查询词典 strain band

The applicability of this constitutive model is evaluated with the simulations of material tests conducted by Sasaki et al., includes (1)Uniaxially constant strain amplitude cyclic test,(2)Fast in tension/Slow in compression constant strain amplitude cyclic test,(3)Slow-fast-slow constant strain amplitude cyclic test,(4)Cyclic strain with tensile hold time test. Simulations based on this constitutive model have a good agreement with (1),(2) and (3), proofs that it can describe the cyclic stress-strain behavior of 60Sn/40Pb solder very well.

为验证本模式之能力，本文选择Sasaki等人之实验为对象，分别对60Sn/40Pb焊锡在(1)定应变振幅之循环单轴负荷实验、(2)拉伸快/压缩慢之定应变振幅循环负荷实验、(3)慢-快-慢之定应变振幅循环负荷实验、(4)拉伸应力保持之循环应变实验下的材料行为进行模拟，由(1)、(2)及(3)之结果证明本模式对60Sn/40Pb焊锡循环应力-应变整体行为具有理想的描述能力，并对循环塑性应变范围与应力范围之值有准确的预估。

The effects of strain rate on plastic formation and dynamic recrystallization of 7050 aluminum alloy were discussed. The results show that the deformation of the specimen is inhomogeneous, and the effective strain in the center of the specimen is maximum. The deformation inhomogeneity increases with the increase of strain rate. The effective stress of specimen is inhomogeneous. As the strain rate increases, the minimum stress value moves from the drum-shaped region to the heart of specimen. The standard deviation of dynamic recrystallization grain size decreases with the increase of strain rate.

模拟结果表明，热变形过程中，试样的各个部位的变形分布不均匀，心部的等效应变最大，变形的不均匀性随应变速率的增大而增大，但是变化的程度不大；试样内部各部位的应力大小分布不均匀，随应变速率的增大，最小应力值由自由变形的鼓形区域逐步向心部移动；动态再结晶晶粒尺寸标准偏差随应变速率的增加而减小。

A correlation of the experimentaldynamic response of the vessels with the theoretical finite element calculations ispresented and discussed.1 The response of the end caps is dominated by transverseand torsional deformation of the plates.The membrane strain is negligible compareto the lateral strain.2 In the lengthwise direction of the inner cylinder,themembrane strain has the same magnitude as that of the bending strain. But for theouter cylinder,the former is much smaller than the later at the same direction.3 Forboth the inner shell and the outer shell,hoop strains are primarily due to themembrane deformation.The amplitude of the circumferential flexural strain isconsiderably small.4 Peak strains in the vicinity of the connection portion of theend caps and the shells are very high.This is important to assess the safety of thecontainer in case of repeated use or tests.5 The applying load to the end cap isdifferent from that to the inner shell plate, but peak stains and nodal displacementsof these two structural parts are nearly the same.It can be inferred that the dynamicresponse of the end cap is greatly affected by the structural vibration excited by theimpulsive loading.

结果表明：1在本文所考虑的载荷水平下，平板变形以板的横向弯曲和扭曲为主，中面应变幅值比较小。2对于内容器，其纵向变形中弯曲应变和中面应变大小接近；而对于外容器，其纵向变形以弯曲为主，中面变形比较小。3内、外壳体的环向变形主要是中面应变，弯曲应变分量很小。4平板和壳体连接处应变很大，这对于多次使用或实验时评价结构安全有指导意义。5尽管内筒底板和大封头上的作用载荷有一定差别，但应变峰值和节点位移峰值基本相近，这说明脉冲载荷激发起来的结构振动对封头的动态响应有很大影响。

One pair of primers that amplified the gB gene of pseudorabies viruswas designed and synthesized.PCR technique detecting the DNA of PRV was established after selecting the best reaction conditions.This technique was applied to specifically amplify the 281 bp DNA fragment of the PRV strains including Fa,Fb,Bartha,BJ,GD,V2F4,S,S3,SR,Buk,Shope,Norden,Mink Ⅲ,HB,F8,F9 and F12 in cultured samples.The negative results were achieved from Vero cells,swine vesicular disease virus,hog cholera virus,Japanese encephalitis virus,porcine reproductive and respiratory syndrome virus,porcine parvovirus,foot and mouth disease virus F29 strain,O3I3 strain,T509 strain and O Ⅱ MF249 strain.The results of sequencing showed that the PCR method was of specificity.The sensitivity of PCR reached 15.8 pg of PRV Fa strain DNA.The tissue samples obtained during 1994 and 2000 were detected,and the results showed that the sensitivity of PCR was more sensitive than virus isolation and the Sandwich ELISA.The PCR was applied to detect 191 tissue samples from 31 pig farms obtained from Guangdong,Fujian,Hainan Provinces during 1999 and 2000,50 samples(26.2%)were positive and 22 pig farms(71%)were positive.

