查询词典 spline interpolation

Likewise,the axile potential and intensity of the system were calculated by Gauss elimination method and cubic spline interpolation.Furthermore,the electronic trajectory was traced by the changing steps Runge-Kutta method,the final size of e-beam about anode was true of demand.

在此基础上，通过Gauss消元法和三次样条插值法等解得了系统对称轴上电位分布以及内部场强分布，并利用四阶Runge-Kutta法追踪了电子从阴极开始到阳极入口处的运动轨迹且得到了合适的束斑大小。

Simplified the complex assembly access identification is simplified to the polygonal largest inscribed circle computation. Determined the pipe route by the spline interpolation whose nodes were the centers of polygonal largest inscribed circle list.

将复杂装配通路的识别简化为多边形最大内切圆求解；管道敷设路径则由若干典型装配通路横截面最大内切圆圆心插值曲线来确定；管道敷设路径的优化采用直线逼近曲线算法。

To improve the machining quality and the efficiency of curves, a novel Non-Uniform Rational B-Spline interpolation algorithm based on redundancy error and velocity smooth control was proposed.

为提高曲面加工的质量和效率，提出了一种基于冗余误差和速度平滑控制的非均匀有理B样条曲线插补算法。

This method requires less computation time than the B-spline interpolation method.

这种方法简单，所需的计算量小。

Simulation with OpenGL shows that parametric cubic spline interpolation method can solve the problem of eshoulder and neck deformation, make the mannequin more realistic,and the method is suitable for mannequin model simulation.

通过OpenGL模拟仿真表明，参数三次样条插值方法能够解决服装人台肩颈部的变形失真问题，使人台更具真实感，非常适合服装人台模型仿真。

This is the method of calculating it, and spline interpolation code, you can refer to.

详细说明：这是计算方法里面的，样条插值代码，大家可以参考一下。

Starting discussion on calibration points of Compensated Neutron Log,this paper proposes that spline interpolation, instead of conventional regression fitting,is used to build the response equation of CNL.

本文从对补偿中子测井实验刻度点的讨论出发，提出用样条插值方法而不是通常回归拟合方法来构造补偿中子响应方程。

The lattice was deformed as a particle system using advanced numerical methods, and the hairs were animated using quadratic B-Spline interpolation.

晶格被作为一个粒子系统采用数学方法变形，毛发采用2次B样条插值方法绘制。

To do this,a novel quintic spline interpolation and velocity profile algorithm are presented.

为适应高速高精加工，针对传统插补算法和速度控制方式在进给过程中存在柔性冲击的问题，提出了一种五次参数样条曲线插补方法及其速度生成算法。

This dissertation researches in the vibrant clipped data of a plane, proposes regression analysis, BP learning algorithm and cubic spline interpolation to forecast the clipped data.

以国产某型无人机空飞时振动传感器测得的振动削波数据为研究对象，选用回归分析法、BP神经网络法和三次样条插值法对削波数据进行预测恢复。

In the United States, chronic alcoholism and hepatitis C are the most common ones.

在美国，慢性酒精中毒，肝炎是最常见的。

If you have any questions, you can contact me anytime.

如果有任何问题，你可以随时联系我。