查询词典 stepper
- 与 stepper 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
This paper presents a stepper motor drive control system design, including its clock pulse circuit, pulse distributor, and the drive circuit and power supply design.
摘 要:本文介绍了一种步进电机驱动控制系统设计方案,包括其时钟脉冲电路、脉冲分配器、以及驱动电路和供电电源的设计。
-
The main objective of this design is the completion of the stepper motor control.
本设计的主要目标是完成步进电机的控制。
-
This system uses a MCU as a core , a keyboard and infrared detecter as the input system ,a LED display circuit, a warning circuit and a stepper motor as the output system to realize the auto controlling of the liquid drop speed .
本次设计的系统,是以8031单片机为核心以键盘及红外传感器为输入系统,以数码管、报警电路及步进电机为输出系统的智能化的液体点滴速度的控制及监测系统。
-
The doctor blade gap is set with an accuracy of 0.02 mm by two precision ball-screw stepper-motors,one on each side of the doctor blade.
刀片间的距离的精确度达0.02毫米,这是由位于刀片两端的两个精制球状螺钮步进电机来确定的。
-
But the stepper motor'sefficiency is low;much of the input energy must be dissipated as heat.
但是步进电机的效率低;多数的输入能量都必须以热量耗散掉。
-
In this paper, the frequency response of the stepper motor as an electro-mechanical transformer is investigated.
针对步进电机固有的特点,对其作为电-机械转换元件的频率特性进行了深入的研究。
-
The design of the device using NC Lathe CA6240 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with.
本设计利用数控装置对CA6240普通车床进行控制,主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴,通过变频器和齿轮变速箱实现分段无级变速;进给系统采用步进电机通过减速后驱动滚珠丝杠运动,在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠,在横向进给系统中通过二级齿轮减速驱动滚珠丝杠;刀架改为自动转位刀架从而实现自动换刀;通过MCS-51系列8051单片机对数据进行计算处理,由I/O接口输出步进脉冲信号控制进给速度和行程;为了保持切削螺纹的功能,要在主轴外端或其它适当部位装上脉冲发生器;将车床的手动尾座改造成为可控电动尾座。
-
This paper analyses the influence rule on tooth-layer permeance constant component and harmonic component with tooth-layer parameter and magnetometive, It offers basis to calculates the performance of the linear stepper motor with analytical method and optimized design for linear stepping motor.
最后,运用齿层比磁导函数化方法对直线步进电动机的最大电磁推力特性进行了定量研究,分析了永磁体参数、齿层参数对混合式直线步进电动机永磁体工作点的影响,分别计算了不同永磁体参数和齿层参数时的最大电磁推力特性。
-
It refers to stepper motor, hydraulic slide valve, position feedback loop combination in the design of internal hydraulic cylinder, connected to hydraulic oil source, all the functions directly through a dedicated digital controller, computer or PLC programmable logic controller A digital pulse signal to complete the length of vector control of high-tech products.
它是指将步进电机、液压滑阀、闭环位置反馈设计组合在液压缸内部,接通液压油源,所有的功能直接通过专用数字控制器、计算机或PLC可编程控制器发出的数字脉冲信号来完成长度矢量可控的高新技术产品。
-
In this paper, a stepper motor controller design, and drew a schematic and PCB board map, write the program source code.
本文阐述了一种步进电机控制器的设计方案,并绘制了原理图和PCB板图,撰写了程序源代码。
- 推荐网络例句
-
On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.
另一方面,更重要的是由于城市住房是一种异质性产品。
-
Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.
气候直方图是将所收集的降水量测定值,分为几个相等的区间作为横轴,并将各区间内所测定值依所出现的次数累积而成的面积,用柱子排起来的图形,也叫做柱状图。
-
You rap, you know we are not so good at rapping, huh?
你唱吧,你也知道我们并不那么擅长说唱,对吧?