查询词典 surface coating

Through designing of composition and structure of the bioactive graded coating,innerstress and its distribution in the coating were analyzed and calculated, the resultsshowed that when composition distribution coefficient n was 1.5, a reasonable stressdistribution could be got, that was at the beginning of deposition the suspension containingrichly BG granules was used so that a rich BG granules layer, a good transitional layerbetween BG layer at the bottom and the coating could be obtained at the titanium alloy side,the bottom of the coating; the stress value near the interface and surface and its character,pressure stress or tensile stress, were decided by the character of its composition itself.Changing composition distribution coefficient n could only change the variation tendency ofstress in the coating, but did not change the stress distribution rule in the coating. Thethinner the coating is, the sharper stress variation in the coating is, which does not mean thatthicker coating is better because the thicker the coating is, the little the permitteddeformation of coating is, so the coating thickness should be thinner, for example, about50μm for bending applications, but for applications only bearing pure shear stress, such asroot of tooth implant, the coating can be thicker little, for instance, about 80～100μm. The study on electrification characteristic and electrophoresis deposition of HAand BG granules in aqueous and non-aqueous solution system found that EPD almost didn'toccur in aqueous solution system. However, because HA granules take position charges inabsolute alcohol, a homogeneous EPD be carried out on the cathode titanium alloy slice, but taking negative charge in absolute alcohol the BG granules not be deposited on the cathode. A guided HA crystallizing, 100～300nm, on surface of the BG granules be realized by metathetical reaction, which cover BG granules with HA microcrystals and make the covered BG granules taking position charges in absolute alcohol, sequentially realize the EPCD of the BG and HA granules on the cathode, so it is feasible to make a titanium alloy/BG/HA bioactive graded coating by making use of EPCD technology. The corrosion experiment of rich boron bioglass coating and plasma spray coating showed that split phase, rich boron and rich silicon phase, occurred during its preparation. In basic medium the corrosion behavior of 〓 BG coating showed uniformity corrosion, the corrosion mostly occurred at rich boron phase area, therefore batch formula design of BGshould avoid the occurring of split phase. The corrosion appearance of plasma spray coatingappeared a non-uniform corrosion, mostly occurred at the edge of the laminated HA moltendrops, and emerged an accelerated corrosion tendency, which will easyly lead to corrosioncrackles extending to the interface and the happening of osmotic interfacial corrosion, thatmay be one of the major reasons leading to the coating cracking-off in the later period. Thetesting results of thermal expansion coefficient of 〓 and 〓BG showed the thermalexpansion coefficient of 〓 BG matched with that of titanium alloy better, and 〓 BG couldsinter with titanium alloy into densification enamel layer at low temperature (720℃).

将Ti6Al4V合金在1000℃下进行真空热处理会降低其力学性能，且合金内的V元素会向表面富集，因此，钛合金真空热处理和表面涂层的烧结温度不能过高，即应低于其相转变点；通过对生物活性梯度涂层的组成和结构的设计，分析和计算了梯度涂层内的应力大小和分布，结果表明：对于本研究，当成分分布系数n=1.5时，可以获得较合理的涂层力学性能，即在沉积开始时，采用富含BG颗粒的悬浮液，以便在钛合金侧获得同底层BG有良好过渡的富BG涂层；梯度涂层界面和表面的应力大小、性质由材料组成本身的性质决定，改变成分分布系数，只能改变涂层内应力变化的趋势；涂层的厚薄不影响涂层内的应力分布规律，但涂层越薄，涂层内的应力变化越快，但这并不意味着涂层越厚越好，因为涂层越厚，涂层允许的变形越小，对于应用于弯曲受力部位的涂层而言，涂层应薄一点为好(50μm)；而对于仅纯受剪切应力的部位，如牙根种植体，涂层可适当加厚(80～100μm)；通过对HA和BG颗粒在水溶液体系和非水溶液体系中的带电特性和电泳沉积的研究发现，它们在水溶液体系中很难发生电沉积；在无水乙醇溶液中，HA颗粒带正电，可在阴极钛合金片上发生均匀的电泳沉积，而BG颗粒则带负电荷；利用复分解反应法，可以制得100～300nm的HA，通过诱导HA在BG颗粒表面结晶，可对BG颗粒进行表面包覆，获得了被HA包覆的BG颗粒，改变了BG颗粒表面的带电特性，使BG和HA颗粒在无水乙醇中均带上正电荷，从而实现了HA和BG颗粒在阴极上的共沉积。

The basic concepts of coatings function, composition, classification. Various coatings: drying oil, rosin and lacquer, alkyd resin and polyester coating, amino resin coating, acrylic acid resin coating, epoxy resin coating, polyurethane coating, elementary organic resin coating. Several new coatings: high solid-constituent coating, water soluble coating, powder coating, light-sensitive coating, anti-corrosion coating, flame-retarded coating, anti-contamination coating, color changing coating, conductive coating and magnetic coating, aeroplane and aerospace dope.

