查询词典 spring safety valve

Flap valve pin and WA44C Type Pound-Grade Balance Bellows Spring-Loaded Safety Valve valve shaft axial clearance between the bearing face not less than 0.25mm.

阀瓣轴销与阀体支承端面之间的轴向间隙不应小于0.25mm。

Because the valve seal is poor, the boiler will leak during operation, resulting in pot Twin spring type safety valve water temperature is warming up slowly, and thus a waste of energy.

因为安全阀密封性差，锅炉在运行过程中会漏气，造成锅内水温升温慢，从而浪费能源。

AQSIQ recently in Tianjin, Hebei, Shanghai, Jiangsu, Zhejiang, Anhui, Fujian, Henan and other 8 provinces, municipalities and 33 of the 33 production valve products for the Closed Spring Loaded Full Bore Type-High Pressure Safety Valve supervision and checking.

国家质检总局前不久对天津、河北、上海、江苏、浙江、安徽、福建、河南等8个省、直辖市33家企业生产的33种安全阀产品进行了监督抽查。

As the "Hydraulic safety Closed Spring Loaded Low Lift Type-High Pressure Safety Valve valve," has two levels pressure relief function and pressure from low to high pressure limiting function; with limited pressure relief and anti-corrosion properties of good stability and reliability advantages of the patented product may greatly enhance and expand power systems and hydraulic equipment hydraulic mine support equipment, quality and performance.

由于&气动液压安全阀&具备二个级别卸压功能和从低到超高压力的限压功能；具备限压卸压稳定可靠和防腐性能好的优点，本专利产品可极大地提升和拓展液压动力系统和液压设备矿井支护设备的品质和性能。

Recommended National Standards GB/T12243-2005 "spring load safety valve directly," provides a safety valve back seat pressure Automatic sludge-draining filter should be greater than 85% of the entire set pressure or 80% of the entire set pressure.

推荐性国家标准GB/T12243-2005《弹簧直接载荷式安全阀》规定，安全阀的回座压力应大于85%的整定压力或80%的整定压力。

Recommended National Standards GB/T12243-2005 "spring load safety valve directly," provides a safety valve back seat pressure should be greater than 85% of the entire set pressure or 80% of the entire set pressure.

推荐性国家标准GB/T12243-2005《弹簧直接载荷式安全阀》规定，安全阀的回座压力应大于85%的整定压力或80%的整定压力。

Recommended National Standards GB/T12243-2005 "spring load safety valve directly," provides a safety valve discharge pressure should not exceed 1.1 times the setting pressure or 1.2 times the setting pressure.

推荐性国家标准GB/T12243-2005《弹簧直接载荷式安全阀》规定，安全阀的排放压力应不超过1.1倍的整定压力或1.2倍的整定压力。

Recommended National Standards GB/T12243-2005 "spring load safety valve directly," provides a safety valve discharge coefficient should meet or exceed the nameplate specified value.

推荐性国家标准GB/T12243-2005《弹簧直接载荷式安全阀》规定，安全阀的排量系数应达到或超过铭牌规定值。

Regulating valve A42C Type Pound-Grade Low Lift Spring Loaded Safety Valve adjustment were tested hand wheel to full release and make valves were tested by examining the flow, measured by the pressure gauge the pressure relief valve in and out of the oil port, the difference shall be test valve pressure loss.

调节被试阀的调节手轮至完全松开，并使被试阀通过检验流量，由压力表测量溢流阀的进出油口压力，其差值即为被试阀的压力损失。

In addition to valve fully open position, the valve flap valve components and the gap between the inner wall of not less than for the cast iron 1 9mm, for the non-ferrous metal or stainless A44C Type Pound-Grade Full Lift Spring Loaded Safety Valve steel of not less than 9mm (not including brake locks and locking institutions).

除阀全开位置外，阀瓣组件与阀体内壁之间的间隙对于铸铁不应小于1 9mm，对于有色金属或不锈钢不应小于9mm(不包括制动锁和锁止机构)。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。