查询词典 surface coating

GSX—1800 hand dryer is made by imported material and temperature - control elements, aluminium - alloy casing and clingy coating finish,artistic and durable ; camber -line surface is a nice decoration and well-set of waterproof; automatic infrared - ray induction , steady capability , quick reaction and powerful blowing rate shows aptness in public places、hotel、office and family.

GSX—1800 干手器采用进口材料及进口温控零件制造，铝合金外壳和坚固的喷涂保护层，美观、耐用；弧面设计，装饰性强和符合防滴水结构要求；红外线自动感应，性能稳定。起动快，风量大，适用于公共场所、宾馆、写字楼、家庭使用。

Look, good texture should be willing to use a suitable sense of the weight, because the surface layer of non-stick coating, it is not appropriate use of clean cloth wire brushing.

选购时，应选用质感好肯有重量感的为宜，因表面有一层不粘涂层，不宜用铁丝类洁布刷洗。

It was recognized that a simple chromate treatment of galvanized products results in the production of a passive film on the surface of zinc coating which inhibits white rust formation.

热浸镀锌镀件上为了防止白锈，一般以铬酸盐处理在表面形成保护膜来抑制白锈的生成。

When weig ht percentage of TiO 2 sol was10%-20%,the coating showed a good hydrophilicity after UV irr adiation for30～60min or sunlight irradiation for2～5hours. The hydrophil ic angle lowered to about 4degree and the surface of coated layer had the featu re of self-cleaning.

在TiO2溶胶质量分数为10%～20%时，该液体在基板上形成的涂层具有很好的超亲水特性，在UV光照射30～60min或阳光照射2～5h后，亲水角可低至4°左右，涂层表面呈现自洁特性。

AlTiN coating has inconspicuous anti-wear effect on carbide.(3) With the introduce of graphite chips bwteen the frictional surface, the effect of graphite chip on the sliding friction and wear behavior of frictional pair was studied. The results show that graphite chips can reduce the coefficient of friction and frictional temperature, and make the coefficient of friction decrease with the decrease of normal load and rise of sliding speed.

在硬质合金微铣刀高速铣削石墨的刀具磨损和破损研究方面，分析了石墨高速铣削过程中的摩擦学条件，揭示了涂层和非涂层硬质合金微铣刀高速铣削石墨的刀具磨损和破损形态及其机理，研究结果表明涂层早期剥落是涂层的早期破损形式，&抛光&磨粒磨损是涂层硬质合金微铣刀在稳定磨损期的主要磨损机理。

TiAl ; cyclic oxidation ; surface modification ; aluminide coating ; pack cementation

TiAl ；循环氧化；表面改性；铝化物涂层；包埋渗

Particles deposited in the alveoli are immediately subjected to coating by surface active lipid materials.

当粒子沉淀到肺泡中时，立刻会遭到表面活性的脂质物质的复盖。

Surface morphology, microstructure and wear morphology of the coatings were investigated using model KYKY-2800 scanning electron microscope modeled. Phases of the coatings were analyzed using model D/max-RA X-ray diffractometer. Microhardness of the coatings was tested using model MH-6 hardness-testing device. The wear-resisting property of coatings was compared with 65Mn steel treated by the quenching and backfiring technology using the home-made abrasion machine. The feasibility was analyzed for reactive electric-spark build-up welding TiN cermet coating to be used for gear shaft restoration.

采用KYKY-2800型扫描电镜观察了堆焊层表面形貌、显微组织和磨损形貌，采用D/max-RA型X 射线衍射仪分析了堆焊层物相，采用MH-6型显微硬度计测定了堆焊层显微硬度，采用自制磨损实验机对比了堆焊层与淬火回火65 Mn钢的磨损性能，分析了电火花堆焊TiN金属陶瓷层用于轴颈修复的可行性。

The results show that with the increasing of oxidation time, the roughness of the coating surface increases gradually, the growth rates of the MAO coatings decrease, the content of calcium increases in proportion to the time, the content of phosphor increases degressively and the relative content of anatase TiO2 first increases, then decreases.

研究结果表明：随着氧化时间的增加，膜层逐渐变得凹凸不平；膜厚的增速变缓；Ca质量分数呈线性增长；P质量分数呈递减式增长；锐钛矿TiO2的相对含量先增长，然后逐渐减少。

Dentiform surface hardness and of requirements in the following table, different heat treatment process of coating thickness determines hardness of roofing is a valid parameter for the corrugating roll.

齿形表面硬度和硬化层深度的要求如下表，不同热处理工艺下完成的镀层厚度决定了瓦楞的硬度，是瓦楞辊的有效参数。

Lugalbanda was a god and shepherd king of Uruk where he was worshipped for over a thousand years.

Lugalbanda 是神和被崇拜了一千年多 Uruk古埃及喜克索王朝国王。

I am coming just now,' and went on perfuming himself with Hunut, then he came and sat.

我来只是现在，'歼灭战perfuming自己与胡努特，那麼，他来到和SAT 。