涂料的基本概念：涂料的功能、基本组成、分类；各种涂料的制造及应用：干性油、松香与大漆，醇酸树脂与聚酯涂料，氨基树脂涂料，丙烯酸树脂涂料，环氧树脂涂料，聚氨酯涂料，元素有机树脂涂料；几种新型涂料简介：高固体分涂料，水性涂料，粉末涂料，光敏涂料，防腐蚀涂料，防火涂料，防污涂料，变色涂料，导电涂料和磁性涂料，航空航天特种涂料。

In addition, some modifications on several computational methods are also presented. Using LMTO method the electronic structure of several systems are studied, and some results are obtained. They are: The ideal Nb (100) surface has three surface states, the multi-layer relaxed surface has two surface states. The surface energy of the ideal surface is higher than that of the relaxed surface, that means that the multi-layer relaxed surface is more stable than the former one, which supports the LEED results. The mono-layer relaxed Ag (111) surface is the most stable one among several" stable surface models"presented by several researchers. The surface energy of Ag (111) surface is higher than that of surface Ag (001), which supports some experimental results such as different reaction rate at different surface orientations for the same material. The surafce states of Si (111) surface not only locate near the Fermi level, but also in the valence band, which agrees well with Cohen's conclusion. Si (111)-H is an effective model for analysing the surface states and H adsorbed on the back surface is a good method for improving the convincingness of the results obtained on thinner slab models. The surface stability depends on three different kinds of MoSi〓(001) surfaces, the surface with mono-layer Si is the most stable one, and the surface with Mo at the first layer is the most unstable one among them. These are consistant with the Kemoda's experimental results. The valence bands of clean or K adsorbed CdTe (111) surface agrees well with the synchrotron radiation studies. The surface of CdTe (111) consists of four kinds of surface models which show different surface electronic structures and different surface structure stabilities. The conclusion agrees well with Wu's experimental work. The different absorbed alkali metals on the CdTe (111) surface give different adsorption characteristics which have relations not only with the valence electrons, but also with the core ones of the alkali metals. The electonic structures of Si-C alloys are different from that of Si-Ge alloys, and the energy band gaps of Si-C alloys do not increase linearly with Carbon concentration, our conclusion supports Alexander's results, but conflicts with Soref's one.

现分述如下： LMTO方法及其应用方面：1）通过对Nb（100）表面电子态分析发现清洁理想表面有三个表面态，多层弛豫表面有两个表面态；表面能大小说明多层弛豫表面更稳定，支持了LEED结果。2）通过对采用不同方法获得的几种不同Ag（111）表面稳定结构的表面能计算分析，给出了单层弛豫表面为Ag（111）表面的最稳定结构；从Ag（111）单层弛豫表面和Ag（001）表面的表面能比较，发现了Ag（001）表面表面能要比Ag（111）小的，表明了同种物质不同表面取向将表现出不同物理、化学性质，这是与实验中得出的结论是吻合的，3）通过对Si（111）表面态分析，不仅发现了Si（111）表面不仅具有居于费米能级附近的悬挂键所对应的表面态，而且还有很多表面态位于价带能量范围内，与Cohen等结果一致，H饱和slab模型背表面相当于增加了slab层的厚度，是一有效的变相增加slab层厚的方法，弛豫表面较清洁理想表面价带谱们低能端的少许移动，预示着总能降低，说明弛豫表面较清洁理想表面稳定。4）MoSi〓具有三种表面，从费米能级上态密度值大小得到单层Si表面最稳定，Mo原子为表层原子的表面最不稳定，双层Si原子表面居中的结论，这与Kemoda等人实验结果是一致的。5）通过对CdTe（111）表面表面电子态、表面结构稳定性及表面H、碱金属吸附的电子结构系列研究，不仅得出了CdTe（111）清洁及碱金属K吸附价带谱与同步辐射光电子谱相吻合的结果，而且发现了CdTe（111）表面具有四类不同原子近邻特征，表现出四类不同的表面结构及电子结构特征：不同表面态分布、不同的表面结构稳定性（表层原子与次层原子成三键有一悬挂键的表面要比表层原子与次层原子成一键有三悬挂键稳定（与Wu等人实验结果一致））、不同的H吸附特性。

