查询词典 suction

Figure 1 is the pump suction and exhaust rotor is located just off the termination of position, suction ports and exhaust ports have been sealed rotor sidewall.

图 1 是泵转子刚好位于吸气和排气终止位置，吸气口和排气口被转子的侧壁封住。

Figure 1 is the pump in the suction and exhaust of the process, pump suction chamber with the rotor rotation, the volume gradually increases, inhalation of gas; while the exhaust chamber volume is gradually reduced, the gas is compressed, thereby exhaust gas.

图 1 是泵在吸气和排气的过程，泵吸气腔随着转子的旋转，容积逐渐增大，吸入气体；而排气腔容积则逐渐减小，对气体进行压缩，从而排出气体。

When the pump is installed on the position higher than the liquid level, it is necessary to mount a foot valve on the end of the suction pipe and its throat area should be 50% larger than the sectional area of the suction pipe.

泵安装在高于液面位置时，应在吸入管端装底阀，底阀喉口面积应大于吸入管截面积的百分之五十。

When the pump is installed on the position higher than the liquid level, it is necessary to mount a foot valve on the end of the suction pipeits throat area should be 50% larger than the sectional area of the suction pipe.

泵安装在高于液面位置时，应在吸入管端装底阀，底阀喉口面积应大于吸入管截面积的百分之五十。

Results102 patients were cured by suction clinically;4 patients were cured by two suctions;4 patients by suction with operation.

抽吸术可能并用灌洗、挤压或引流等外科技术。

Constructing model apparatus system of bell-like suction box, the outlet section velocity distribution was measured by probe under various suction open heights.

以流道出口速度均匀度、速度加权平均角、水力损失大小为评价目标函数，研究了钟形进水流道不同喇叭口悬空高度的内流场特征和水力损失特性，提出了喇叭口悬空高度的合理取值范围。

Aimed at the shaking problem at the moment of high speed paper feeding by paper separation suction nozzle of feeder of the press , a set of inverse seeking designing method for the suction nozzle of paper separation mechanism was provided.

针对印刷机飞达分纸吸嘴高速输纸时的抖动问题，提供了一套分纸吸嘴机构反求设计的方法。

Aimed at the shaking problem at the moment of high speed paper feeding by paper separation suction nozzle of feeder of the press, a set of inverse seeking designing method for the suction nozzle of paper separation mechanism was provided.

针对印刷机飞达分纸吸嘴高速输纸时的抖动问题，提供了一套分纸吸嘴机构反求设计的方法。根据实测凸轮廓线离散坐标，利用样条插值法得到了实际廓线的解析方程；构建了分纸机构运动反求的数学模型，得到了从动件及分纸吸嘴的运动规律。

Suction superheat control system consists of electronic expansion valves, pressure sensors, temperature sensors, controller, working hours, the pressure evaporator outlet pressure sensor P1, temperature sensors compressor suction superheat will be passed to controller, controller After signal processing, followed by the output commands acting on the main electronic expansion valve stepper motor to open the valve to the desired location.

吸气过热度控制系统由电子膨胀阀、压力传感器、温度传感器、控制器组成，工作时，压力传感器将蒸发器出口压力P1、温度传感器将压缩机吸气过热度传给控制器，控制器将信号处理后，随后输出指令作用于电子膨胀主阀的步进电机，将阀开到需要的位置。

Bellows Gate Valves However, in large differential pressure operating conditions, evaporation pressure has eased, the evaporator load requirements of the fluid volume decreased, but the actual situation the contrary, in the suction superheat unchanged, due to evaporation pressure has eased, the evaporator outlet pressure be reduced accordingly, pressure changes above and below the diaphragm, causing the main valve opening increases for increased fluid; but in a small pressure operating conditions, evaporation pressure rise, evaporator load demand for fluid volume increased, but the reality is that in the suction gas superheat unchanged, due to evaporation pressure rise, a corresponding increase in the evaporator outlet pressure, pressure difference above and below the diaphragm smaller, so that the main valve opening decreased for the reduction of liquid volume; in variable load is all about.

但在大压差工况下，蒸发压力降低，蒸发器负荷需求的液量减少，但实际情况相反，在吸气过热度不变的情况下，由于蒸发压力降低，蒸发器出口压力相应降低，膜片上下的压差变大，使主阀开度增大，供液量增加；但在小压差工况下，蒸发压力上升，蒸发器负荷需求的液量增多，但实际情况是在吸气过热度不变的情况下，由于蒸发压力上升，蒸发器出口压力相应提高，膜片上下的压差变小，使主阀开度减小，供液量减少；在变负荷下亦如此。

In the United States, chronic alcoholism and hepatitis C are the most common ones.

在美国，慢性酒精中毒，肝炎是最常见的。

If you have any questions, you can contact me anytime.

如果有任何问题，你可以随时联系我。