查询词典 subcutaneous injection

Xinwei Yu injection is Yaxin Hong Kong International, one of the company name to the production and operation of vertical injection molding machine mainly run peeling machine, terminal machines, all kinds of wire tester surrounding equipment such as injection molding machine.

新威注塑郁公司是香港亚新达国际公司名下企业之一，以生产经营直立式注塑机为主，兼营脱皮机，端子机，各种电线测试机等注塑机周边设备。

This article analyzes systematically the work process of fuel injection system in detail. It analyzes the fault fundamentals and its influence of three coupling parts in the high pressure oil road and the injection process, three coupling parts include plunger coupling parts, delivery valve coupling parts and needle valve coupling parts. It discusses the pulse situation of fuel pressure under the every kind of typical fault model, and regarding this as according to pick up the pulse signal of pressure from the high pressure pipeline, and process wavelet decomposition, picks up the of parameter fault, make use of the model identification technique, realizes to the intelligent diagnosis of fuel injection system fault.

文中系统地分析了燃油系统的工作过程，对高压油路中三偶件(柱塞偶件、出油阀偶件、针阀偶件)、喷油过程等的故障机理及其影响进行了分析，讨论了各种典型故障状态下的燃油压力波动情况，并以此为根据，从高压油管处提取压力波动信号，提取故障参数，利用模式识别技术，实现了对燃油系统故障的智能化诊断。

Spiral mandrel injection, injection valve, or two connected with the screw hole injection into the fixture, make it the top tight valve stuffing box.

用注射螺旋顶杆、注射阀或两个接在一起拧入夹具注射孔上，令其顶紧阀门填料箱。

The results showed that the muscle weight of botulinum toxin injection side decreased. The craniofacial morphology of the botulinum toxin injection side were smaller in distances of zygomatic arch to mandibular lower border and ramus height than that of the normal saline injection side.

结果发现实验组大白鼠施打肉毒杆菌神经毒素侧其咬肌重量较施打生理食盐水侧及对照组小，其颅颜骨型态在颧骨弓至下颚骨缘距离，冠状突切迹最前端至下颚骨角状突最下点距离，均小於生理食盐水侧距离，有统计上之差异。

C, Injection Molding: injection molding stage is the injection screw in the fuel tank thrust, in the Reserve Room of the expected melt through nozzles, mold flow, the gate into the cavity.

三，注塑充模：注射充模阶段是螺杆在注射油缸推力作用，将储料室中的熔体经过喷嘴、模具流道、浇口注入型腔。

Singlefactor adjustment tests for the fuel injection parameter optimization were performed on a CA6DL235E3 heavyduty common rail diesel engine with the basic Euro3 injection maps by means of the INCA calibration tool, and the influences of the fuel injection parameters on the airfuel mixing and combustion were analyzed comprehensively with the help of the microscopic field histories found by the software STARCD.

在一台高压共轨CA6DL235E3重型柴油机欧3喷油MAP基础上借助INCA标定工具进行为优化喷油参数的单因素调整试验，并利用STARCD软件获取的微观场变化综合分析喷油参数对油气混合及燃烧的影响规律。

Objective: To observe local necrosis of rat livers resulted from glycolic acid injection and compare necrosis effects resulted from glycolic acid injection and ethanol injection.

目的：观察乙醇酸注射对大鼠肝脏的局部坏死作用，并与无水酒精注射所导致的鼠肝坏死程度作比较。

The application results of the N2 injection technology in Guantao reservoir of Du 84 block showed that the N2 injection technology during SAGD process was feasible and beneficial for expansion of steam chamber in sideways and increase of the horizontal sweep volume. N2 injection during SAGD process could effectively control the down flow of top water and lengthen SAGD production time by 3-4 years. Both the reservoir recovery factor and oil steam ratio could be improved.

研究结果表明，氮气辅助SAGD开采技术在杜84块馆陶油层开采中是可行的，有利于蒸汽腔的侧向扩展，增加蒸汽的横向波及体积；在SAGD过程中添加氮气能够有效控制顶水下泄，延长SAGD生产时间3～4年，提高了油藏采收率和油汽比。

The subcutaneous administration of sodium dimercaptosuccinate at a dose of 1500 mg/kg immediately after the intraperitoneal injection of trivalent antimonyl ammonium gluconate increased the LD_(50) of the latter from 90—112 mg/kg to 1300—1460 mg/kg.

皮下注射二巯基丁二酸钠1500毫克/千克，司将小鼠一次腹腔注射锑铵的半数致死量从90—112毫克/千克提高至1300—1460毫克/千克。静脉注身锑~(124)铵予家兔后，如立刻经同一途径注射二巯基丁二酸钠，亦可降低锑铵的急性毒性。

Rats in the sham operation group received braid at the coronary artery ligation site, no deligatin, and other procedures were similar, subcutaneous injection of saline (2 mL/d), for 7 days.

d，连续7 d。假手术组：在相应冠状动脉结扎部位穿线，不结扎，其余操作步骤相同，皮下注射生理盐水2 mL/d，连续7 d。

You can snipe the second and third union leaders from this position.

您可以鹬第二和第三工会领袖从这一立场出发。

Aiming at the currently shortage of XML streams quality detecting, this paper proposes a new forecasting method of XML streams quality by least squares support vector machines, which is used the method of XML keys' vector matrix as windows, and vector product wavelet transform to multilevel decompose and refactor the XML streams series, that can fulfill real-time checking demand of XML quality, and ensure constraint, consist- ency and integrality. For even more adapting net load, it proposes a control strategy by weight and adaptive adjustment to ensure XML streams quality.

针对当前XML数据流质量检测存在的不足，提出构建XML键的矢量矩阵作为窗口，利用矢量积小波变换多级分解与重构XML数据流，再结合最小二乘支持向量机对XML数据流质量进行预测的一种方法，满足XML数据流质量重构时实时检测的要求，保证XML数据的约束性、一致性与完整性；为了更好的适应网络负载，采取加权与自适应窗口调整等调度策略充分保证XML数据流的质量检测。