查询词典 structure stability

Using the information from exploratory adit can class rock mass structure, drawing lessons from internal successful experiences in rock mass quality and weathering zone classification, dam abutment rock mass is classed by choosing quantization indices of rock mass structure, the outcome same as investigation, accord with commonly geoloical rule. Using the information from slope image can finish stability analysis of lithologic slope, get 3-D cutaway view and date, it is important datum for research engineering geoloical condition of dam abutment rock mass.

利用勘探平洞洞壁图片采集的结构面信息处理成坝肩岩体结构研究的基本量化指标及实体模型，进行拉西瓦水电站坝肩岩体结构类型划分，并借鉴国内岩体风化分带、岩体质量分级规范，以岩体结构量化指标作为风化分带和质量分级的主要指标，划分两岸坝肩岩体风化分带、岩体质量分级，划分结果与野外现场判定及地质师室内划分结果相符合；利用边坡图片解译结果完成了坝肩岩体抗滑稳定边界条件分析，及不稳定块体的量化值和三维展示图，为坝肩工程地质条件评价提供重要资料。

Ti-Si composite materials are mixed at atomic scale, and Ti-O-Si bond appears in all of the samples with different TiO2 content; the mixed oxides are mainly existed in the form of amorphous pattern, anatase appears when the TiO2 content is more than 80%, but compared with the intension of pure TiO2, it has not integrate structure. The acetic content has great influence in the specific area and crystal structure of the mixed oxides. 20TiSi has good heat stability, still possesses 11m2/g after calcined at 1100℃; calcinations on the large scale of temperature does not cause the break of Ti-O-Si bond, TiO2 is well dispersed in 20TiSi calcined at 1100℃, and it still existed in the form of amorphous.

结果表明：制得的Ti-Si复合氧化物具有很高的比表面积，在TiO_2含量为10％时达到681.5m~2／g，Ti原子进入Si-O四面体结构中，形成Si-O-Ti键，复合氧化物的稳定性好，当TiO_2含量低于60 wt％时，以无定型形式存在；当含量为80％时，出现锐钛矿型TiO_2，但与纯TiO_2相比晶型不完整：醋酸对Ti-Si复合氧化物的比表面积、晶型都有很大的影响；TiO_2含量为20％的20TiSi经1100℃高温焙烧后，仍有较高的比表面积(11m~2／g)，稳定性好，在较宽的温度范围内焙烧，没有引起Ti-O-Si键的断裂，分散度高，没有出现晶型TiO_2。

The Schur subspace iteration method is applied for the dynamic characteristic analysis of damped structure vibration system and coupled fluid－structure system. This method avoids complex computation and has good numerical stability. A accelerated technique and a pre－process method for the system matrix are suggested to improve the computational efficiency. The generalized uncoupled equation is obtained from the Schur matrix and a back substitution scheme of response computaton is developed.

第三部分将非对称特征值问题的Schur子空间迭代法应用于非经典阻尼结构振动系统和流固耦合系统的特征值分析，建立了相应的具体算法，并给出了用以提高迭代收敛速度的迭代加速和矩阵预处理等实用技术；利用Schur矩阵的结构特点，推导了系统方程的动力解耦形式，给出了响应计算的回代求解格式。

