查询词典 steel structure

Which is with flexible spring steel supporting components and the air for damping medium to overcome these shortcomings which are complicated air spring structure and high prices, the need for daily use and maintenance costs of steel spring isolator without damping.

它以钢弹簧作弹性支承元件、以空气作阻尼介质，克服了空气弹簧构造复杂、价格高、需要日常使用维护费用和钢弹簧隔振器无阻尼的缺点。

A theoretical model is built to investigate the simulation of the infrared characteristic of the metal structure with the PCM false target.Structure parameters of the PCM false target that suit for the simulation are investigated numerically.According to the results,further request on the improvement of the thermal conductivity of PCM is presented.An experimental platform is built and the numerical model is validated experimentally.Three key thermal characteristic components of the false tank(barbette,wheel and front armor plate) are manufactured and tested,and good results are obtained.A method for the thermal conductivity enhancing of PCM by using aluminum fins is studied,the influence of the structure parameters of PCM plates to the simulation effects are investigated numerically,and the reasonable configuration parameters of the PCM plates used to simulate the steel plates of different thickness are obtained.In the study of the application of heat convection method in IR false target,a passive infrared simulation system is designed to simulate the infrared characteristic of metal constructions.The system is made up of pipe-plate,pump,receiver,and working fluid.

在相变材料应用于红外示假的研究中，通过数值模拟，研究确定了适用于制作假目标的相变材料各物性参数的范围，分析了相变材料制作假目标的可行性，并根据所得结果，选取石蜡为研究对象，建立了相变材料模拟金属构件红外特征的理论模型，研究了适用于模拟各金属构件红外特征的相变材料假目标的相关结构参数，得出了相变材料假目标模拟各金属构件红外特征的理论结果，并对相变材料的导热系数这一物性提出了进一步的改进要求；搭建了假目标实验平台，验证了所建理论模型的准确性；以坦克假目标为研究对象，制作了炮塔、负重轮和前上装甲板三个坦克假目标的关键红外热特征部件，并进行了野外实验，取得了较好的结果；以添加铝肋片作为改进相变材料导热能力的手段，理论研究了此类导热增强型相变材料的相关结构参数对模拟效果的影响，得出了模拟不同厚度钢板红外特征的导热增强型相变材料的结构参数及模拟效果。

This paper made displacement calculation and analysis adopting beam3, beaml88 units through ansys software, then compared the displacements of upper steel frame of mixed-layer structure and single story workshop under different loads and established the reasonable domain of displacement coefficient about mixed-layer structure, thus provided references and basis for the design of such structure.

针对一种新型结构即混凝土与钢结构混合而成的结构一混层结构，通过ansys软件，采用beam3、beam188单元对此新型结构进行位移计算及分析，并通过在不同荷载工况下混层结构的上层钢架位移与单层厂房的钢架位移进行比较分析，确定混层结构位移影响系数的合理范围，为此类结构的设计提供参考依据。

On the basis of the improved structure and under the premise of meeting specification requirement, the light steel door-truss structure is optimally designed by changing, cycle checking and gradually reducing the cross section size of overall structural member with the ANSYS parametric design language. The mechanical properties such as changes in stiffness, strength and stability of the optimized structure are completely analyzed under three load cases.

基于改进结构，在满足相关规范的前提下，利用ANSYS软件的参数化命令流语言（ANSYS parametric design language， APDL），通过改变结构杆件截面尺寸，对整体结构杆件的截面采用循环校核、递减尺寸，并对轻钢门式桁架结构进行优化设计，分析了优化结构在3种荷载工况组合条件下的整体刚度、强度及稳定性等力学性能的变化，给出了改进前后与优化前后结构的力学特性对比。

The developed program also has some post-processing functions including structure shape map, discrete structure mesh map, structure displacement map, cracking map, stress map of steel bar, principal stress map of any section, searching displacement of any load step, load-deflection curve map of any node and so on.

