wave wavegenerator by using the finite element method and analyzes the causes for the errors.

本文根据三波谐波齿轮传动的运动变形特点，采用弹性薄壳的力矩理论，推导了三波谐波齿轮传动柔轮载荷作用面上的变形及应力计算公式；分析比较了轻载传动情况下塑料和钢材的性能，计算了塑料制谐波柔轮和钢制谐波柔轮在相同载荷情况下可能达到的传动比极限；对塑料制及钢制三波谐波齿轮柔轮进行了有限元计算，分析了产生误差的原因；针对三波塑料谐波齿轮传动比极限低的特点，将之运用于小转矩多回转阀门电动装置中，对传统的小型多回转阀门电动装置的主传动机构进行了改良设计，并通过实例验证了三波塑料谐波齿轮传动在小转矩多回转阀门电动装置中应用的可行性。

Based on the former drag reduction experiments of the bionic nonsmooth body of revolution models in the lowspeed wind tunnel, the simulation wind tunnel tests at the wind speed of 44 m/s were performed for the body of revolution models with the tail rectangularly disposed by three different nonsmooth structures, such as the convex dome form with the diameter/height of 1.0/0.5 mm, the dimple concave form with the diameter/depth of 1.0/0.5 mm, and the riblet form with the width/height of 1.0/0.5 mm, in contrast with the body of revolution model with smooth surface.

在前期进行的仿生非光滑旋成体模型低速风洞试验的基础上，将非光滑形态在旋成体模型上的排列方式固定为矩形布置，非光滑的尺寸固定为直径或宽度为1 mm，深度或高度为0.5 mm，在风速为44 m/s时，对布置在模型尾部的凸包形、凹坑形和棱纹形三种非光滑模型与表面光滑模型进行了对比模拟试验。

Because the horizontal lathe craft scope is quite widespread, may in the turning the outer annulus cylinder, the circular conical surface, the ring channel, the solid of revolution formation surface, the turning end surface and each kind of commonly used metric system, the British system, the mold notational system, the pitch system thread, but also may carry on drills the center bore, the drill hole, the broaching, reams, work and so on tapping, wrap thread and knurling.

因为卧式车床的工艺范围相当广泛，可以车削内外圆柱面、圆锥面、环形槽、回转体成型面，车削端面和各种常用的公制、英制、模数制、径节制螺纹，还可以进行钻中心孔、钻孔、扩孔、铰孔、攻螺纹、套螺纹和滚花等工作。

By study the method of approximate development of surface of revolution,the mathematiccal model of approximate development,precision analysis and error correction has been gained.

通过对不可展回转曲面近似展开方法的研究，得到了回转曲面近似展开、精度分析和误差矫正的数学模型。

Finally, we give some examples for representing surface of revolution and sphere as rational B-spline patches.

文中附有旋转曲面和球面的生成实例。

Pull command: A bug that caused loops when a curve was pulled to a surface of revolution is fixed.

属性对话框：修正符合物件的材质时作业不正确的错误。

Reformed light MQ6025A universal tool grinder can realize 2-coordinate linkage machining of special type surface of revolution cutting tool.

通过简单改造的MQ6025A轻型万能工具磨床，可实现两坐标联动加工特种回转面刀具。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。