查询词典 spill box

Has: Blow-box tool kit sets; injection tool box sets, bubble shell tool sets, metal box tool kit tool kit.

有：吹塑盒工具套组套；注塑盒工具组套，泡壳工具组套，金属盒工具组套，工具包，。

Our company is a well-experienced and professional manufacturer in the field of wooden box,cigar box and jewelry box.

我们是一家拥有良好经验，专业生产木盒，雪茄盒和珠宝盒的公司。

The results show that the stress of clack box is lower than the yield limit of the material. The safety factor is between 1.8 and 3.2, and the distortion of clack box is in the permission scope. The static strength and stiffness satisfy the request, and the life of clack box exceeds 107, which meets the requirements.

研究结果表明，在3种载荷工况作用下阀箱应力均低于材料的屈服强度，其安全系数为1.8~3.2，且阀箱的变形在允许范围之内，阀箱静强度及刚度满足要求；阀箱疲劳寿命大于107，也满足要求。

Study is aimed at box threads of Φ177.8mm drill collar to analyze and calculate drill collar box thread with different stress-relief grooves using finite element method, the stress concentration of thread end of 3 types of box threads is gained under same boundary condition and load.

以177.8mm钻铤母螺纹接头作为研究对象，用有限元方法对加工有不同应力减轻槽的钻铤母螺纹接头进行了分析计算，得出了3种不同母螺纹结构在相同边界条件和载荷作用下螺纹消失端的应力集中情况。

When working on the Ex area, the first that contractor shall considered is the connection between couduits and connection between conduit with junction box, pull box. The connection between those part shall be kept a contiunous electricity. Secondly, when the cable connected to the pull box, ex-proof type connector shall be installed.

14.3.2.1 由于是在防爆区，因此电缆管的安装首先要考虑的因素之一是电缆管之间及电缆管与接线箱、穿线盒、电缆桥架之间的连接应保持良好的电气连续性并进行接地，此外，电缆管在与接线箱连接时，必须安装防爆密封接头。

But the steel box girder is typical space thin-walled bars, because of bending-torsion coupling and steel curved box bridge distribution of stress is relatively more complicated even under dead load, so it is necessary to distribute emulation analysis to the real stress of curved box bridge.

但是钢箱梁是典型的空间薄壁杆件，由于弯一扭耦合作用，曲线钢箱梁即使在恒载作用下其应力的分布也比较复杂，因此有必要对曲线钢箱梁实际的应力分布进行仿真分析。

Presenting the calculating method of the space displacement model of skewed box girder, whit main ideas of: dispersing the skewed box girder into some skewed beam segments and further dividing those segments into some plate pieces according to their forms; describing the displacement functions in the plane of plate piece by assuming that the space displacements of any point in the joint line between the plate pieces are described by using Hermite interpolation functions and that two displacements in the plane of plate piece are linear in the cross direction; Using Hermite interpolation functions to describe the bending the displacement of the unit length transverse frame cutting longitudinal from the skew box girder segment; Finally, describing the space displacements of a point in the plate pieces by two displacements in the plane of the plate and one bending displacement of plate.

提出了斜交箱形梁空间位移场的计算方法：将斜交箱形梁沿纵向离散为若干斜梁段单元，依据箱梁的构成进一步将斜梁段划分为若干板段子单元；各板段联结线上任意点的位移按Hermite函数插值，假定各板段的面内位移沿其宽度方向线性变化，以描述各板段面内位移；沿斜交箱梁段的纵向截取单位长度横截面框架，框架各杆件空间位移按Hermite函数插值，以描述各板段面外位移；板段内任意点的空间位移最终以2个面内位移和1个面外位移描述。

When you drag the dialog box, you can drag in accordance with your direction, adjusting the dialog box the location of all controls can also be adjusted according to the size of the dialog box controls the size.

详细说明：当你拖动对话框，可以根据你拖动的方向，调整对话框里所有控件的位置，也可以根据对话框的大小调整控件的大小。

Finally, introduce the design of the box which reception the receive system. the box wholly use steel board ,pass the press and bend procedure ,then compose a box connect with some boles.

最后介绍了乘载此接收系统的机箱的设计，机箱主要采用一般钢板，经过冲压、弯曲后成型，然后用螺钉连接。

The sequence （GenBank accession DQ77520） contained a novel promoter region with TATA box,CAAT box and CA2 box-like elements in the identical positions common to the eucaryote promoter sequence regions in comparison with the sequences in the GenBank.

对该产物测序并提交GenBank数据库（GenBank accession DQ677520），经序列比对分析，发现该序列具有真核启动子序列的基本结构特征，含有TATA盒、CAAT盒、GC盒等元件。

The work of this paper is as follows: 1. Looking back the progressing history of the linear motor, introducing the features of the elevator driven by linear induction motor, radicating the topic of this paper "the digital frequency variable control of the elevator bi-side direct driven by linear induction motor". The research of this paper covers the conventional VVVF control, space vector based VVVF control, vector control and DTC.

本文主要开展了以下几个方面的工作： 1 回顾了直线电机发展历史，电机的驱动技术演变，特别是针对直线电机的驱动，简要介绍了直线感应电机驱动电梯的优点和不同结构类型，对传统的v／f控制，基于空间矢量法的v／f控制，矢量控制，和基于电压空间矢量的直接转矩控制进行了比较，确立了本课题的研究主题：直线感应电机双边直推式驱动电梯的全数字变频控制。

The article combines with the treatment of a superficial civil air defense work to introduce how the grouting method to improve the performance of the backfill soil.

文章从治理漂浮人防工事的角度提出了注浆技术在改善回填土性质方面的应用，并详细阐述了注浆技术的施工流程。