查询词典 surface of contact

Contact angle between test solvent and filler or polymer matrix by the surface analysis.The surface tension, polar force parameter of the surface tension, apolar forceparameter of the surface tension and polar fraction had been calculated.

通过表面分析的方法，测出参比液在基体与填料表面的接触角e，计算出其表面张力Ys、表面张力的极性分量丫气、非极性分量Y as。

Firstly, to the particulate filled Polyurethane composites, we have detected the contact angle between test solvent and filler or polymer matrix by the surface analysis. The surface tension, polar force parameter of the surface tension, apolar force parameter of the surface tension and polar fraction had been calculated.

通过表面分析的方法，测出参比液在基体与填料表面的接触角θ，计算出其表面张力γ_s、表面张力的极性分量γ_s~p、非极性分量γ_s~d、极性分数P；并由此估算出了基体与填料所形成的界面的界面张力γ_、粘附功W_a、裂纹能γ_G。

Another approach in enhancing the light extraction efficiency of AlGaInP LED was accomplished using a surface roughening process. In this process, the Au(170 nm)/AuBe(260 nm)/Au(170 nm) ohmic contact layers were first deposited on the GaP window layer. After the alloy annealing process (480°C for 10 min), the Be atoms will diffuse into the GaP top layer and form non-uniform clusters. The LED samples were then immersed into a mixture 3H3PO4:1H2O2:1H2O solution for 6 min, resulting in a rough GaP surface. The luminous intensity of the AlGaInP LED can increase from 42 to 50 mcd, that is, an 18% enhancement can be achieved via the present non-photolithography surface roughening process.Keywords: LED, AlGaInP, Cu substrate, Reflector, Surface roughening

在实验的第二部份是开发磷化镓窗口层之粗化制程，我们是藉由正面金/铍欧姆接触电极之熔合制程，使铍扩散至磷化镓层，同时利用铍渗入磷化镓造成之特殊组成，可形成不均匀之蚀刻阻挡，而在磷化镓表面形成粗化，我们发现480℃、10分钟的熔合制程，加上浸泡磷化镓蚀刻溶液6分钟，可将四元发光二极体之发光亮度由42 mcd 提升到50 mcd，经由此无光罩粗化制程可将亮度提升18%，明显提升磷化铝铟镓发光二极体之外部量子效率。

And then switch on the offset printing presses, and tweak the adjustment nut, rubber plastic knife blade slowly to the oscillating roller surface contact, left and right extremes of adjusting screw contact pressure requires uniform, rubber knife and oscillating roll each part can even contact curettement innovativeink across the Board.

然后启不静胶印机，并且拧不静调度螺母，使橡皮胶刀的刀刃迟缓不天向串不朱辊的暗不天隔绝，把握两头的调度螺丝隔绝不张力给求平均，橡皮刀与串不朱辊每一个部位平均隔绝，不妨片面不天刮不兴油不朱。

Surface roughness was measured by a profilometer, SEM was used to characterize surface morphology, and a goniometer was used to evaluate the contact angle and surface energy of the PPy coating.

纯钛表面PPy电活性层的制备与理化性能表征采用水溶液恒电流原位电化学聚合法在纯钛表面制备PPy涂层。

The main results of the investigation are as following:(1) Some important criteria for the design of multi-layer structure are acquired: the ratio of the layer thickness to the contact diameter should be controlled to a value about 0.8; increasing the number of the gradient layers and elasticity modulus of the top layer would benefit to the yield strength and the stress status at the interface.（2）By means of molecular dynamics simulations for a indentation and sliding process, it is discovered that dislocations of 45 direction to the surface occur in the surfaces layer, which is correspond to the direction of the plastic flows observed in the macroscopic continuous medium. The irreversible deformation caused by the dislocation and the atom piles at the surface are responsible for the irreversibility of the force response. They are also the main factors for the friction generation. The temperature and the indentation velocity have significant effects on the deformation behaviors of the material of the surface layer. The yield strength would increase obviously if the indentation velocity is greater than 10 m/s.（3）A method to evaluate the fracture toughness of coating by estimating the crack-density functionβof a Wicker''s indentation was proposed. Meanwhile a new surface treatment technology was developed using non-equilibrium plasma.（4）A MD-FE hybrid method and corresponding software was developed to analysis the tribological behaviors for multiplayer system.

