查询词典 strength-increasing

The results show that the addition of cross-linker makes tensile strength of the material greatly increase. After the addition of dialdehyde starch, the tensile strength raises from 7. 2MPa to 13. 2 MPa. However, the strength of the material cross-linked by TDI greatly increases when the additive level is less than 10％ while the tensile strength of sample whose additive level is 20％ is even worse, which is mainly caused by the inner-flaw after cross-linking.

结果表明，交联剂的加入使材料的强度得到较大的改善，添加双醛淀粉后，材料的强度从原来的7.2MPa提高到13.2MPa，而添加TDI的材料在添加量10％以前强度有较大的提高，但20％添加量的样品的强度却很差，主要是由于形成的内部缺陷造成的。

Systematical researches were carried out on the cleavage strength of steel fiber concrete with 3 base strength grades,6 steel externalities and 4 fiber admixtures,and it is discovered that the cleavage strength of concrete increases as the base strength grade rises,and dumbbell-like,shield-like and hook-like steel fibers have good reinforcement effect while flat steel fiber has less reinforcement effect.

通过对3个基体强度等级、6种纤维外形、4种纤维掺量的钢纤维混凝土的劈拉性能进行系统研究，发现混凝土的劈拉强度均随基体强度等级增加而增大；哑铃、盾铃、端勾形钢纤维的增强效果较好，而平直形钢纤维的增强效果较小。

As for the factitiously specified allowable values,such as allowable deflection,allowable amount of wear,and so on,their magnitudes,which are confirmed on the basis of empirical formula,often have an interval value or a limit value,therefore they can be described suitably by minor type membership function, As for various strength values of parts,such as tensile strength,compression strength,contact strength and so on,their magnitudes,which are often confirmed only by approximate mean,can be described suitably with middle type membership function.

对于人为规定的各种许用值，如许用挠度值、许用磨损量等，根据经验公式确定它们的大小时往往有一个区间或一个极限值，宜用偏小型隶属函数描述，对于零件的各种强度值，如抗拉强度、抗压强度、接触强度等，实际中往往只能确定其近似的均值，宜用中间型隶属函数描述。

It was estimated pulp properties with Runkel ratio more than 1 would be harder in tension for fiber and less oriented fiber to make paper into fluffiness (Casey,1980), with flexibility coefficient less than 0.5, the paper had medium tensile strength, burst strength and folding endurance, with slenderness ratio no less than 75 that be the paper of medium tearing strength but suitable beating with per cent of wall fraction less than 40 per cent would be good paper (Rydholm, 1967) while fibers completely oriented to get higher tensile and burst strength.

牙髓腔的财产据估计超过1比率将难以在紧张、纤维少使纸纤维成蓬松型、弹性系数低于0.5，该报中等抗拉强度、爆裂强度和耐折、与细比不少于75文件中被撕裂，但适当强度击打元墙上分数占不到40%将好的文件(rydholm， 1967)而获得较高的完全纤维拉伸强度和爆裂。

This project in business mark to enter a bid the course of authorized strength in have adopted broad unite to reach software valuation have adopted GBQ2. 0 editions list valuation software, at the same time, according to reinforcing bar have carried out the professional software of reinforcing bar take quantity; In the technical course of authorized strength of marking part , the authorized strength for the plan of construction progress has adopted dream dragon software, have carried out the layout of network plan, and for being under construction , the plane on-the-spot is also drawn up with dream dragon plane design software , includes main part and foundation mainly in which plane with decorate the construction plane on-the-spot of 3 projects arrange picture; For entering a bid the authorized strength of letter part, us adopt specification enter a bid letter text, guarantee the regularness of entering a bid.

本工程在商务标投标编制过程中采用了广联达软件计价采用了GBQ2.0版本的清单计价软件，同时，针对钢筋进行了专业钢筋软件的取量；在技术标部分的编制过程中，对于施工进度计划的编制采用了梦龙软件进行了网络计划的编排，并对施工现场平面亦采用梦龙平面设计软件进行编制，其中平面图主要包括主体，基础和装饰三项工程的施工现场平面布置图；对于投标函部分的编制，我公司采用规范的投标函文本，保证投标的正规性。

The results show that the amorphous PLGA fiber with porous structure (0.1-1.0 μm) is obtained by diluted solvent spinning method and the mechanical properties is affected by pressure and temperature. Bending strength and shearing strength of the samples increase firstly and then decrease with the increase of molding temperature and pressure. While the molding temperature is 160℃and the pressure is 105MPa, the PLGA materials possess optimal mechanical properties, bending strength, shearing strength and bending modulus 187.3 MPa, 100.0 MPa and 2.5 GPa, respectively. The mild temperature molding PLGA materials are desired to play a grate role in non-bearing internal fixation devices.

