查询词典 styrene

The results show that the styrene is better than trans 2 butene as working gas, and the deposition rate is about 3～4 μm/h for styrene, 1 μm/h for the trans 2 butene.

使用反式 2 丁烯为工作气体的沉积速率相对较慢，最高为 1μm/h ，而使用苯乙烯时，沉积速率提高到 3～ 4μm/h。

When ATRP of styrene was investigated with 1-phenylethyl bromide/benzyl a,a-dibromide mixture as initiator, the GPC chromatogram shows two elution peaks and the molecular weighs of the peaks are approximately in a 2/1 ratio. It suggests that benzyl dibromide is a difunctional initiator of ATRP of styrene. The analysis of end group using 1H-NMR also proves the result above.

采用1-苯基溴乙烷／α，α-二溴化苄混合引发剂进行苯乙烯的ATRP反应时，所得聚苯乙烯的GPC谱图为双峰，分子量相差一倍，初步证明了α，α-二溴化苄引发苯乙烯ATRP反应时是双官能引发剂，并用~1H-NMR对聚合物结构进行分析，进一步证明了α，α-二溴化苄引发苯乙烯ATRP时是双端同时增长的。

Tatsu varieties is the production and operation of 12 major categories of more than 50 varieties, mainly for rubber-filled Products oil, aromatic oil, paraffin oil, naphthene oil series Products, Product, respectively, applied to natural rubber, styrene-butadiene rubber products, butadiene rubber, EPDM ethylene-propylene rubber and the oil-filled elastomer SBS and footwear industries in the TPR pellet production, and also applies to styrene-butadiene rubber, chloroprene rubber and processing of oil-filled, annual production capacity of 15,000 tons.

现生产经营品种达12大类50多个品种，主要产品为橡胶填充油、芳烃油、石蜡油、环烷油等系列产品，产品分别适用于天然橡胶制品、丁苯橡胶制品、，顺丁橡胶制品、三元乙丙橡胶乙丙橡胶及弹性体SBS的充油和制鞋工业中的TPR粒料生产，也适用于丁苯橡胶、氯丁橡胶充油及加工，年生产能力达15000吨。

The effects of varied impact modifiers including similar styrene elastomer, acrylnitrile-butadiene-styrene copolymerwith high content of polybutylene,ethylene- octene copolymer,butylene-styrene elastomer,styrene-butadiene-styrene elastomer,styrene/ethylene/butadiene/styrene block copolymeron the properties of su- per-toughened HIPS were investigated.

以高抗冲聚苯乙烯为基体树脂，采用双螺杆挤出机研究了不同抗冲击改性剂类苯乙烯弹性体、丙烯腈-丁二烯-苯乙烯共聚物高胶粉、聚烯烃弹性体、丁苯弹性体、苯乙烯-丁二烯-苯乙烯弹性体和苯乙烯-乙烯／丁二烯-苯乙烯共聚物对HIPS的增韧效果。

Being combining with products distribution in styrene oxidation, we propose the styrene epoxidation carry out with Ti metallacyclo intermediates, And at the same time Ti-ZSM-5 have properties both catalytic epoxidation and acid-catalysis, namely the skeletal Ti can catalyze styrene epoxidation to styrene oxide and the skeletal Ti and Al can provide Lewis acid site to cause the rearrangement of styrene oxide to phenylacetaldehyde rapidly, the solvolysis to glycols and the cleavage of C=C double bond. Ti-ZSM-5 can also provide Bronsted acid site simultaneously, which is also catalytic center for the solvolysis to glycols.

同时结合Ti-ZSM-5催化选择性氧化苯乙烯反应的产物分布结果，提出苯乙烯环氧化反应可能是通过金属有机环机理进行；Ti-ZSM-5同时具有催化环氧化和酸催化两种功能，其骨架钛可催化苯乙烯环氧化生成环氧苯乙烷，而骨架钛和骨架铝等可提供Lewis酸位使环氧苯乙烷迅速发生重排生成苯乙醛从而使其成为反应的主要产物，同时还可发生加成以及碳碳键的裂解等副反应：Ti-ZSM-5也提供Bronsted酸位，它也是生成加成产物的活性中心。

They will be easier to glue as I'll be gluing styrene to styrene with plastic weld.

他们将可以更轻松地胶，正如我将粘合苯乙烯苯乙烯塑料熔接。

In this system trimethylamine was used as a trigger. Under the highest yield of styrene oxide, the amount of oxidant, phase transfer and catalyst were respectively 31.16%、8.96%、1.15%relative to the amount of styrene. With the experimental data, the reaction dynamics of the system was studied.

通过对钼蓝-氧化三丁锡体系动力学的分析计算，得出在该反应体系中，苯乙烯催化氧化成氧化苯乙烯的宏观反应动力学方程为：，其反应级数约为n=2，反应速率常数h-1mol-1，反应活化能Ea=165.08kJ/mol。

Dibutyltin maleate,dioctyltin maleate,N-phenyl maleimide, N-(p-chlorophenyl) maleimide,N-(p-nitrophenyl) maleimide with unsaturated groups were synthesized using dibutyltin oxide,dioctyltin oxide,maleic anhydride, aniline,p-chloroaniline,p-nitroaniline as raw materials,respectively.Then dibutyltin male,ate/styrene bipolymer,dibutyltin maleate/styrene/methyl acrylate terpolymer,dibutyltin maleate/styrene/N-phenyl maleimide terpolymer ,dibutyltin maleate/styrene/N-(p-chlorophenyl) maleimide terpolymer ,dibutyltin maleate/styrene/N-(p-nitrophenyl) maleimide terpolymer ,dioctyltin maleate/styrene biopolymer,dioctyltin maleate/styrene/methyl acrylate terpolymer,dioctyltin maleate/styrene/ N-phenyl maleimide terpolymer,dioctyltin maleate/styrene/ N-(p-ehlorophenyl) maleimide terpolymer[P(DOTM/St/NC1PMI)],dioctyltin maleate/styrene/N-(p-nitrophenyl) maleimide terpolymerwere synthesized using DBTO,DOTO,PMI,N-p-ClPMI,N-p-NOPMI,styrene and methyl acrylate as monomers,respectively.

