查询词典 spur gear

It is consisted of master pincer and back pincer,its nose opening is big.It is powered by a hydraulic motor with low speed and high torque,and driven by spur gear,4-fift gearing ,overhand mounting and pneumatic advancing and returningl.

由主钳和背钳组成，钳头开口大，低速大扭矩油马达输入动力、直齿圆柱齿轮传动，四档变速，悬吊安装，气动进退。

The final drives are double reduction with spur gear and segment sprocket, which are sealed by duo-cone seal

两级直齿轮减速，浮动油封密封，链轮采用组合式，便于维修。

Overseas low-pressure gear pump gear often used square structure,水力控制阀, that is the tooth width is equal to addendum circle diameter.

国外低压齿轮泵的齿轮常采用方形结构，即齿轮的齿宽等于齿顶圆直径。

The company produces the processing equipment to be advanced, check-out facility excellent, has the numerical control lathe, the numerical control drilling machine, the machining center, the numerical control gear-hobbing machine, the gear shaper, the fine borer, the universal milling machines, each kind of grinder, the table planer, the booklet bender, the large-scale lathe, the mechanical slicer, high intermediate frequency quenching, the well type, the box-type hardening furnace, the tempering furnace, the automatic welding machine, the X-ray crack detection machine, the cloth, the Rockwell tester; Electric hoist test platform, sound-level meter, varnish film thickness gauge, altazimuth, level; The material analysis laboratory, the metallography analysis room and so on full had guaranteed strictly the vehicle, the mill, dig, rub, pull, the boring, to drill, the ramming, cutting, the angle iron, the chemical examination and the heat treatment and so on complete technical process.

公司生产加工设备先进，检测设备精良，拥有数控车床、数控钻床、加工中心、数控滚齿机、插齿机、精密镗床、万能铣床、各种磨床、龙门刨床、折弯机、大型车床、刨床、高中频淬火、井式、箱式淬火炉、回火炉、自动焊机、 X射线探伤机、布、洛氏硬度计；电动葫芦试验台、声级计、漆膜测厚仪、经纬仪、水准仪；材料分析化验室，金相分析室等充分严格保证了车、铣、刨、磨、拉、镗、钻、冲压、切割、弯板、化验及热处理等全部工艺流程。

It comprises an in-put shaft hinged to its yoke through one axis, and an out-put shaft also hinged to its yoke through another axis, and these two yokes (13) were combined together by only one axis position, perpendicular to that two yoke axes like a cross, so that this combined axis will bend just like the angle bisector of that two shafts to maintain its constant velocity by a few methods, firstly, by using a section of gear teeth mesh at both ends of the shafts' teeth were so polished so that it can turn longitudinally as usual gear, and also sideways, to provide a larger solid angle of turning from ordinary 45 degrees into 60 or even more.

它包括输入轴，其通过一根轴铰链连接于叉形支架，和输出轴，其通过另一根轴也铰链连接于其叉形支架。并且这两个叉形支架(13)只需用一根相对垂直铰链轴相连而组合在一起，使得这种组合的轴总能形成这两个轴的角平分线，以通过少数几种方法保持其恒速，首先，通过用啮合在轴的两端的一段齿轮齿抛光为以能够像普通齿轮一样纵向转动，并且还能够侧向转动，以提供较大的转向立体角，从通常的45度变成60度或更大。

Aiming at the signal processing problems that exist in online fault diagnosis for train running gear, based on discussing the principle of characteristic spectrum analysis, a method of full period and uniform angle sampling is applied, which transfers the vibration signal from time domain into angular domain. The angular domain signal is transferred into corresponding characteristic spectrum using FFT. Through spectrum estimation and analysis, fault characteristic spectrum values of running gear components are acquired to distinguish their faults.

在讨论特征分析方法原理的基础上，针对机车走行部故障在线监测过程中存在的信号分析与处理问题，运用整周期等角度采样方法将时域振动信号转换为角域信号，采用FFT变换将角域信号变换为对应的特征频谱，通过谱估计、谱图分析得到机车走行部各零部件的故障特征谱值，再根据该特征谱值识别机车走行部各零部件的故障。

The micro vehicle rear axle of car main gear box noise question became the worker matter of concern. In this paper, the micro vehicle rear axle of car main gear box noise performance present situation and the traditional assessment method are discussed, and the general BP neural network and the Levenberg-Marguardt algorithm are introduced in detail. Improves the BP neural network using the LM algorithm, at present is trains the neural network the quickest algorithm.

微车后桥主减速器噪声问题成为工作者所关注的问题，本文介绍了后桥主减速器噪声性能现状及传统评价方法，阐述了BP神经网络的一般算法，并详细介绍了Levenberg-Marguardt算法，利用LM算法来改进BP神经网络，目前是训练神经网络的最快算法。

First the clutch is depressed, then the shifter is thrown into the next gear, and finally the clutch is released putting the car back into gear.

首先是离合器被踩下，然后把变速杆移到下一个档位，最后离合器抬起使车开始以新的档位运行。

Conquest series is the high-end Japanese version of Calcutta TE reels, and assumes the highest line of Shimano round bait casting reels. In the off-set gear box are advanced oversized gear systems, providing the smoothest ever retrieving.

西马诺Calcutta Conquest系列，是日版Calcutta TE的顶级增容版，被厂家定调为西马诺鼓式卷线器中的极品，内置精密的配件和装置，确保该系列产品的高效工作表现。

In the fourth chapter, all the calculating equations of fault vibration frequency of gear shafting components of gear unit are summarized and the calculating equations of fault vibration fiequency of commonly used barrel-shaped roller bearing are deducted.

另外，为了防止齿轮减速机在工作时发生突发性事故和更好地延长齿轮轴系部件的寿命，需对具体的齿轮减速机设备进行在线监测和智能故障诊断方面的研究。

You can snipe the second and third union leaders from this position.

您可以鹬第二和第三工会领袖从这一立场出发。

Aiming at the currently shortage of XML streams quality detecting, this paper proposes a new forecasting method of XML streams quality by least squares support vector machines, which is used the method of XML keys' vector matrix as windows, and vector product wavelet transform to multilevel decompose and refactor the XML streams series, that can fulfill real-time checking demand of XML quality, and ensure constraint, consist- ency and integrality. For even more adapting net load, it proposes a control strategy by weight and adaptive adjustment to ensure XML streams quality.

针对当前XML数据流质量检测存在的不足，提出构建XML键的矢量矩阵作为窗口，利用矢量积小波变换多级分解与重构XML数据流，再结合最小二乘支持向量机对XML数据流质量进行预测的一种方法，满足XML数据流质量重构时实时检测的要求，保证XML数据的约束性、一致性与完整性；为了更好的适应网络负载，采取加权与自适应窗口调整等调度策略充分保证XML数据流的质量检测。