查询词典 spindle-legged

RESULTS: Cells were spindle shape before induction, obviously varied following preinduction, and then the body began contracted after being induced in the medium for 1 hour, with the presence of a few small orbicular-ovate or spindle cells. Following 24 hours of induction, about 60% cells became double pole, multipolar or cone shape, showing neuron-like structure.

结果：①诱导分化前呈梭形细胞，在加入预诱导培养基后未出现明显的形态变化，换用诱导培养基1 h，胞体开始收缩，出现少数较小的卵圆形或纺锤形细胞，诱导24 h后，约60%细胞变成双极形、多极形和锥形，出现类似神经元细胞的形态。

A person can place a drill in the drill chuck that is secured in the spindle of the drill press. They can then select the desired speed for rotation (commonly by switching belt pulleys), and activate the spindle. Then they manually pull on the quill lever to drive the drill into the workpiece being machined.

操作者可以将钻钻头装在钻夹中，钻夹固定在台钻的轴里；接着可以选择所需的转速（通常通过切换皮带改变主轴转速），并且启动主轴旋转，然后操作钻轴手柄，将钻头钻入被加工的工件。

Coolant Through Spindle with micro filter system, spindle pump and all the necessary plumbing.

通过主轴中心冷却系统包括微过滤系统，增压泵及所有必需的连接管材。

The design subjects include the selection and distribution of gear wheel, the design of spindle, and the guiding equipment and selection of the multiple spindle heads, etc.

因此本设计的重点是多轴箱的设计，设计内容包括齿轮分布与选用、轴的设计、多轴箱的选用、导向装置设计等。

The design of the device using NC Lathe CA6240 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with.

本设计利用数控装置对CA6240普通车床进行控制，主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴，通过变频器和齿轮变速箱实现分段无级变速；进给系统采用步进电机通过减速后驱动滚珠丝杠运动，在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠，在横向进给系统中通过二级齿轮减速驱动滚珠丝杠；刀架改为自动转位刀架从而实现自动换刀；通过MCS-51系列8051单片机对数据进行计算处理，由I/O接口输出步进脉冲信号控制进给速度和行程；为了保持切削螺纹的功能，要在主轴外端或其它适当部位装上脉冲发生器；将车床的手动尾座改造成为可控电动尾座。

Start from the performance of the spindle with! flat bottom and the innovation edge with the comparative analysis through the test data,introduction is made to the performance of the hydrokinetics bearing spindle with flat bottom .

从平底锭子的特点、性能及创新点入手，并通过测定数据进行对比分析，阐述了平底流体动压轴承锭子的特点，指出该锭子是一种高效平稳、低耗节能、低噪声的新一代锭子，是一种划时代的换代产品。

Firstly, the 3D solid model of the analyzed object is built directly in the FEM software ANSYS 8.0 without using other CAD software. The influence of the side sizes of solid elements on computing results and the influence of coupling ways between different parts on the modal parameters are researched by simply modeling. And a new connecting method about joints in ANSYS is proposed and applied to finite element modeling of the test-bed for spindle system. Furthermore, several different computing techniques for modal parameters extraction are compared in solving the finite element model of spindle system test-bed. Many modal solutions are also done to achieve the relationships between the whole or part stiffness value and computed modal parameters. The laws about joint rigid parameters" influences on modal parameters are discussed by means of altering their values for conjoint parts. And by changing local rigid parameter values, the different location selections" influence on computed modal parameters is also studied.

本文通过使用ANSYS 8.0软件直接建立研究对象的实体结构模型，而没有借助其他的CAD软件；通过构建简单的模型研究实体单元边长大小对计算结果的影响，部件之间不同的联结方式对模态参数的影响，探讨在ANSYS中实现结合部的方法，提出一种新的联结方法，并建立主轴系统试验台的有限元模型；对建立的主轴系统试验台有限元模型求解，比较几种不同模态提取方法；通过改变结合部联结单元的刚度参数进行的计算，寻找联结刚度对模态参数变化的影响规律；改变局部联结单元的刚度参数，研究刚度值位置差异对计算模态参数的影响。

The cutter location in NC generative ultrasonic grinding process for parallel ruled surface with cylindrical grinding wheel was analyzed,the structure of NC generative ultrasonic grinding device was introduced,the design of grinding spindle assembly and the spindle's driving scheme was also introduced,system hardware and software design had been finished.

分析了圆柱磨轮数控展成超声磨削平行直纹面时的刀具空间位置，介绍了数控展成超声磨削成形加工机床的总体结构，论述了磨轮主轴部件设计及主轴驱动方案，实现了主轴变频调速控制系统软硬件设计。

CNC face milling and drill centres hole machine （Referred to as CNC milling fight machine ）,machine is mainly used for shaft parts batch and mass production, miling shaft at both ends 、 drilled the centers hole and turning one end of cylindrical axis, configured SIEMENS 802C CNC system , is controled by three axis, that is, the left X-axis spindle box movement, Y Right-axis spindle movement, Z-axis hydraulic self-centering jig up and down movement, according to the procedure to complete part of the auto-processing, processing of high precision and high efficiency.

数控铣端面钻中心孔机床，机床主要用于轴类零件成批和大批量生产，铣削轴的两端面钻中心孔并可套车轴一端的外圆，配置SIEMENS 802C数控系统，三轴控制，即X轴左主轴箱运动，Y轴右主轴运动，Z轴液压自定心夹具上下运动，按程序完成零件的自动加工，加工精度高、效率高。

In this paper, the configuration of motorized spindle is studied and the procedure of direct torque control for motorized spindle is investigated, and the system principle sketch map is drawn.

结果 建立了高速电主轴直接转矩控制系统仿真模型，完成了仿真系统调节器及其参数设计，对系统的恒定负载和负载变化两种情况进行了仿真研究。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