研究主要内容和结果有：（1）得到指导梯度膜设计的几个准则：控制膜层厚度与接触半径比在0.8左右为宜；适当增加梯度层层数和顶层弹性模量，有利于提高抗屈服能力和改善界面处的应力状态；（2）通过对嵌入和滑动摩擦过程的分子动力学模拟，发现表层产生一个与宏观连续介质的塑性流动方向观测一致的45 方向位错；位错造成的不可逆变形和表面的原子堆积，是力的响应不可逆性的原因，也是构成摩擦力的主要因素；温度和嵌入速度对材料变形特性有显著的影响，当嵌入速度大于10 m/s时，屈服强度明显增加；（3）提出压痕裂纹密度系数β半定量判定膜层断裂韧性的方法；并开发出表面强化新工艺；（4）开发出分析表面摩擦学特性的MD-FE复合模拟方法和相应模拟软件。

To understand the effect of structure of riblet surface on properties of wall, the apparent contact angle of riblet surface was measured and drag reducing effect of riblet surface was confirmed by water-tunnel experiment.

为了得到脊状结构对壁面物性的影响，对脊状表面进行了疏水性测试，获得了液滴在脊状表面上的表观接触角，并通过水洞试验验证了脊状表面的减阻效果。

Main job is to guarantee the scraping interaction and equipment on both sides of the friction surface or can obtain higher precision and accuracy, precision and shape accuracy, precision and contact transmission because of good lubrication, manual and repeatedly is worthy, large amounts of wind, time-consuming, scraping the time needed for different devices vary, such as boring slider and slide block wind profiling, between the match before measuring clearance between the original value, and then according to the technical requirement to measure the value of time and scraping scraping, then apply DanFen red on the slider, manual let slip on the slide seat back and forth, they do straight-line movement between full contact and friction, reoccupy scraper scraping friction creates the contact point, so repeatedly, until the technical requirements for the match, single within 2 days, must blow to the boring if all the time to work with wind, a half month is required.

刮削过程。刮削工作主要是为了保证设备相互接触并摩擦的两面间能获得较高的尺寸精度、形状精度、位置精度、接触精度、传动精度和良好的润滑，因是手工操作且需反复配刮，故工作量大，耗时较长，设备不同，刮削所需时间也各不相同，例如镗床上滑座与下滑座间的配刮，刮削前先测量出二者之间原有的间隙值，然后根据工艺要求测算出需刮削值及每次的刮削量，再将红丹粉涂于上滑座之上，手工让上滑座在下滑座上来回做直线运动，使它们之间充分接触和摩擦，再用刮刀刮削摩擦产生出的接触点，如此反复多次，直至技术要求范围之内，单此项配刮需2天左右，若对于整个镗床所有配刮工作的时间总和，则需半个月左右。

B The gear real tooth surface is represented by a sum of two vector function that determine the theoretical tooth surface and the deviations of the real surface from the theoretical one, and the tooth contact analysis of real surface is completed.

将实际齿面表示为理论齿面和偏差曲面之和，进行了实际齿面的轮齿接触分析。

This plant using the most advanced dual-metal composite cold heading machine, cold header relative Operator have more than ten years of practical experience, I also contact electric plant after the introduction of foreign advanced technology of the deal, the deal with a strictly technical contacts, to make contact without corrosion, combined with a more solid surface, the surface is more shiny, all these advantages are a better guarantee my plants to improve the electrical contacts and high quality.

本厂采用国内最先进的双金属复合冷镦机，相对性冷镦机操作工均有十余年的实践经验，另外我厂引进国外电触点后处理的先进工艺，对触点严格的技术处理、使触点无腐蚀性、结合面更牢固、表面更光亮，所有这些优势都较好地保证了我厂对电器触点的完善和高品质。

The labia have now been sutured together almost completely.The drains and the Foley catheter come out at the top.

此刻阴唇已经几乎完全的缝在一起了，排除多余淤血体液的管子和Foley导管从顶端冒出来。

To get the business done, I suggest we split the difference in price.

为了做成这笔生意，我建议我们在价格上大家各让一半。