查询词典 step back

In plastic step sucking back is very important too. Sucking back include front sucking back and back sucking back It setting sucking back to prevent flow and line. It sets sucking back speed and pressure within 20-50% and distance within 2-5cm. TOO long distance make cyclinder reserve air and cause bubbleat next molding.

熔胶过程还有一个比较重要的环节，那就是松退，松退分前松退和后松退，其作用一般是为了防止流涎和抽丝，设定值速度和压力都在20%-50%间，设定的行程一般在2-5cm间，太长的行程可能会使料筒里面贮存空气，导致下一模出现不期望的气泡。

In plastic step sucking back is very important too. Sucking back include front sucking back and back sucking back It setting sucking back to prevent flow and line. It sets sucking back speed and pressure within 20-50% and distance within 2-5cm. TOO long distance make cyclinder reserve air and causebubble at next molding.

熔胶过程还有一个比较重要的环节，那就是松退，松退分前松退和后松退，其作用一般是为了防止流涎和抽丝，设定值速度和压力都在20%-50%间，设定的行程一般在2-5cm间，太长的行程可能会使料筒里面贮存空气，导致下一模出现不期望的气泡。

In plastic step sucking back is very important too. Sucking back include front sucking back and back sucking back It setting sucking back to prevent flow and line. It sets sucking back speed and pressure within 20-50% and distance within 2-5cm. TOO long distance make cyclinder reserve air and cause bubble at next molding.

熔胶过程还有一个比较重要的环节，那就是松退，松退分前松退和后松退，其作用一般是为了防止流涎和抽丝，设定值速度和压力都在20%-50%间，设定的行程一般在2-5cm间，太长的行程可能会使料筒里面贮存空气，导致下一模出现不期望的气泡。

In plastic step sucking back is very important too. Sucking back include front sucking backand back sucking back It setting sucking back to prevent flow and line.It sets sucking back speed and pressure within 20-50% and distance within 2-5cm. TOO long distance make cyclinder reserve air and cause bubble at next molding.

熔胶过程还有一个比较重要的环节，那就是松退，松退分前松退和后松退，其作用一般是为了防止流涎和抽丝，设定值速度和压力都在20%-50%间，设定的行程一般在2-5cm间，太长的行程可能会使料筒里面贮存空气，导致下一模出现不期望的气泡。

In plastic step sucking back is ery important too. Sucking back include front sucking back and back sucking back It setting sucking back to preent flow and line. It sets sucking back speed and pressure within 20-50% and distance within 2-5cm. TOO long distance make cyclinder resere air and cause bubble at next molding.

熔胶过程还有一个比较重要的环节，那就是松退，松退分前松退和后松退，其作用一般是为了防止流涎和抽丝，设定值速度和压力都在20%-50%间，设定的行程一般在2-5cm间，太长的行程可能会使料筒里面贮存空气，导致下一模出现不期望的气泡。

Plastic should lower 3 steps, because plastic is a step to add melt resin material to cyclinder , Higher stick of resin material ,higher screw back pressure. Screw speed differs depending on decomposing temperature of resin material ,Higher screw speed ,Higher trim force of resin, higher cyclinder temperature.Some resin material may decomposes so it set screw speed in mid-speed such as 45-75%, In plastic step setting screw back pressure is very important, Higher screw back pressure ,higher quality of product screw back pressure make resin structure order, Molding product is beautiful and volume stable. But

再复杂的熔胶旋转过程最多不会超过三段，因为熔胶本身就是存在于把胶熔进料筒的过程，如果原料粘度大，熔胶压力则大，但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大，故一般熔胶会采用中速为宜，如45%-75%，熔胶同时会碰到一个比较重要的环节，那就是背压的使用，产品精度要求越大，背压的使用则更大，背压可使原料分子间结构更紧密，成型出的产品则尺寸更稳定，外观越好。

Front handspring, step out, round off, back handspring, step out, round off, back handspring, full twisting lay out.

前手翻，向前一步，侧翻内转，后手翻，向前一步，侧翻内转，后手翻，360度转体落地。

Whiteney: Front handspring, step out, round off, back handspring, step out, round off, back handspring, full twisting lay out.

Whiteney ：前手翻，向前一步，侧翻内转，后手翻，向前一步，侧翻内转，后手翻，360度转体落地。

Without method, oneself tried to change a map to make a tool, who knew to change had done not have weight of page of a day of content to fall completely, before snapshot of film of a lot of serialize turned N into the day, the map shows like that wait for calm, the content in the map is different nevertheless, the map that makes previously has time and address only, did not update frequency and first step, what use from the back is online generate a tool to have first step and newer frequency, because the map from the back has first step,knowing is inside the first grade with acquiescent page is reduced bring about fall authority or what are other reason, stationmaster is here people the place that ace gathers, experienced and knowledgeable, my map now is to show all the time treat calm condition, the station is Http://www.dy3166.cn, home page weight did not change, namely inside page weight was done not have, hope ace people help seek next accounts, declare, oneself are acclaimed by no means in this hair post, was to come up against this a Gordian knot really, hope ace people can help solve below, thanked.

没有办法，自己试着换了个地图生成工具，谁知道换了没过一天内容页权重全降了，好多连载影片快照都变成了N天前的，地图那一样显示待定，不过地图里的内容不一样，以前生成的地图只有时间和地址，没有更新频率和优先级，后面用的在线生成工具有优先级和更新频率，不知道是不是因为后面的地图有优先级把内页默认的优先级别降低导致的降权还是什么其他原因，这里是站长们高手云集的地方，见多识广，我的地图现在一直都是显示待定状态，站是http：//www.dy3166.cn，首页权重没有变，就是内页权重没有了，希望高手们帮忙找下原因，申明，本人在此发帖绝非炒作，是确确实实碰到了这个棘手的问题，希望高手们能够帮忙解答下，谢谢了。

At the clock point to 1:20 minutes for,"E11" step on plane door's counter first , it give service to the figure appear Le,I at the moment take out our step on plane board stand up on front, thank let she check up and affirm for, she received out step on plane board after, at the moment at the it above writing same words after and pass on go back for I, I'm one look meane feeling big thing don't be good: she already take our step on plane broad on the "E11" step on plane door use red pencil for draw out,at it's side write on "C8A"three words.at once, I'm all body the spirit be encourage call into actior up: I'm at once for first response's consciousness to,we're wall unable to catch up with this one's regular plane Le.

当时钟指向1：20分时，&E11&登机口柜台前，其服务员的身影出现了，我立即拿出我们的登机牌起身上前，想让其检查并确认一下。她接过我们的登机牌后，立即在其上面写了几个字后又递还了给我，我一看就觉得大事不好：她已把我们登机牌上的&E11&登机口用红笔划掉，在其旁边写上&C8A&三个字。顿时，我全身的神经被激淩发动了起来：我当时的第一个反应是意识到，我们将赶不上这趟班机了。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。