查询词典 sliding

Sliding on an inclined plane, this cushion is moved

连续不断的碰撞一直到规定的次数。

Basing on the understanding for the development of inclinometer and people's higher requirements of the inclinometer technology, This subject invents a new type of inclinometer,that is, intelligent digital sliding inclinometer.

基于对测斜仪发展历程的了解和人们对测斜技术的更高要求，本课题研制发明了一种新型测斜仪，即智能数显滑动式测斜仪。

Its results are compared with drilling's results.Based on inclinometer's production curve,sliding surface and meachanism are concluded in a way,which provide important information for landslid's treatment.

根据测斜成果曲线，可以较好地对滑动面的分布情况、滑动机制作出某种程度的判断，为滑坡的治理设计提供重要的依据。

Firstly, the conception of networked control systems, introduction and content of networked control systems theory are introduced. Secondly, the network induced time delays of different topology structure are analyzed and then the corresponding plants are modeled. Based on the above, a compensation scheme for the transmitting time delay from controller to actuator is developed. And also a sliding mode controller that makes the system robust is designed.

首先，介绍了网络控制系统的概念和网络控制系统理论的发展概况、研究内容及现状；其次，对不同拓扑结构的网络控制系统的延时进行分析并引入了相应的系统模型：在此基础上，针对网络传输产生的控制器到执行器的延时问题，对不确定输入延时系统提出了一种补偿策略，设计了滑模控制器，使系统具有强鲁棒性。

To deal with the second type of variable speed system, a method which combines sliding mode decoupling control theory and Phase-Locked Loop technique is firstly applied to the induction motor's variable speed control.

针对第二类系统，本论文首次提出了将滑动模解耦控制理论与锁相环技术相结合的方案，应用于感应电机的调速控制系统。

Making use of states transformation, states feedback and the disturbance redefinition, this paper defines linear systems sliding mode disturbance attenuation problem Q 2, which can be resolved by solving Riccati inequation.

通过状态变换和状态反馈以及干扰重定义，提出了线性系统的滑模干扰抑制问题Q2。问题Q2 可以通过解Riccati不等式得以解决。

Errors should be induced in calculating horizontal seismic inertial force and anti-sliding moment according to vertical slice.

对边坡作用水平加速度时采用竖向条分的不合理性，提出了水平条分和竖向条分联合的方法进行改进。

Therefore, the stress and strain of a half infinite plane indented by a sliding spheric tip were calculated based on an elastic-linear strengthened plastic deformation model, making use of a commercial software.

选用20#钢、45#钢、T8钢3种材料作为研究对象，利用三维有限元法动态模拟刚性球形磨粒在弹-线塑性平板上的压入-划动过程，所用磨粒半径为0.15mm，试样尺寸为1.2mm×1.2mm×3.0mm，划动距离1.2mm；采用ANSYS/LS-DYNA软件对每种材料在压入深度0.01～0.10mm范围内进行10次动态模拟。

It can be concluded that the slipping of phase interfaces or the viscous sliding of grain boundary, dislocation's oscillation, the infinitesimal plastic deformation that was caused by the difference of elastic module and heat expansion coefficient between phases of the alloy yielded the damping of the alloys.

研究表明合金的阻尼是由合金晶界和相界面滑动、位错振荡以及各相的热膨胀系数和弹性模量间差造成的微塑性变形共同造成的。

It is indicated that the damping of the alloy is induced by phase interface slipping or grain boundary viscous sliding, the infinitesimal plastic deformation which is caused by the difference of elastic modules and heat expansion coefficients between phases of the alloy.

结果表明： ZA27-4%Si合金阻尼随频率增大而减小，随温度升高而增大，阻尼不随应变振幅的变化而变化； ZA27-4%Si合金室温阻尼为5.83×10-3，与ZA27合金阻尼相当； ZA27-4%Si合金的阻尼是由合金内部的晶界和相界面滑动、位错振动以及各相的热膨胀系数和弹性模量间差造成的微塑性变形共同造成的。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。