根据伪狂犬病病毒gB基因的序列，设计并合成了一对引物，以闽A株细胞培养毒为模板，筛选最佳反应条件，建立了检测PRV的PCR方法应用该方法对Fb、Bartha、BJ、GD、V2F4、S、S3、SR、Buk、Shope、Norden、MinkⅢ、HB、F8、F9、F12等毒株的细胞培养液进行基因扩增，均获得了分子量为 2 81bp的特异性目的DNA片段，而对Vero细胞与FMDV、SVDV、HCV、PRRSV、JEV、PPV等病毒进行检测，结果均为阴性，没有出现交叉反应对PRV毒株扩增的产物测序，结果序列与文献报道一致，证明PCR扩增产物和方法的特异性对 1994～ 2 0 0 0年期间送检的临床样品和保存的PRV毒种，用病毒分离、双抗体夹心ELISA和PCR等 3种方法进行检测，结果前 2种方法检测为阳性的，PCR检测均为阳性；PCR检测为阴性，前 2种方法检测也为阴性；可是，前 2种方法检测为阴性的，PCR却检测出部分阳性；经x2 检验，证明PCR检出率明显高于前 2种方法的检出率对PRV闽A株细胞毒提取物DNA进行检测，其最低检出量为 15 8pg 对 1999～ 2 0 0 0年期间广东、福建、海南等省的 31个大中型猪场送检的 191份病料进行检测。

The main research tasks and results are as follows:(1) Through comparing the stress intensity factor of compact tension specimen calculated by finite element software with the theoretical value, the feasibility of calculating fracture parameters of crack tip in ABAQUS software was verified.(2) The relationship between the elastic modulus of the material and research scale was studied based on deriving the cohesive stress theory and other relevant theories. And the elastic modulus of the material on meso-scale was determined.(3) Global model and sub-model of the finite element were built in th...e macro-scale, and stress-strain field nearby the crack tip was analyzed, and the results show that the detailed stress-strain in the crack tip could be obtained by using the sub-model technique.(4) In meso-scale, the crack growth model was also established by assuming the crack propagating along the grain boundary, and the detailed stress-strain field in the crack tip was obtained.(5) The effect of crack length on Von Mises stress, and maximum principal stress and strain was analyzed in meso-scale when equivalent KI equals 30MPa.m1/2. And the results show that except for crack tip area, the stress-strain distribution in whole specimen is not affected.

主要完成研究内容和取得成果如下：(1)利用有限元软件计算出紧凑拉伸试样的裂纹尖端应力强度因子KI值，其结果与理论值一致，从而验证了利用ABAQUS计算裂纹尖端相关断裂参量的可行性；(2)在研究内聚应力等相关理论的基础上，推导出了研究尺度与材料弹性模量的近似关系，并确定了介观尺度上的弹性模量；(3)在宏观尺度上建立了全局有限元计算模型和子模型，得到了裂纹尖端应力应变场分布，结果表明利用子模型技术获得比较准确的裂纹尖端应力应变场分布是可行的；(4)在介观尺度上利用平均晶粒尺度的方式建立了裂纹沿晶扩展模型，得到了裂纹尖端断裂过程区的微观应力应变场；(5)当应力强度因子为30MPa.m1/2时，分析了介观尺度上在裂纹沿晶扩展过程中裂纹长度对Mises应力、最大主应力和应变的影响，结果表明，裂纹扩展长度对试样整体应力应变分布影响不大，而对裂纹尖端区域有较大影响；(6)介。。。

It has been observed that a general strain fail criterion for clay is recommended for considering the integrative effects of torsional shear strain and normal deviatoric strain as well as cyclic strain and accumulative strain.