再以DBTO，DOTO，PMI，N-p-ClPMI，N-p-NOPMI，苯乙烯，丙烯酸甲酯等为单体，合成了马来酸二丁基锡/苯乙烯二元共聚物{P}，马来酸二丁基锡/苯乙烯/丙烯酸甲酯三元共聚物{P}，马来酸二丁基锡/苯乙烯/N-苯基马来酰亚胺三元共聚物{P(DBTM/St/NPMI)}，马来酸二丁基锡/苯乙烯/N-对氯苯基马来酰亚胺三元共聚物{P(DBTM/St/NClPMI)}，马来酸二丁基锡/苯乙烯/N-对硝基苯基马来酰亚胺三元共聚物{P(DBTM/St/NNOPMI)}，马来酸二辛基锡/苯乙烯二元共聚物{P}，马来酸二辛基锡/苯乙烯/丙烯酸甲酯三元共聚物{P}，马来酸二辛基锡/苯乙烯/N-苯基马来酰亚胺三元共聚物{P(DOTM/St/NPMI)}，马来酸二辛基锡/苯乙烯/N-对氯苯基马来酰亚胺三元共聚物{P(DOTM/St/NClPMI)}，马来酸二辛基锡/苯乙烯/N-对硝基苯基马来酰亚胺三元共聚物{P(DOTM/St/NNOPMI)}。

Underoptimal conditions, in toluene / dimethyl phthalate / TBP, after EAHQ was oxidizedwith 〓, then the catalyst and styrene were added, the conversion of styrene basedon EAHQ is 68%, the selectivity for styrene oxide based on styrene is 92% and theTON of the catalyst is 500; in toluene / phenyl ether / TBP, epoxidation of styrenewas performed with 〓 generated in situ, the conversion is 46%, the selectivity is94% and the product can be separated by distillation under reduced pressure.

优化条件下，甲苯／邻苯二甲酸二甲酯／TBP(2／2／1，体积比)中，EAHQ先用〓氧化完全后，再加入催化剂A和苯乙烯进行环氧化反应苯乙烯相对于EAHQ的转化率为68％，生成环氧苯乙烷的选择性为92％，催化剂A的TON达到500；甲苯／二苯醚／TBP(1／3／1，体积比)中，原位生成〓条件下苯乙烯相对于EAHQ的转化率为46％，生成环氧苯乙烷的选择性为94％，产物可通过减压蒸馏分离。

In the dissertation, a new stabilization method, equal-density method was adopted to prepare modified asphalts with storage stability at high temperature. In this method, a compound was prepared by premixing polymer and filler, and the compound was mixed with asphalt to prepare Polymer-Modified Asphalt by changing the ratio of polymer and filler. The asphalts with good storage stability were formed with the addition of filler, by regulating the density difference between polymer and asphalt. With identifying the effect of composition factor and the technique conditions on mechanical properties of polymer/filler compound and the molecular distribution of the polymer, identifying the effect of composition factor and the technique conditions on the properties and structure of polymer/filler modified asphalt, Styrene-Butadiene-Styrene copolymer, Low Density PolyEthylene, Styrene-Ethylene-Butadiene-Styrene block copolymer modified asphalts with good storage stability and performance were prepared. Rheological method, gel content analysis and swelling measurement were adopted to elucidate the interaction between the polymer and filler. Filler reduced the difference between the polymer and asphalt with the premixing technique, which led to the improvement of the storage stability of the modified asphalts. The thermo-oxidative aging process of base asphalt and PMA were studied and the effect of antioxidant additives on the base asphalt and PMA were analyzed.

本论文采用等密度方法，即预先混合聚合物与填料制备复合物，复合物在沥青中会吸收油份而溶胀，改变填料的用量从而调节聚合物与沥青的密度差异的方法，制备出高温贮存稳定的改性沥青，并研究了工艺条件和配方因素对聚合物/填料复合物力学和聚合物分子量分布的影响，系统考察了工艺条件和配方因素对聚合物/填料改性沥青性能与形态结构的影响，研制出性能优良、高温贮存稳定的苯乙烯-丁二烯-苯乙烯三嵌段共聚物、氢化SBS、低密度聚乙烯改性沥青，并通过流变学分析方法及凝胶和溶胀测试探讨了聚合物与填料的相互作用，指出经过预混工艺填料改变了聚合物与沥青的密度差异，以此说明聚合物/填料改性沥青高温贮存稳定的原因；研究了基质沥青和聚合物改性沥青热氧老化过程，并分析了抗氧剂对基质沥青及聚合物改性沥青的影响，探讨了抗氧剂提高沥青耐老化性能的原因。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。