查询词典 surface of contact

This dissertation first puts forward the model of driving force transformation which the contact region of stator and rotor is divided into three relative sliding areas such as braking—driving—braking by means of research on vibration characteristics of USM stator surface points and micro driving course to rotor, this model can explain variation regularity of USM load characteristics, moreover, simplified calculation formula of rotor driving force concerned with stator teeth is set up.

本文通过对行波超声马达定子表面各点的振动特性和定子对转子微观驱动过程的研究，首次提出将定子和转子接触区划分为制动区—驱动区—制动区三个相对滑动区的驱动力转换模型，这一模型能够解释超声马达负载特性变化规律，并建立了计及定子齿的转子驱动力计算简化公式，该式能应用于多于两个定子齿驱动的转子驱动力计算。

To get the steady interface, the ratio of coextrusion flow length to height is at least l-1.5._The role of smooth flow zone is important to reduce the pressure-fall. The higher surface quality of the fluid path can make the velocity field more uniform and the interfacial offset less. However, the layer interface position was almost unaffected by the convergence angle, so for the convenience of die manufacture and extruder\'s collocation, it is fit to make the contact angle as 90°with smooth corner.

在模具结构参数中，共挤出流道的长度和模具壁面光滑程度对界面有重要的影响，根据计算结果得到了方形流道共挤出段长度与高度比的取值范围；而模具入口收敛角对界面的影响不大，在实际生产中为了模具制造和共挤出机布置的方便，可采用圆滑过渡的90°入口角。

It is reported that 70 percent of MPM has had a history of asbestos contact. There is a thin layer of crocidolite in the surface soil somewhere in Da Yao County of Yunnan province. Because the natives don"t know asbestos" hazard, clay containing asbestos was dug in order to make asbestos stoves, build roads, brush walls, combining the crusts destruction, much deforestation makes asbestos explosion .

云南省大姚县某些地区地表中夹着薄薄的一层青石棉，由于当地居民不知道其危害，大量开挖含青石棉的粘土做石棉炉、铺公路、刷墙等，地表破坏，以及大量砍伐森林，造成水土流失，石棉暴露，含棉岩自然风化，雨水冲刷成为天然污染源。

Contact angle ; angle - dependent XPS ; CF4/CH4 plasmas ; decay constant k of surface dynamics

接触角；变角XPS ； CF_4/CH_4等离子体；表面动力学衰减常数k

At least one second phase;wherein the first phase and the second phase have contrasting colors and wherein all of the phases are rheologically equivalent; and b a dentifrice dispensing means wherein the phases are in interfacial surface contact with the adjacent phase prior to extrusion from the dispensing means .

至少一个第二相；其中第一相和第二相具有对比色，并且其中所有的相为流变学相当的；和b洁齿剂分配工具，其中所述相在被挤出分配工具前在分界表面上与相邻的相接触。

Based on the idea of the structure parametric design method, the parametric finite element model of drill chuck with complicated spiral surface character was established.'The related key technologies of drill chuck's strength analysis were discussed and solved, such as the contact analysis parameters selection, the boundary conditions and the load processing, ANSYS command一string building and so on.

本文采用结构参数化设计方法建立了含有复杂螺旋曲面特征的钻夹头参数化有限元模型；探讨和解决了钻夹头夹紧强度分析中夹爪与螺母接触分析参数的选择、约束边界和载荷处理、分析流程文件创建等关键技术问题。

In order to produce the billet without surface defect under high casting speed and to raise the ratio of DHR or HDCR operation and reduce defect ratio of the final products, soft contact EMCC (Electromagnetic Continuous Casting) technique by imposing high frequency electromagnetic field on the molten steel meniscus region has been developed. This technique is used to control the initial solidification of the billet.

为了在高拉速条件下生产出无表面缺陷的铸坯，以进一步增大铸坯HDR或DHCR的操作比率、提高最终产品的无缺陷率，连铸技术工作者开发出利用高频交变磁场对铸坯初始凝固过程进行控制的软接触电磁连铸技术。

Squeeze the two objects contacts, the contact surface embossing on the part of many mutual engagement.

挤垮两个物体接触，接触面的凹凸上的一部分，有很多互相接触。

The surface structure and the hydrophilic property of the grafted BOPP film were studied through FT-IR, ESCA and contact angle measurement.

采用FT-IR，ESCA，试样与水接触角和接枝率的测定探索了电火花用于引发丙烯酰胺在BOPP薄膜表面接枝聚合反应的方法，研究了接枝BOPP薄膜的表面结构和亲水性能。

The new approach of design of high contact ratio of face gear drive with good dynamic performance are based on application of profile crowning for both tooth surfaces and longitudinal crowning for helical pinion surface.

这一新办法的设计的联系比面对齿轮传动具有良好的动态性能的基础上的应用简介加冕为齿面和纵向加冕螺旋齿轮表面。

The labia have now been sutured together almost completely.The drains and the Foley catheter come out at the top.

此刻阴唇已经几乎完全的缝在一起了，排除多余淤血体液的管子和Foley导管从顶端冒出来。

To get the business done, I suggest we split the difference in price.

为了做成这笔生意，我建议我们在价格上大家各让一半。