研究结果表明：非晶多孔结构的PLGA纤维可通过溶液沉析纺丝的方法获得，其孔径为0.1~1.0μm；压制压力和压制温度对材料的力学性能影响较大，材料的抗弯强度、剪切强度和抗弯模量均随着温度和压力的增大而先增大后降低；在压制压力为105MPa，压制温度为160℃时，试样的力学性能比较理想，此时，其抗弯强度可达到187.3MPa，剪切强度达到100.1MPa，抗弯模量达到2.5GPa，可望作为非承重部位骨折愈合内固定材料。

The main reason why quarter-sawn board of Birch had smaller dry compressing shear strength than flat-sawn board of Birch in normal conditions was that Birch had different shear strength to the grain between quarter-sawn board and flat-sawn board. Meanwhile xylary rays in flat-sawn board were transversely cut and left a lot of pores in the flat-sawn board, so adhesive can enter these pores and turn into adhesive nail. While these pores provided a kind of tunnel for water, so cause this phenomenon that wet compressing shear strength of flat-sawn board of Birch was smaller than that of quarter-sawn board of Birch. The possible reason why quarter-sawn board of Oak had greater dry compressing shear strength than flat-sawn board of Oak in normal conditions was that ratio of springwood on quarter-sawn board and flat-sawn board was different.

造成柞木径切板的常态压缩剪切强度比弦切板的常态压缩剪切强度大的主要原因是，在径切板和弦切板上早材胶接的比例不同，径切板的胶合强度试件上早材胶接的比例相对少，而弦切板的胶合强度试件上早材胶接的比例比径切板的胶合强度试件上早材胶接的比例相对大，由于早晚材胶接过程中强度决定于早材，这部分胶接强度比较低，这就使得柞木径切板的常态压缩剪切强度比弦切板的大；同时在柞木弦径面胶接过程中由于实际胶接面积的不同也能造成弦径面上API胶粘剂与之形成的化学键的数量不同，这也是造成柞木径切板的常态压缩剪切强度比弦切板的大的原因之一。

Meanwhile,introduce the resource state of the huge Timber Mountain Gum × Flooded Gum timber of end too,combine gradually deficient wildwood timber resources in our country, so, huge Timber Mountain Gum × Flooded Gum timber physics mechanics nature includes the tail: Moisture content , density, swelling, obey the compression strength of the line, horizontal line compression strength , bending strength , resist curved elastic mould amount , resist intensity of cutting , carry on experimental study along line along line tensile strength and hardness, there is a very important and real meaning.

同时，也介绍了尾巨桉木材的资源状况，结合我国逐渐匮乏的天然林木材资源，因此，对尾巨桉木材物理力学性质包括：含水率、密度、湿胀性、顺纹抗压强度、横纹抗压强度、抗弯强度、抗弯弹性模量、顺纹抗剪强度、顺纹抗拉强度及硬度进行试验研究，将有着十分重要而实际的意义。

Experiments were conducted for testing root tensile strength and measuring root cellulose content of Medicago sativa and Digitaria sanguinalis. Results indicated that in the two species, both the tensile strength and percentage of cellulose were negatively correlated with root diameter, while a positive correlation was found between percentage of cellulose and tensile strength. The conclusion confirmed that the relationship among root tensile strength, root diameter and root cellulose content found in tree root system was held also in the two species.

对豆科的紫花苜蓿和禾本科的马唐根的抗拉力和纤维素含量的研究表明，根的抗拉强度和纤维素含量均与直径呈显著的负相关关系，根的抗拉强度与纤维素含量呈正相关关系，表明&木本植物根的抗拉强度、直径和纤维素含量关系&的研究结论在这两种草本植物上也同样适用。

In the design, we should note two things: It is a wine of surface material and the adhesive strength between the inner layer material is lower than the label adhesive strength; second label wine of the tear strength is higher than the surface material The tear strength, its purpose is to easy to damage when in open box Diaobao Cartoning.

在设计时，我们应注意两点：是一酒盒表层材料与内层材料之间的粘合强度要低于标签的粘合强度；二是标签的抗撕裂强度要高于酒盒表层材料的抗撕裂强度，其目的是为了易于在开盒时破坏掉包装盒。

The basic concept of FOP can be summarized as to further optimize effective prescription according to the standard of curative effects and with the aid of modern science and technology and theories of traditional Chinese medicine.

其基本内涵可概括为：以确有疗效的中药复方为研究对象，以现代科学技术和传统中医药理论为技术支持，以该复方所治病证的药效响应为评价标准，以优化重组疗效更优的新复方为研究目的。

Ever since our world has been a world, native forests have been indiscriminately exploited by man.

自从我们的世界一直是世界原生森林被任意剥削人。