The company's main products: color detection instruments: Glossiness Miriam, Miriam color spectrophotometry, standard light source for color light box, transmissioní°Miriam, Miriam orange peel, fresh young tester; surface coating physical properties testing instruments: Coating thickness, wet film thickness, temperature tracker, surface humidity instrument, dewpoint meter, roughness instrument, electric spark pinhole leak detectors; Detect mechanical properties of surface coating equipment: zoned grid, and pencil hardness tester , impact tester, hardness testing sticks, Latvia Law / hydraulic adhesion tester, abrasion tester, cylinder / cone bending tester, cups sudden device, surface tension instruments, scratch pen, indentation hardness tester, etc.; paint coating equipment dedicated category: fineness board, drying time recorder, wet adhesion tester, paint ohmmeter, PH, the coating device, mixer, bead mill, mixer, spray gun, putty detector Miriam, white tester, iron cobalt colorimeter, moisture titrator; viscosity-type equipment: Viscosity Cup, density cup, bubble viscosity tube viscometer, infiltration cup rheometer, viscosity units conversion meter; laboratory standard consumables: Mitsubishi pencil tests, 3M adhesive tape test, RCA tape, rubber, the hiding power test paper for color tubes, microscopes dedicated LED ring light source, transfer ink knife and ink scraper, brush, Color Card, gray cards, zirconia beads, glass beads, pieces of cement mortar, the standard of fly ash, the standard viscosity fluid, stopwatch, chemical industry-standard compilation of manuals, paint paint testing manual; test standard Material: tin plate, steel plate, aluminum sheet, asbestos-cement pressure plate, Eterpan, glass, maple panels, MDF, copper film, polyester film, copper; measuring meter and optical instruments: digital calipers, micrometer, dial gauge a high scale, depth gauge, thickness gauge, diameter gauge, gauge block, magnifiers, microscopes, projectors, video measuring instrument; environmental test equipment: oven, constant temperature and humidity box, hot and cold circulating water bath, salt spray test chamber, high temperature resistance furnace, fluorescent UV aging chamber, xenon lamp aging chamber; electronics equipment: infrared thermometer, multimeter, clamp sheet, thermal imager, temperature and humidity meter; anti-static instruments: static tester, surface resistivity device, flat-panel monitor, anti-static footwear tester, wrist strap tester, body Tester; other types of instruments and equipment: torque tester, temperature and humidity recorder, push pull, the vibrometer, speed instrument, analytical balance, industrial Scale Units, dust particle counter, X-ray fluorescence coating thickness measurement and elemental composition analyzer, and so on.

公司主营产品：外观颜色检测仪器：光泽度仪、分光色差仪、标准光源对色灯箱、透射雾影仪、桔皮仪、鲜映性测试仪；表面涂层物理性能检测仪器：涂层测厚仪、湿膜测厚仪、炉温跟踪仪、表面湿度仪、露点仪、粗糙度仪、电火花针孔检漏仪；表面涂层机械性能检测仪器设备：划格器、铅笔硬度计、冲击试验仪、硬度试验棒、拉脱法/液压式附着力试验仪、耐磨耗试验机、圆柱/圆锥弯曲试验仪、杯突仪、表面张力仪、划痕笔、压痕硬度计等；涂料油漆类专用仪器设备：细度板、干燥时间记录仪、湿附着力耐擦洗试验仪、油漆电阻计、PH计、涂膜器、混合机、珠磨机、搅拌机、喷枪、腻子测定仪仪、白度仪、铁钴比色计、水份滴定仪；粘度类仪器设备：粘度杯、密度杯、气泡粘度管、粘度计、渗透杯、流变仪、粘度单位换算计；实验室标准消耗品：三菱测试铅笔、3M测试胶带、RCA纸带、橡皮条、遮盖力测试纸、对色灯管、显微镜专用LED环型光源、调墨刀、墨铲、狼毫刷、色卡、灰卡、锆珠、玻璃珠、水泥砂浆块、标准粉煤灰、标准粘度液、秒表、化学工业标准汇编手册、涂料油漆测试手册；测试级标准基材：马口铁板、钢板、铝板、石棉水泥加压板、埃特板、玻璃板、枫木面板、中纤板、紫铜片、聚酯膜、铜棒；量具量仪及光学仪器：数显卡尺、千分尺、千分表、高度尺、深度规、厚度规、内径规、量块、放大镜、显微镜、投影仪、影像测量仪；环境测试设备：烘箱、恒温恒湿箱、冷热循环水浴、盐雾试验箱、高温电阻炉、荧光紫外老化试验箱、氙灯老化试验箱；电子类仪器：红外测温仪、万用表、钳形表、热像仪、温湿度仪；防静电仪器：静电测试仪、表面电阻仪、平板监测仪、防静电鞋袜测试仪、手腕带测试仪、人体综合测试仪；其他类仪器设备：扭力测试仪、温湿度记录仪、推拉力计、测振仪、转速仪、分析天平、工业台秤、尘埃粒子计数器、 X-射线荧光涂层测厚和元素成分构成分析仪，等等。

