查询词典 surface element

A series of erosion-corrosion test has been done to J55 steel under the influence of current of gas-liquid phase by indoor self-made devices, and the corrosion mechanism of current of gas-liquid phase to oil pipe's inner surface has been got. The results show that oil pipe's inner surface will be corroded fleetly by liquid medium and corrosion products will form on it. But at the same time, the corrosion products or protective layer will be removed from the inner surface of steel pipes under the alternate impact of high speed gas and liquid flow, and on this bare steel surface corrosion film will form again and be removed again. Thus, by these ways the corrosion is exacerbated. Surface erosion-corrosion failure comes into being with the circulation of this process going on.

本文主要在气液两相流作用条件下，通过室内自制装置，对管材钢J55做了系列冲刷-腐蚀试验，结果表明，气液两相流对钢管内表面冲刷－腐蚀的机理是钢管内表面会受到液体介质的快速腐蚀，生成腐蚀产物，同时钢管金属表面不断被具有高流速的气液相交替地冲击，不断地从金属表面脱去保护膜或腐蚀产物，裸露的钢表面又会被介质快速腐蚀形成腐蚀膜后，再被两相流冲掉，如此反复，造成管内金属表面膜的连续破坏，使腐蚀加剧，最终导致钢铁表面的冲刷腐蚀失效。

Finally, by means of electrometric method, the stress of the exterior surface of the feed inlet was measured. The curvilinear figure of the stress distribution of the exterior surface was drawed and compared with the results of the finite element analysis. The rationality of theory analysis and the reliability of finite element analysis were verified.

最后，采用电测法对进料口的外表面应力进行了实验测量，绘出进料口外表面应力分布曲线并与有限元分析结果对比，验证了理论分析的合理性和有限元分析的可靠性。

And their improved methods were also researched, for example the force density method with the triangle element transformed the three links, surface stress density method, surface stress density method of sub-structure and nonlinear finite element method of little youngs modulus.

并且对它们的改进方法，比如三角形单元转化成三杆单元的力密度法、面力密度法、考虑子结构的面力密度法和小杨氏模量的非线性有限元法进行了深入的探讨。

The kernel point of the mountainous area high dip angle strata 3D seismic data processing is how to solve 3D reflection surface element divergence ,to increase reflection surface element trace gather inphase stack .

山地大倾角地层的三维地震资料处理的核心问题是如何解决3D反射面元发散，增加反射面元内道集同相叠加，而静校正技术和偏移成像技术正是解决这一问题的关键技术。

Four-node degenerated shell element and rigid shell element are used in our FEM model.Updated Lagrange formulation and rate form constitutive equation are adopted to solve the problem of large strain and large rotation in sheet forming process.Sheet metal material property is described by plastic anisotropy yielding model and isotropic hardening model.Master surface-slave surface contact model is used to define the contact between tools and blank.Contact constraints are enforced with a kinematic algorithm and friction stress is computed by Coulomb friction law.Dynamic relaxation method is used to treat springback after forming stroke.

四结点蜕化壳单元和刚体壳单元分别用来建立板和模具的有限元模型；更新Lagrange法和速率型本构关系被用来处理板料变形中的大应变和大转动；材料模型采用塑性各向异性屈服与等向强化模型；通过主从面模型定义板料和模具的接触，接触算法采用运动约束法，摩擦力用库仓定律计算；并利用动力松弛法对回弹过程进行了计算。

There is no difficulty for us to solve N-K problem for submerged bodies by the coupled element method, but for wavemaking problems of the bodies piercing free surface, we get a difficult problem of line integral on the free surface when we solve the boundary value problem in the external region by boundary element method.

对于深潜物体的N—K问题，用耦合元方法求解不存在根本性的困难，但对于水面船波兴波问题，采用边界元方法来处理外域中的边值问题而出现了所谓的自由面线积分问题。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area;2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support;3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier;4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling;5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene PolymerizationIn this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that:1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS;2.co-mlling time had no obvious effect on the texture of support after 12 hours;3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现；3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布；4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒；5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明：1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致；2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响；3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area; 2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support; 3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier; 4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling; 5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene Polymerization In this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that: 1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS; 2.co-mlling time had no obvious effect on the texture of support after 12 hours; 3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现； 3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布； 4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒； 5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明： 1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致； 2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响； 3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

During solidification,α-Al phase nucleates first in the interstices between the short fibers and grows gradually toward the surface of Al2O3 short fibers. The content of Cu and La element around the surface of Al2O3 short fibers increases, both of them enrich almost in the same region, but the content of Cu element in the interstices of short fiber decreases gradually.

结果表明：Al2O3纤维与基体间润湿良好，生成了致密的界面层；在凝固过程中，α-Al相在短纤维间隙中形核并向纤维表面生长，纤维表面Cu和La元素的浓度增大，纤维间隙中的Cu元素的浓度减小。

In this dissertation, first, based on theory of cutting tooth about the gleason spiral bevel gear, the equation of meshing in the process of cutting tooth, the surface equation of generating gear as well as the general tooth surface equation of the double circular arc spiral bevel gear, using GB12759-1991 type of double circular arc gear as a basic gear profile, a three-dimension solid model of double circular arc spiral bevel gear which has the good adaptability was carried out by used of Unigraphics software;Second, by researching of the algorithm about contact and collision as well as various contact types based upon Contacting Finite Element Method, a foundation was laid for selecting the contact type in analyzing contact stress of double circular arc spiral bevel gearing;Finally, through the connection port of PARASOLID between UG software and ANSYS/LS-DYNA software, the three-dimension solid model of double circular arc spiral bevel gearing obtained above in UG was imported into ANSYS/LS-DYNA, a finite element analyzing about contact stress of double circular arc spiral bevel gearing was carried out by applying new loading method.

本文首先基于格利森弧齿锥齿轮加工原理及切齿啮合过程中的啮合方程、产形轮齿面方程以及双圆弧弧齿锥齿轮的齿面方程，选用GB12759-1991型双圆弧齿轮基本齿廓为基准齿形，利用Unigraphics软件的建模功能，绘制了有较好适应性的双圆弧弧齿锥齿轮传动三维实体模型。其次，描述了应用有限单元法进行实体接触与碰撞问题算法的公式，研究了有限元分析中的各种接触类型以及双圆弧弧齿锥齿轮接触应力分析中所选择接触类型的依据。最后，通过UG软件和ANSYS/LS-DYNA之间的PARASOLID接口工具包，将UG软件中得到的啮合齿轮模型导入ANSYS/LS-DYNA有限元分析软件，给出一种新的加载方法，进行了双圆弧弧齿锥齿轮传动的接触应力的有限元分析。

Putt your way through 36 fun-filled holes of minigolf on 3D designed courses with elevated greens, bunkers, bridges and water hazards, among other crazy obstacles.

您的推杆方式，通过36个有趣的填孔迷你的三维设计的课程，以提升绿党，掩体，桥梁和水的危害，除其他疯狂的障碍。

Some participles can be used either as attributes or as predicatives.

有些分词既可当定语用，也可当表语用。