查询词典 superheat

B Superheat steam and reheat steam's water spray attemperator

c启动旁路系统、管道及疏水

By optimizing such process as refining dreg series and deoxidizing,mode of adding slagging raw materials,blowing Ar system,preventing nitrogen adding in refining process,adopting such process measures as controlling degree of superheat of smelten steel strictly,selecting suitable pulling speed and colling water quantity,using electromagnetism stir in continuous casting,the center carbon segregation index is at about 1.04 basic...

通过对精炼工序中精炼渣系和脱氧工艺选择、造渣原料的加入方式、吹氩制度、防止增氮等工艺的优化，在连铸中采用严格控制钢水过热度、选用合适的拉速和冷却水量、使用电磁搅拌等工艺措施，中心碳偏析指数集中在1.04左右，夹杂物尺寸变小、数量大为减少，疏松和缩孔均降低到0.5级以下，线材面缩率达到34%以上，大部分为41%~44%，索氏体体积分数达到91%，可顺利拉拔至0.3 mm。

Continuous casting ; continuous forging ; fow superheat ; casting

连铸；连续锻压；低过热度；浇铸

Typical results of the limits of superheat and su p er-depressurization for methane and propane are given,and the critical liquid st orage conditions that can lead to limits of super depressurization are analysed.

以 甲烷和丙烷为例给出了过热极限和过减压极限的典型计算结果，分析了可能使液体达到过减压极限的储存条件。

However, a major advantage of superheat in g steam is that for in creas in g cycle temperature and pressure, the exhaust wetness in the turb in e can be ma in ta in ed with in the physical limits.

然而，过热蒸汽的一个主要优势，就是在增加循环的温度和压力的同时，汽轮机的排气湿度可以保持在物理极限内。

A low superheat wall temperature area occurs during the nucleating, and it is larger than the bubble radius.

空穴成核过程中形成的低过热区域超出了气泡直径大小，影响因数在1.3-1.8范围内变化。

To solve the problem of superheat and slow warm-up in the transportation of automobiles,we refits the engine with electric control pump.

针对当前汽车运输中普遍存在的预热缓慢和过热现象，在汽车发动机上进行了电控冷却水泵的改装试验，缩短了预热时间，避免了过热现象的发生。

With the aid of cooling water optimization offline, a new dynamic control model based on optimized relation among speed, superheat and cooling water is obtained considering superheats effects on temperature field.

在实现二冷水量离线优化的基础上，分析了钢水过热度对铸坯凝固过程的影响，并通过数据拟合的方法得到了一种基于拉速—过热度—水量最优关系方程的动态控制模型。

Comb tenoning machine Merit:①The this aircraft uses the straight line guide rail, the precision bearing, the operation is facile;②Has the structure compact, does not fill saws the froth, the precision high, the work table area big, the life long and so on the characteristics;③Has the air operated card functions and so on tight, feed control, auto-stop, automatic rejected material;④Is equipped with the electrical machinery superheat automatic protector and stops the switch anxiously, after the emergency stop the air cylinder may lock automatically;⑤Uses in constructing the profession woodenly only then (below 15*15cm), zygote board docking enhances efficiency 40% compared to the similar product.

梳齿开榫机优点：①本机使用直线导轨、精密轴承，操作轻便；②具有结构紧凑、不塞锯沫、精度高、工作台面积大、寿命长等特点；③配有气动卡紧、自动送料、自动停机、自动退料等功能；④设有电机过热自动保护器和急停开关，紧急停车后气缸可自动锁紧；⑤用于建筑行业的方木（15*15cm以下）、合子板的对接比同类产品提高效率40%。

SnAgCu lead-free solder powders were prepared by close-coupled gas atomization. The effects of gas atomization pressure and melt superheat on the powder size and morphologies were investigated.

摘 要：采用紧耦合气雾化法制备SnAgCu无铅焊料合金粉末，研究雾化压力和熔体过热度对粉末粒径和形貌的影响。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。