查询词典 spring back

Fill up the stability of direction of press press spring back for aggrandizement air, NIKE the company publishs section of new shoe of the 3rd season, roll out humorous mode air cushion , be just as increase like bedspring avoid shake protection holds trends of the body that have a shoe concurrently to stabilize.

为强化大气垫受压回弹方向的稳定性，NIKE公司发表第三季新鞋款，推出谐调式气垫，如同弹簧般增加避震保护兼具鞋身动态稳定。

Matrix nutrition earthen bowl is put all right at was being pressed on October 18 go up in seedbed, what 1 ～ 2cm stays between every nutrition earthen bowl is interstitial, press every nutrition earthen bowl next self-prossessed the scale of 1.6 times water calculates 1 ～ total water requirement, cent is irrigated 2 times, removed 1 ～ 2 hours, earthen bowl of the nutrition after watering will be very fast bibulous spring back, expand complete hind, wait for earthen bowl of the nutrition that plunge into thorn with taper iron needle or bamboo autograph, the examination expands whether completely loose, if hard core still needs to continue to water, until expand entirely...

基质营养钵于10月18日按行摆放在苗床上，每个营养钵之间留1～2cm的空隙，然后按每个营养钵自重1～1.6倍水的比例计算总需水量，分2次浇入，间隔1～2小时，浇水后营养钵会很快吸水回弹，膨胀完全后，用尖细的铁针或竹签等扎刺营养钵，检查是否完全膨胀疏松，如有硬芯仍需继续浇水，直到全部膨胀。。。

The simulation result indicated that it is feasible to predict spring-back curve based of cubic spline.

仿真结果表明基于三次样条来预测回弹曲线是可行的。

This paper makes an analysis of the kinematical rules and technical characteristics of movement-round-off spring back handspring and bent leg back flip with 2 twists in Yang Wei s vaulting horse,in order to provide the theoretical basis and technical parameter for its further development in China.

通过运动学分析揭示了我国优秀体操运动员杨威完成的跳马踺子后手翻屈体后空翻2周的运动学规律与技术特点，为我国运动员发展此类动作提供了理论依据和技术参数。

Caused by the brake disc brake on back wheel should not have four kinds of spaces possible: First, the foot brake 5 exhaust inlets, high pressure gas instinct Pai people the atmosphere, caused by gas-liquid master cylinder should not spring back to place, cause the system Oil will move the brake disc brake wheel cylinder piston top dead can not come back to places; are gas-liquid two disc brake master cylinder to the tubing plug, resulting in brake wheel cylinder piston can not come back to places; are three master cylinder of gas-liquid Can not spring back to their own spaces, brake fluid under high pressure gas, liquid should not return to the master cylinder reservoir chamber, resulting in brake wheel cylinder piston can not come back to places; are four wheel disc brake piston brake system because of moving fluid dirty or rusty Pistons Can not Back-bit card dead.

造成盘式制动器上的制动分泵不能回位有4种可能：一是脚制动阀5的排气口堵塞，高压气体本能排人大气，造成气液总泵的弹簧不能回位，导致制动油将盘式制动器的制动分泵活塞顶死而不能回位；二是气液总泵至盘式制动器的油管堵塞，造成制动分泵活塞不能回位；三是气液总泵的弹簧本身不能回位，制动液在高压气体作用下，不能回到气液总泵的储油室，从而造成制动分泵活塞不能回位；四是盘式制动器制动分泵活塞由于制动液太脏或活塞生锈卡死而不能回位。

The spring back in the distortion process was predicted by finite element method, and the predicted results were analyzed to find out the reason lead to spring back, and so as to precompensate the spring back.

利用有限元仿真对其变形过程中的回弹进行预测，并对预测结果进行研究，找出回弹根源，从而对其回弹进行预先补偿。

By analyzing the forming process to engine bracket lower plate , and introduced the design of bending die,some measures to control spring back were extracted, the spring back problem of engine bracket lower plate was solved.

通过对发动机支架下板成形工艺的分析及其弯曲模结构的介绍，总结了几种控制回弹的措施，解决了发动机支架下板回弹难以解决的问题。

Spring Airlines Company Limited, referred to as the "Spring Airlines" for the back passengers, will work with the Palme d'Or hotel Wenzhou Yi Jie cooperation, from now on (9) a period of three months from the date of the introduction of the "lucky Wenzhou Spring Airlines the "lottery class.

春秋航空有限公司（Spring Airlines Company Limited，简称&春秋航空&）为回馈旅客，将与温州意杰·金棕榈酒店合作，从今（9）日起推出为期三个多月的&春秋航空幸运温州行&客舱抽奖活动。

There are many problems in the carling forming and unloading processes such as expand and shrink of U section wall, the torsion of U section and the warp of carling head. These problems are concerned by the carling factories and do not solved for a long time. The mechanism of the carling forming and spring back is analyzed. The carling forming and spring back processes are simulated by KMAS software. The warp of carling underside is researched by half analytic and half experiment method and the best scheme is found by this method.

针对纵梁冲压成形及卸载后发生的U型截面侧壁的外扩、内缩、扭转以及纵向端头翘曲等问题，首先分析了纵梁的成形及回弹变形机理，利用仿真分析软件KMAS进行了数值模拟并采用半解析、半实验方法研究了纵梁底面翘曲，找出模具结构的最佳方案。

In addition, this paper also makes preliminary study on spring back of HSS plate forming, because the spring back defect in automobile panel forming is the most complex problem.

另外，基于大型汽车覆盖件成形生产中最为令人困惑的回弹问题，本论文还对高强度钢板成形后的回弹现象进行了初步的探讨。

In the United States, chronic alcoholism and hepatitis C are the most common ones.

在美国，慢性酒精中毒，肝炎是最常见的。

If you have any questions, you can contact me anytime.

如果有任何问题，你可以随时联系我。