查询词典 snack bar

The bar code image recognition program coded by VC++6.0 is compared with the experimently real-time processing system, and the results show mat the processing speed of the latter is very greater than the speed of the front Studies in the thesis promote the automatic identification of bar code image and its practicalization and present some ideas of how to improve the bar code image processing system based on DSP.

本论文的研究，为条码图像的自动识别和实用化做了一些促进工作，对基于DSP的条形码图像处理系统改进发展提出了自己的看法。

If there is joint on the back, in the lower right or fill a 20% discount after it has been causing wrinkles without distortion; vacuum packaging vacuum after the contents of the packin mouldedround radiofrequent nonanatomical tridimension on the surface, shape, surface roughness, would create a bar code reading of deformation cannot, therefore, be appropriate for the vacuum packing inner bag direct business card printing and membership card to make a bar code, you can increase the packin business card printing outside and membership card to make a bar code, and other graphics and text.

如背面中央有接缝，则印在右下方或印在填充后不起皱折、不变形处；真空包装抽真空后包装袋紧贴在内容物表面，呈不规则立体形状，表面不平整，会造成条形码变形不能识读，因此真空包装内袋不宜直接制卡和会员卡制作条形码，可增加一个外包装袋制卡和会员卡制作条形码及其他图文。

Refer to the impacting-echo technology, we impacted the apex of the steel bar and incepted the reflecting stress \\ave through the resonator that fixed on the apex of the steel bar, and the value of the consolidating wave speed was calculated based on the timeof stress wave transmitted and the length of the steel bar, so, identifying the reflecting signal is the key of the consolidating wave speed method.

借鉴于冲击回波技术，固结波速的测定方法是在钢筋测杆的出露端施加瞬态冲击载荷，由安设在测杆顶端的传感器接收反射应力波信号，根据应力波的走时和测杆的长度折算固结波速的大小，因此反射信号的识别是固结波速法检测混凝土强度的技术关键。

In this paper, some problems such as the length of the anchor bar, velocity of the anchor bar and the quality evaluation of the anchor bar are also discussed.

对锚杆检测工作中遇到的锚杆长度、杆体速度和锚杆质量分类等问题做初步探讨。

As to the mate lag problems in loom beat up mechanism,comparing traditional four bar linkages with quick return four bar linkages beat up mechanism,the latter can solve the lag problems effectively.A CAD method of designing the quickreturn four bar linkages beat up mechanism is pointed out,and the design mathematics model and the kinematic analysis model are also presented.

针对现有织机打纬机构和开口机构在运动配合上存在的滞后问题，比较了传统的四连杆打纬和具有急回特性的四连杆打纬机构，基于后者能有效地改善配合上的滞后问题，提出了精确设计具有急回特性的四连杆打纬机构的CAD方法，给出了设计的数学模型、机构运动分析的数学模型。

The Internet bar cooperates, cooperate with each Internet bar, pay a few fee, install the acquiescent and initiative page of the browser for insurance net, look for a 349 domestic Internet bars, the person that this gets online to the Internet bar more than 1, discharge also can be driven a few.

网吧合作，和各网吧合作，支付少量费用，把浏览器的默认起始页都设置为保险网，找个三五十家网吧，这到网吧上网的人一多，流量也会带动一些。

Bar code also known as line of bar code, and bar codes, it is a common commodity label can be said to futuresmarket.

条形码也称线条码和条码，它是一栽常用的商品包装标签，可以说是商品的身份证。

The test results demonstrated that the peeling with incisor bar could reduce green veneer curl-up ratio over 60% compared with the smooth roller bar, and generate more even veneer thickness and less veneer thickness variation than the smooth roller bar.

结果表明：采用柔化辊旋切的单板的湿单板卷曲率比光滑压辊下降了60%，单板厚度较均匀，厚度偏差较小；柔化辊与光滑压辊的最佳旋切设置完全不同。

The optimum lathe settings for incisor bar and for smooth roller bar were quite different, which indicate that the lathe settings have to be adjusted after changing bar from one to another.

柔化辊的最佳旋切设置为：旋刀倾角90.5°，垂直间隙9.84mm，水平间隙2.79mm；光滑压辊的最佳旋切设置为：旋切倾角88.5°，垂直间隙11.75mm，水平间隙2.54mm。

Microsoft, the master of the internet, exposes the file names in the blue bar on top screen, the address bar and the status bar.

微软，互联网的主导者，在屏幕上方的蓝色栏中暴露了文件名，地址栏和状态栏。

Dixie itself is a nickname for the American South.

Dixie 本身是美国南部的别称。

I think John Terry epitomises that and a big reaction is what we will be looking for.

而我认为特里就是这样一个典型，他正是我们期望看到的那个领秀。