The weight percentage for the components of the hyaline coating is as follows: SiO2 45 to 54 percent, B2O3 15 to 20 percent, one or more of Na2O, K2O and Li2O, 10 to 24 percent, one or more of TiO2, ZrO2 and ZnO, 6 to 18 percent , and the rest is one or more of CaO, MgO and CeO2. Firstly, the glass powder is mixed with the mill additions to be pulped and then plated on the surface of titanium or the titanium alloy. After being dried, the surface of titanium or the titanium alloy is directly used for a thermal hydrogen treatment or smelted at a temperature of 900 to 1, 000 DEG C for 15 to 30 minutes and then a hyaline coating with a thickness of 20 to 70 micrometers is formed on the surface of titanium or the titanium alloy; secondly, titanium or the titanium alloy plated with the coating is conducted a thermal hydrogen treatment. After the treatment technique is finished, the coating flakes off automatically in the process of cooling; and finally, a surface treatment is supplemented to meet the requirement of the workpiece surface.

该玻璃质涂层成分按重量百分比：45-54SiO2，15-20B2O3，10-24Na2O、K2O、Li2O中的一种或多种，6-18TiO2、ZrO2、ZnO中的一种或多种，余量CaO、MgO、CeO2一种或多种，将玻璃粉与磨加物混合制浆并涂覆在钛或钛合金表面，干燥后直接用于热氢处理，或在900-1000℃下熔烧15-30min，在钛或钛合金表面制得20-70微米玻璃质涂层，随后将制有该涂层的钛或钛合金置于氢气气氛下进行热氢处理，处理工艺结束后，涂层在冷却过程中自剥落，最后辅以表面处理即可满足工件表面要求。

BGB-D Series High Efficiency Coater is mainly used for tablet, pellet, candy to carry out organic film coating, water soluble film coating, slow and control releasing coating, dropping pellet coating, sugar-coating and chocolate, pharmaceutical and foodstuff industry. It is electromechanical integration coating equipment and conforms to the requirement of GMP.

BGB系列高效包衣机主要用于制药及食品工业，是片剂、丸剂、糖果等进行有机薄膜包衣、水溶薄膜包衣、缓、控释性包衣、滴丸包衣、糖衣包衣及巧克力、糖果包衣的一种高效、节能、安全、洁净、符合 GMP 要求的机电一体化的包衣设备。

In this thesis, the research about surface modification of titanium alloy was carried on starting with improving stability of calcium phosphate biomedical coating by force of chemical treatment, Physical Vapor Deposition of titanium metal at high temperature and Electrophoresis Codeposition and sintering technology of the coating. By way of the studying of graded design of microstructure and composition of coating and EPCD and sintering technology, a systemic technology by which a calcium phosphate graded ceramic coating was prepared and sintered rapidly on the surface of a complex shaped product was obtainedand a high function titanium alloy/bioglass/hydroxyapatitegraded coating wasdeveloped.

