查询词典 sliding friction

Though it is a long history of the research on static friction, many problems, such as relationship between static friction and static contact time, the relationship between static friction and load, and the prediction of static friction coefficient have not yet fully studied.

虽然静摩擦的研究历史很悠久，但仍有一些问题没有解决，如静摩擦与静止接触时间的关系，静摩擦与载荷的关系，以及静摩擦系数的预测等问题。

Therefore, the torque required to open the gate valve required torque than the closure of large, in addition, for a pair of contact between the sealing surface, the Non Rising Stem Resilient Seated Gate Valves coefficient of static friction between them than the dynamic friction coefficient, to make them from the static state generate the relative movement is required to exert greater force to overcome the static friction; due to temperature changes, so that the sealing surface pressure between the larger, need to overcome the static friction force also will be bigger, so that when you open the valve on the stem nut on the sometimes increase the torque exerted a lot.

所以，开启闸阀所需的力矩比关闭闸阀所需的力矩大，此外，对于一对互相接触的密封面来说，它们之间的静摩擦系数也比动摩擦系数大，要使它们从静止状态产生相对运动，需施加较大的力以克服静摩擦力；由于温度变化，使密封面间的压力变大，需要克服的静摩擦力也随之变大，从而使开启闸阀时，对阀杆螺母上施加的力矩有时会增大很多。" Moment analysis of valve operation "是由中国闸阀网提供的国际阀门新闻，译文仅供参考。另外，中国闸阀网还提供相关产品搜索：闸阀型号、闸阀价格、闸阀技术、闸阀新闻、闸阀生产商等。

The results indicate that as the value of fractal dimension is increased, the interfacial static friction coefficient first increases and then decreases; the interfacial static friction coefficient decreases as the fractal roughness parameter increases; while the inter-facial static friction coefficient increases as the material property or total normal load increases; the curve of static friction coefficient versus dimensionless total normal load is convex when the fractal dimension becomes smaller or fractal roughness parameter is larger or material property becomes smaller.

研究结果表明：界面的静摩擦因数首先随分形维数的增加而增加，然后随分形维数的增加而减小；界面的静摩擦因数随分形粗糙度参数的增加而减小，但随材料特性的增加而增加，也随总法向载荷的增加而增加；当分形维数较小或分形粗糙度参数较大或材料特性较小时，静摩擦因数－量纲一的总法向载荷曲线为凸弧。

The friction performances of carbon face were investigated with an inertia friction tester.The torque curve of carbon face was ideal,the coefficient of static friction was lower than that of dynamic in 0.28 MPa,the friction coefficient of static and dynamic decreased with the braking pressure increasing.To the fiber face,the coefficient of dynamic fric...

结果表明：碳质层的摩擦力矩在制动初期上升较快，中间过渡区平稳，尾部翘起较小；在制动压力小于0.28 MPa时静摩擦系数小于动摩擦系数，且动、静摩擦系数均随制动压力增加而减小；相对纤维层而言，采用碳质层摩擦时摩擦力矩曲线形态更好，连续制动时摩擦系数波动较小，磨损率低且能够有效保护偶件，是1种静/动摩擦系数比较低且适用于高载荷工况条件下使用的摩擦材料。

The results show that when the porosity of sample was higher, compressure rate was higher and resilience rate was lower, however resilient rate of sample with higher porosity were increased notably when pressure was increased, and it tended to accord with of sample with lower porosity. The friction coefficient was higher when porosity of paper-based friction material was higher, and the friction coefficient tended to reduce and stabilize when braking pressure was increased. The friction coefficient of sample with high porosity tended to reduce and stabilize in continuous braking cycles.

结果表明：在相同载荷下，随着孔隙率增大，材料的压缩率增加而回弹率降低，随着载荷增加，高孔隙率材料的回弹率先明显增大，而后趋于稳定；在相同比压和转速下，孔隙率越高，材料的摩擦系数越大，随着比压增加，孔隙率高的材料摩擦系数逐渐降低，且不同孔隙率材料的摩擦系数逐渐趋于一致；在连续循环制动时，高孔隙率材料的摩擦系数逐渐降低并趋于稳定。

By friction round shape of the different levels can be divided into cylindrical friction wheel drive, cylindrical trough friction wheel drive, three kinds of cone friction wheel drive.

按摩擦轮形状的不同，可分为圆柱平摩擦轮传动、圆柱槽摩擦轮传动、圆锥摩擦轮传动三种。

It is shown that the friction force and bulkhead thrust are the main factors of shield thrust setting, while the friction between the cutterhead and soil is the main factors of cutterhead torque setting. Friction force between shield and soil would make front soil of shield upheave, and subsidence of surface soil is induced by ground loss when the friction force between the cutterhead and soil results in the surface settlement asymmetrical distribution.

通过计算发现，盾构施工中盾壳摩擦和正面推力是盾构推力设置的主要因素，而刀盘与土体摩擦是刀盘扭矩设置的主要因素，盾构前方土体隆起主要由盾壳摩擦引起，刀盘摩擦作用主要引起地表沉降的非对称分布，地表沉降主要由盾尾空隙产生。

Friction rubber draft gear, as one of high-capacity draft gears, is developed after friction steel spring draft gear. Rubber has energy absorption capability and non-linear rigidity capability, so the friction rubber draft gear's capacity is usually higher than the friction steel spring bumper.

摩擦式橡胶缓冲器是继摩擦式钢簧缓冲器之后开发的一种大容量缓冲器，这种缓冲器利用了橡胶自身具有吸收能量及非线性刚度的特性，因此其容量一般比摩擦式钢弹簧缓冲器高。

The static friction and kinetic friction of cylinder are tested. The mathematical model of friction is presented. Then author proposes the mechanical method to improve the friction character of cylinder.

第二章研究了气缸摩擦力的特性，对静/动摩擦力进行了全面的测试，提出了摩擦力数学模型，并提出了改善气缸摩擦力特性的机械措施。

The flume experiments of equilibrium concentration in water and slurry have been done to determine the function between the kinetic friction angle and internal friction angle. The equilibrium concentration of debris flow calculated by the function between the kinetic friction angle and internal friction angle is quite close the equilibrium concentration data of debris flow in field.

通过实验确定以颗粒浓度和颗粒最大体积浓度为主的动磨擦角与静磨擦角的函数关系式，以该关系式计算的泥石流运动的均衡浓度与泥石流原型资料很接近。

These rules reflect some inherent feature of self and nonself, and they are the basic detection criterion of GECISM.

这些规则反映了"自我"和"非我"的内在特征，是GECISM进行"非我"检测的判据。

Until today, the media from China and the outside world still uses the term "Post 89". Regardless to whether it is for commercial gimmick or convenience, everybody still remember "Post 89", a term which carries a strong Cantonese accent.

时至今日，国内外艺术媒体还是在沿用&后八九&这个称谓，不管当初是为了商业噱头还是容易上口好记，反正大家现在是记住了&后八九&这个广东口音很重的词。