提出的综合应变式同时考虑了剪切变化和正向偏差变形的共同效应，适合作为主应力连续旋转的耦合循环剪切试验的破坏标准。

The dual-band differential LNA use Inductive source degeneration structure, a matching network is used for the LNA to develop dual-band. The micro-mixer use a matching network shunt and parallel LC elements to develop wide-band matching. The biasing method reduces the"voltage headroom" difficulties inherent to the Gilbert cell, and the mixer linearity can be improved using this biasing method "Charge -Injection"by accurate adjustment of the input MOSFET operating point. The complementary VCO based on 2.5GHz, and tuning output buffer to approach 2GHz/5GHz dual-band for dual-band down-converter with MMIC technology.

其中双频差动低杂讯放大器，本电路用Inductive Source Degeneration 架构，在匹配网上设计，使低杂讯放大器工作在个频带上达成双频带的效果；CMOS 微混频器上采用LC串联、并联电路做匹配，达到宽频匹配的效果，并加入了"Charge-Injection"的方法来改善"voltage headroom"的问题，并同时提高线性度的表现；互补式压控振荡器以2.5GHz为基频的振荡器为出发点，透过电路的调整，以期达成2.5/5GHz的双频带需求，能够完整达成双频带接收机系统。

Forbidden-band-width of mono-clinic phase of bismuth vanadate (mBiVO4) is high enough to 2.3-2.4 eV, it could be valence band to carry out entirely that hole band degrade organic pollutants,and the conduction band possesses high oxidizability to make for reduction of photoinduced electron,and oxidation potential of its valence band with 2.4 eV nearby could achieve decomposition of water and degradation of organic pollutants under visible light.

单斜晶相钒酸铋(mBiVO4)的禁带宽度为2.3 - 2.4 eV，它足够高的价带完全可以实现空穴对有机污染物的降解，并且导带位置也有利于光生电子的还原，具有较高的氧化能力，且其价带氧化电位位于2.4 eV附近，可实现在可见光下分解水和降解有机污染物。本文综述了mBiVO4应用于降解污染物、光解水产氧以及光电化学分解水的研究概况，及其在光催化降解有机物等领域的应用前景。

The EDT parameter has been studied both in octave band and in 1/3 octave band, and, by using some tools developed for this work in Matlab environment, it has been possible to verify the correlation between the normal modes of the orchestra pit and the highest temporal values traceable to the central band frequencies, the relatives both to the octave band and the 1/3 octave band of the parameter examined.

文中对EDT从倍频程以及1/3倍频程加以研究，并利用在Matlab环境下开发的一些工具来探讨乐池的简正模式与从频带中心频率导出的最大的时间值之间的相关关系。

Five main phenomena were found, firstly, the high plasticity clay could well suitable to large deformation, and had strain-hardening behavior obviously, as well as, the little dilatancy; secondly, there was no correlation between stress paths and shear strength but the stress-strain relations were influenced by stress paths; thirdly, the little stress increment ratio, the higher increase speeding of shear stress and breaking strength under the condition of same initial normal stress; the fourth, the relations between normal strain and normal stress in simple shear test was consistent with which in the single-direction compression test, if there was no dilatancy; the last, the curve of relation between stress ratio and shear strain could be well simulated by hyperbola.

试验结果表明，高塑性粘土能够较好地适应大变形，接触面剪应力与切向应变关系呈剪切硬化型曲线，法向剪胀不明显；接触面剪切强度与应力路径无关，应力应变关系与应力路径密切相关；初始法向应力一定，应力增量比越小，剪应力增长越快，对应的破坏剪应力也越高；无剪胀发生情况下，法向应变与法向应力关系曲线与单向压缩试验具有一致性；应力比与切向应变呈良好的双曲线关系。

Looking to bounce back from defeat against Cesena last weekend, the Calabrian boss will be sticking to his tried and tested 4-3-3, with Lopez and Sedivic joined up front in Giampaolo's absence by either Nanni or Plasmati.

鉴于上周末对切塞纳的比赛中反败为胜，这支南方球队将会更坚持其一贯而有效的4-3-3阵型，洛佩斯和塞德维奇将取代受伤缺席的詹保罗，和纳尼或者帕斯马蒂中的一个搭档锋线。

Meanwhile, their exposure to the more freewheeling ways of the West broadened dramatically.

另外，西方较自由的生活方式对年轻人的影响增大。