本文从改善钛合金表面钙磷生物涂层的稳定性入手，采用化学处理、高温真空镀钛和电泳共沉积--烧结等技术对钛合金的表面进行了改性的研究，通过对涂层的结构和组成的梯度设计和EPCD--烧结技术的研究，获得了较系统的能在复杂形状的制品表面涂覆钙磷梯度涂层及其低温快速烧结技术，并研制出了高性能的钛合金／生物玻璃／羟基磷灰石梯度涂层。

There are series of papers studying the solvability of an incompressible, viscous, instationary fluid contained in a domian bounded entirely by a free surface. In 1977, Solonnikov proved its local solvability in a Holder space for any initial date but without surface tension. In 1984, he considered the same problem in a Sobolev space with surface tension being taken into account. In I992, Mogilevskii and Solonnikov treated the same problem in a Holder space, where the coefficient of surface tension is not a constant. There are also short-time existence results for the solvability of an incompressible, vicous, unsteady fluid bounded above by a free surface and below by a fixed bottom which approach horizontal planes at infinity. In 1981, Beale proved its local solvability in a Sobolev space for any initial date but without surface tension. In 1983, Allain were concerned with the same problem in R〓 with surface tension but under the assumption that the initial fluid domain was near a horizontal strip. In 1987, he obtained the same result without the preceding assumption. In 1996, Tani solved the same problem in R with surface tension. For the solvability of an incompressible viscous instationary fluid in Ω R bounded inside by a free surface S and outside by a rotating boundary S, in 1995 Ciuperca proved its local existence in a Sobolev space for any initial date but without surface tension. In this paper, we consider the same problem with surface tension.

对于边界完全是由自由边界组成的有界区域中粘性不可压流体的非定常运动问题，Solonnikcv于1977年在忽略表面张力情况下证明了初值问题小时间解在Holder空间的存在性，于1984年在有表面张力情况下证明了初值问题问题小时间解在Sobolev空间的存在性，Mogilevskii和Solonnikov于1992年在表面张力系数可以不是常数情况下证明了初值问题小时间解在Holder空间的存在性；对于上面是自由边界、下面是固定边界且两边界在无限处趋于水平的无限区域中粘性不可压流体的非定常运动问题，Beale于1981年在忽略表面张力情况下证明了初值问题小时间解在Sobolev空间的存在性，Allain于1983年在有表面张力情况下证明了R中初值问题小时间解在Sobolev空间的存在性，但其中假定初始区域近似是个水平条，他于1987年去掉了这个假定得到同样的结果，Tani于1996年在有表面张力情况下证明了R中初值问题小时间解在Sobolev空间的存在性；对于R中内面是自由边界、外面是旋转边界S的有界区域中粘性不可压流体的非定常运动问题，Ciuperca于1995年在忽略表面张力情况下证明了初值问题小时间解在Sobolev空间的存在性，本文考虑了在有表面张力情况下初值问题可解性问题。

We have studied the micro-structures of trumpet shells,actinia,skin and bamboos, and the bionic design principles and methids for integrated coatings, which inclde gradient coating,duplex coating,composite coating,hybrid coating,super lattice coating, were presented by this group.

研究了海螺壳、海葵、荷叶、皮肤与竹等的微结构，提出了整合涂层（包括梯度涂层、二元涂层、复合涂层、混合涂层、超晶涂层）的仿生设计原理和方法。

Field experiment showed that coating agent with uniconazole (No2 uniconazole seed-coating agent) could significantly defend cucumber seedlings agaist damping-off, inhibit vertical growth and strengthen in thickness of young seedlings. It could blossom early, significantly increase fruit numbers per plant and yields of early stage and total yield. After coating cauliflower seeds by No2 uniconazole seed-coating agent, the uniconazole coating did not affect emergence rate, reduced damping-off disease incidence, increased stem diameter and fresh weight of seedling underground parts.

大田栽培试验发现：烯效唑包衣能显著防控黄瓜苗期猝倒病，抑制瓜苗纵向生长和促进幼苗加粗，使植株开花提早，包衣后黄瓜单株结瓜数提高，前期产量和总产量均显著提高；烯效唑包衣花椰菜使其出苗时间略有延长，但对出苗率无明显影响，包衣后的幼苗猝倒病发病率显著降低，叶色明显加深，幼苗茎粗和地下部鲜重显著增加，包衣的植株现蕾期提早，花球单重显著增加且表现出一定的增产效应，但试验的两品种间存在一定的差异。

Through comparing with the results by simulation to study the effects of theprojectile"s final velocity, the angle of rotation and the ballistic trajectory"s migration withdifferent projectile"s rotating speeds, different target"s moving speeds and differentpenetration angles.

通过比较数值模拟的结果来研究不同弹头转速、目标速度、侵彻角对侵彻过程中弹头最终速度、翻转角度和弹道偏移的影响。

I love stationery and all the accoutrement of writing.

我爱文具以及所有的书写的工具装备。