In addition, some modifications on several computational methods are also presented. Using LMTO method the electronic structure of several systems are studied, and some results are obtained. They are: The ideal Nb (100) surface has three surface states, the multi-layer relaxed surface has two surface states. The surface energy of the ideal surface is higher than that of the relaxed surface, that means that the multi-layer relaxed surface is more stable than the former one, which supports the LEED results. The mono-layer relaxed Ag (111) surface is the most stable one among several" stable surface models"presented by several researchers. The surface energy of Ag (111) surface is higher than that of surface Ag (001), which supports some experimental results such as different reaction rate at different surface orientations for the same material. The surafce states of Si (111) surface not only locate near the Fermi level, but also in the valence band, which agrees well with Cohen's conclusion. Si (111)-H is an effective model for analysing the surface states and H adsorbed on the back surface is a good method for improving the convincingness of the results obtained on thinner slab models. The surface stability depends on three different kinds of MoSi〓(001) surfaces, the surface with mono-layer Si is the most stable one, and the surface with Mo at the first layer is the most unstable one among them. These are consistant with the Kemoda's experimental results. The valence bands of clean or K adsorbed CdTe (111) surface agrees well with the synchrotron radiation studies. The surface of CdTe (111) consists of four kinds of surface models which show different surface electronic structures and different surface structure stabilities. The conclusion agrees well with Wu's experimental work. The different absorbed alkali metals on the CdTe (111) surface give different adsorption characteristics which have relations not only with the valence electrons, but also with the core ones of the alkali metals. The electonic structures of Si-C alloys are different from that of Si-Ge alloys, and the energy band gaps of Si-C alloys do not increase linearly with Carbon concentration, our conclusion supports Alexander's results, but conflicts with Soref's one.

现分述如下： LMTO方法及其应用方面：1）通过对Nb（100）表面电子态分析发现清洁理想表面有三个表面态，多层弛豫表面有两个表面态；表面能大小说明多层弛豫表面更稳定，支持了LEED结果。2）通过对采用不同方法获得的几种不同Ag（111）表面稳定结构的表面能计算分析，给出了单层弛豫表面为Ag（111）表面的最稳定结构；从Ag（111）单层弛豫表面和Ag（001）表面的表面能比较，发现了Ag（001）表面表面能要比Ag（111）小的，表明了同种物质不同表面取向将表现出不同物理、化学性质，这是与实验中得出的结论是吻合的，3）通过对Si（111）表面态分析，不仅发现了Si（111）表面不仅具有居于费米能级附近的悬挂键所对应的表面态，而且还有很多表面态位于价带能量范围内，与Cohen等结果一致，H饱和slab模型背表面相当于增加了slab层的厚度，是一有效的变相增加slab层厚的方法，弛豫表面较清洁理想表面价带谱们低能端的少许移动，预示着总能降低，说明弛豫表面较清洁理想表面稳定。4）MoSi〓具有三种表面，从费米能级上态密度值大小得到单层Si表面最稳定，Mo原子为表层原子的表面最不稳定，双层Si原子表面居中的结论，这与Kemoda等人实验结果是一致的。5）通过对CdTe（111）表面表面电子态、表面结构稳定性及表面H、碱金属吸附的电子结构系列研究，不仅得出了CdTe（111）清洁及碱金属K吸附价带谱与同步辐射光电子谱相吻合的结果，而且发现了CdTe（111）表面具有四类不同原子近邻特征，表现出四类不同的表面结构及电子结构特征：不同表面态分布、不同的表面结构稳定性（表层原子与次层原子成三键有一悬挂键的表面要比表层原子与次层原子成一键有三悬挂键稳定（与Wu等人实验结果一致））、不同的H吸附特性。

CQB-G uses multiple circulating cooling structure to ensure the dependability and stability of prime mover and magnetic drive. Meanwhile, pin coupling is used to reduce the noise and vibration of pump. The detachable type and pin coupling makes the structure of pump longer, which is good for heat dissipation.

CQB-G型磁力高温泵采用多重循环冷却结构，保证了原动力和磁传动的可靠性和稳定性，同时采用柱销联轴器减少了泵的噪音和震动，便拆式和柱销联轴器同时使用，使泵的结构增长，更有利于泵的散热。

All three attempts are found to be unsatisfactory; in particular, the absence of a rigorous understanding of social structure, and the concomitant failure to acknowledge and elucidate the embeddedness of the political dimension in that structure, have resulted in either normative explanations or declamatory remarks, neither of which could fully grasp the nature of political action or political stability and their attendant contingencies.

