查询词典 slot

Both repeaters are in this case, for example, so-called alternating slot repeaters.

例如，两个中继器在这种情况下，就是所谓的交替时隙中继器。

Buick could receive a rebadged Insignia to slot beneath the LaCrosse.

别克可以收到rebadged勋章插槽下方的君越。

The results show a reversed-flow region is formed at the tip of the pressure side due to the influence of the outside hot combustion gas and the pressure side tip thickness. The pressure gradient makes the coolant flow exit from the trailing edge slot first separates from the trailing edge cut-back, and then affected by the expansion wave, the coolant gas reattaches the cut-back of the trailing edge after passing a certain distance.

研究表明，由于外流和叶片叶盆尾缘厚度的影响，叶盆尾缘端部形成局部回流，叶片尾缘劈缝气体流出后受压力梯度的影响先抬起与叶背面分离，在流过一段距离后由于跨音速流膨胀波的作用，冷气流再次附着在叶背尾缘上。

The design of a large aperture slot antenna for harbor radars is studied in this paper.

本文仅就港口雷达大口径波导裂缝天线的设计进行探讨。

The cut-off valve with pilot valve without hand wheel, stem and lift nut inside will guide block and guide slot Butterfly Valves to guide sleeve, the disc-shaped disc to disc type bowl shape, and holes in the bottom of the flap valve to open, the valve cover of the original valve stem hole to hole diversion, because of increased pressure ring, ring, and the valve flap to class mortar, so that the flow passage separated the upper chamber cavity, external cavity, cavity, in the cavity and The external cavity increases with draft tube and stainless steel manual ball valve, flap valve in the cover plate and the center of the end of installing the spring, the upper flap valve install compression seal of the pressure ring, outside the cavity of the wall to open a Drainage holes.

带先导球阀的截止阀无手轮、阀杆和内升降螺母，将导向块与导向槽改为导向套，将盘形阀瓣改为类钵体形阀瓣，并在底部开阀瓣孔，电动蝶阀将阀盖原阀杆孔改为导流孔，因增加压环、密封圈和将阀瓣改为类钵体，使上通流腔分隔为上腔、外腔、内腔，在上腔与外腔的外部加设有导流管与不锈钢手动球阀，在盖板与阀瓣底的中心部加设弹簧，阀瓣上部加设压紧密封圈的压环，在外腔的壁上开有放水孔。

In order to solve this problem and dismantle the fuses automatically, the detonators are classified into three types, i. e. slot type, hole type, nut locking and smooth cylinder type. Three types of tools used to dismantle the fuses are designed, which are bit type, pin type and jaw type.

针对这一问题和引信自动分解的要求，将传爆管分为槽型、孔型、锁紧螺母和光滑圆柱面型等三种类型，相应地设计了刀片型、卡针型和卡爪型三种旋卸头，重点研究了卡爪型及其卡爪曲线设计计算方法。

As the crank rotates the slot at 3' moves up and down the fixed diaphragm in d, exactly as the pin 3 and block c in the last example.

作为曲柄旋转插槽3 '的动作向上和向下的固定膜片的D ，正是由于引脚3和C座，在过去的例子。

The utility model profiles is cross-section shaped that in the side,there is the lumen cross-section.vertical profiles of inter-connected connectors connects eucampia square plate-shaped nut screw connected to the bottom profile and the slot between the rectangular cross-section of the convex edge grip tightly, so to connect high strength, easy disassembly

本实用新型的型材是在侧面上有内腔横截面是工字型槽的型材，垂直连接的型材间有弯角连接件和方板形螺母用螺钉相连，可把型材槽底和槽口间的矩形截面的凸棱紧紧夹住，所以连接强度高，拆装方便

Color-coded slot, and then press firmly on each printhead to

码插槽，然后在完成安装之后用力按下每个打印头，以确保接

This system consists of a microprocessor-controlled 12-slot rack and a choice of two superb mic preamps, the Neve 1081 and Air Montserrat (from the vintage Air Montserrat console).

该系统由一个微处理器控制的12插槽机架和两个出色麦克风前放，1081的尼夫和空中蒙特塞拉特（从旧式空中蒙特塞拉特控制台）的选择。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。