包括结构形式图、结构剖分网格图、结构变形图、裂缝开展图、钢筋应力图、任意横截面的主应力图、加载过程中的任意荷载下的位移查询、任意结点的荷载—挠度曲线图等。

To resolve the design difficulties caused by small cross-section, low height of the bridge structure, the key technique problem to the bridge structure should be carried on research and analysis, such as whole calculation model, considering foundation combined action , the reasonable rigidity match to the joint of the girder and pier ,inner force redistribution caused by the system conversion ,the forecast to long-term deformation after building , stress analysis and tectonic steel bar of the anchored serration block , the influence of foundation settlement and anti- earthquake measures . To acquire feasible and reasonable technique parameters and provide the full design basis, according to analytical results adjust and optimize the bridge structure design.

为解决桥梁结构要求截面小，高度低等带来的设计困难，需对该结构的关键技术问题如考虑基础共同作用的整体计算模型、梁墩间的合理刚度匹配、体系转换产生的内力重分布、成桥后的长期变形预测、锚下锯齿块应力分析及配筋构造、基础沉降影响及抗震措施等进行研究分析，以获得技术可行、经济合理的技术参数，为设计提供充分的依据，根据分析结果调整优化桥梁结构设计。

The test result shows that the mechanical properties of the dual-phase structure are much higher than those of ferritic plus pearlitic structures, that the dual-phase structure is of better corrosion resistance in some cases for Ca_2 has corrosion-moderating effects, and that hot-rolling dual-phase structure of the low-carbon Mn-Si steel wit...

试验结果表明：双相组织的力学性能远高于通常的铁索体+珠光体组织；在一定条件下，双相组织具有更好的耐蚀性，Ca_2有明显的缓蚀作用；采用台阶淬火工艺，不含Cr、Mo的低碳锰硅钢也易于获得热轧双相组织。

The Stacker-reclaimer system has the tanglesome steel frame structure, therefore the guarantee the anti- pulled and anti- pressed intensity of the structure and the equipment distortion is precondition to improve on the structure of the equipment .

堆取料机系统具有结构复杂、旋转半径大的大型钢架结构设备，因此保证结构的抗拉压强度和设备整体绕度是改进设备的结构性能的前提。

A water model for simulation of 1050 mm mold is established to investigate the effects of SEN structure, casting speed, immersion depth and other parameters on the fluctuation of the liquid level in the mold, the impact depth of the steel stream and entrapping of the flux, and compare the influence of different structure parameters and operating parameters on the flowing field in the mold in order to find out the best suitable compromise between the structure parameters and the operating parameters and then...

针对 10 5 0mm× 15 0mm断面的结晶器，建立了水模型，研究浸入式水口结构、拉速、浸入深度等工艺操作参数对结晶器液面波动、流股冲击深度及结晶器钢液面保护渣卷入情况的影响，比较不同水口结构参数及操做参数对结晶器内流场的影响，从而找出结构参数与工艺参数间配合最佳的工况，为水口设计提供理论依据，并经优化的水口在实际中应用，使安钢第二炼钢厂的板坯退废率由 1.5 0 %降为0 。6 %。

Jingjiang City, double-hung steel valve factory founded in 2001, the current owner has developed into more than 60 employees and occupies an area of 5000 square meters, fixed assets of 8,000,000 yuan professional manufacture metallurgical, mining, electricity, chemical industry machinery and equipment, such as the backbone of enterprises, setting up a research institute, special casting, cast steel, cast iron, metal structure, machining, heat treatment, assembly, such as eight workshops, has a steel cutting machine, special casting equipment, Large floor boring machine, gantry milling machine, heavy duty horizontal lathe and CNC lathe machining and other large and medium-sized equipment and heat treatment equipment.

靖江市双鸿特钢泵阀厂创建于2001年，目前已发展成为拥有60余名员工、占地5000平方米、固定资产800万元的专业制造冶金、矿山、电力、化工等机械设备的骨干企业，下设一个研究所、特种铸造、铸钢、铸铁、金属结构、机械加工、热处理、装配等八个车间，拥有钢材切割机、特种铸造设备、大型落地镗床、龙门铣床、重型卧式车床及数控车床等各种机械加工设备和大中型热处理设备。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。