这些论述其实都并未能对问题作出令人满意的分析。在对社会结构缺乏深入了解，同时又未能掌握到政治活动基本上都是在特定社会环境之中进行此一特点的情况下，这些论述结果都流於成为规范指向的解释或演辩式的陈述，都未能充份掌握政治行动或政治稳定性的特质，以及这些问题的临时多变性格。

The selection of geological prospecting in different stages(initial-prospecting, detailed-prospecting)(2)the selection of geological prospecting in the deep-laid and shallow-laid of tunnel project (3)the selection of geological prospecting of tunnel projecting in different geological conditions Finally, the author summed up main problems needing to be solved in tunnel engineering geological prospecting as follow:(1)differentiate stratum and find out the depth and thickness of different stratums in the tunnel section (2)find out geological structure and existence situation of fault, broken zone and weak plane (3)find out weathering level of bed rock to classify surrounding rock combining speed materials (4)differentiate stratum structure of the entrance of tunnel to judge the stability of it (5)find out existence situation and performance of ground water (6)situations of other harmful geological phenomenon In view of above problems and classification of surrounding rock, the author showed principles of rational choosing of methods in geological prospecting and counted disperse range of physical character parameter value in different petrosal character, getting achievements as follow:(1)summarization of effect, merits and demerits of different geological prospecting methods in the tunnel geological investigation (2)method selection and arrangement principle of tunnel engineering geological prospecting in different geological conditions and prospecting stages (3)According to previous experience and cases, the author concluded the物性parameters most in use ,and showed the basis of selecting geological prospecting methods in different geological conditions.

论文中用几个应用实例来说明：(1)不同勘察阶段物探工作的选用；(2)深埋、浅埋隧道工程物探工作的选用；(3)不同地质条件隧道工程物探工作的选用。最后总结归纳出隧道工程物探所需要解决的问题主要有：(1)划分地层，查明隧道通过剖面的各地层深度与厚度。(2)查明地质构造，隧道轴线段有无断层、破碎带、软弱层面等。(3)查明基岩风化程度，从而结合速度资料进行围岩分级。(4)划分洞口地层结构，判断洞口稳定性。(5)查明地下水赋存情况及其活动动态。(6)其他不良地质现象存在情况。针对上述需要查明的地质问题与计算围岩分级情况，论文提出合理选用物探方法的原则，并统计了物性参数值在不同岩性中的分布范围。得出以下研究成果：(1)总结出各物探方法在隧道地质调查中的作用和优缺点。(2)得出不同地质条件下和不同勘察阶段，隧道工程物探方法选择和布置的原则。(3)根据以往工作经验和事例，对常用的物性参数进行了归纳总结，同时介绍了不同地质条件下物探方法选择的依据。

LsEQ is the ability of landscape eco-system to maintain self-stability of structure and function.So,assessment standard of LsEQ is defined to be the stability of landscape eco-system which lies on the contrast of interior stabilization degree and exterior ecological disturbance degree of landscape eco-system.

景观生态质量是景观生态系统维持自身结构与功能稳定性的能力，因此，景观生态质量的衡量标准是景观生态系统的稳定性，其稳定性取决于景观生态系统的自身稳定程度与外部生态学干扰程度的对比。

SF and collagen films were treated by negative corona discharge, homothermal surface potential decay was tested to detect the charge stability. Result showed circums- tance humidity influenced severely the surface charge stability. There were polar groups on the surface after corona discharge, and hydrogen bonds existed between these groups. On the other hand, ATR-FTIR analysis indicated the conformation transition of SF was induced by strong electric field and a part of random coil conformation was converted into β-sheet structure.

采用自制的负电晕极化装置对丝素、胶原膜进行了表面处理，等温表面电位衰减法测试材料在不同环境中表面电位的变化，发现环境湿度对材料表面电荷稳定性的影响较大；XPS光谱分析表明材料表面有极性基团产生，这些基团之间有可能会形成氢键，同时ATR-FTIR分析表明丝素的构象在强电场的作用下发生了变化，由无规线团转变为β折叠结构。

In the stability design of a high-power laser facility, if equiprobable allocation results are chosen as the stability design indexes, there are often much difficulty in structure design and great waste in building.

在大型固体激光器结构稳定性设计中，使用等概率分配方法的分配值作为光学元件稳定性设计指标常常会增加结构设计的难度，造成结构建造的巨大浪费。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。