查询词典 sliding friction

The effects of space of finsnumber of tube rows and relative humidity of incoming air on airside performance of wavy fin with hydrophilic coating under dehumidifying conditions were experimentally explored for seven wavy fin-and-tube heat exchangers with hydrophilic coating. The Colburn factor and the Fanning friction were applied to describe airside heat transfer and friction characteristicsrespectively.

为了确定翅片间距、管排数和入口空气相对湿度等参数对析湿工况下带亲水层波纹翅片空气侧特性的影响，对7个带亲水层的波纹翅片管换热器进行了试验研究，并分别以Colburn换热因子和Fanning摩擦因子来反映空气侧换热和压降特性。

Generally speaking,"cold-water the effect of friction than the" dry cloth friction is better.

一般来说，"冷水磨擦的效果比"干布磨擦要好一些。

Close the valve, the need to open and close with the Coma Berenices two pieces of the sealing surface of the seal formed between certain specific pressure, while also overcoming the stem and the packing between the stem and the nut thread between the stem end bearing at and other friction parts of the friction, and therefore must apply the closing force and closing a certain moment, the valve in the open and close the process, the required hoisting hoisting force and moment of change, and its maximum is close to the final instant or open the initial transient.

关闭阀门时，需要使启闭件与发座两密封面间形成一定的密封比压，同时还要克服阀杆与填料之间、阀杆与螺母的螺纹之间、阀杆端部支承处及其他磨擦部位的摩擦力，因而必须施加一定的关闭力和关闭力矩，阀门在启闭过程中，所需要的启闭力和启闭力矩是变化的，其最大值是在关闭的最终瞬时或开启的最初瞬时。

Close the valve, the need to open and close with the Coma Berenices two pieces of the sealing surface of the seal formed between certain specific pressure, while also overcoming the stem and the packing between the stem and the nut thread Automatic Control Valves between the stem end bearing at and other friction parts of the friction, and therefore must apply the closing force and closing a certain moment, the valve in the open and close the process, the required hoisting hoisting force and moment of change, and its maximum is close to the final instant or open the initial transient.

关闭阀门时，需要使启闭件与发座两密封面间形成一定的密封比压，同时还要克服阀杆与填料之间、阀杆与螺母的螺纹之间、阀杆端部支承处及其他磨擦部位的摩擦力，因而必须施加一定的关闭力和关闭力矩，阀门在启闭过程中，所需要的启闭力和启闭力矩是变化的，其最大值是在关闭的最终瞬时或开启的最初瞬时。

Close discharge valve, the need to open and close with the Coma Berenices two pieces formed between the sealing suce sealing certain specific pressure, while also overcoming the stem and the packing between the stem and the nut thread between the stem end Department and other friction parts bearing friction, and must exert a certain degree of closing force and closing moments, PUMP CONTROL VALVE EN700X the valve in the open and close the process, the required hoisting hoisting force and torque is the change, Its maximum is in the closed or open end of the initial transient instantaneous.

关闭放料阀门时，需要使启闭件与发座两密封面间形成一定的密封比压，同时还要克服阀杆与填料之间、阀杆与螺母的螺纹之间、阀杆端部支承处及其他磨擦部位的摩擦力，因而必须施加一定的关闭力和关闭力矩，阀门在启闭过程中，所需要的启闭力和启闭力矩是变化的，其最大值是在关闭的最终瞬时或开启的最初瞬时。

The results indicate that the result of local Coulomb friction model and nonlocal friction model is not too distinctive.

研究结果表明：不考虑表面微凸的情况，局部库仑摩擦模型与非局部摩擦模型的结果差别不大。

Find out main friction again --Cylinder block and mixing the friction of the oil one, improve.

并对其主要摩擦——缸体与配油盘的摩擦，进行了结构改进。

The concept of a shroud dry friction damping factor is presented to measure dry friction damping on shroud interface.

提出用阻尼因子的概念解决关于凸肩干摩擦阻尼大小的度量问题。

To study the dynamic response performance of reinforced concrete frame structure with friction energy dissipation braces,the element stiffness and mechanics model of the element of friction energy dissipation device and the element of frame bar are analyzed.

为研究钢筋砼摩擦耗能支撑框架结构的动力反应性能，对其中的摩擦耗能器单元和框架杆单元的单元刚度和力学模型做了分析。

The shroud dry friction damping factor is a dimensionless quantity which can be defined as the ratio of the sum of work done per cycle of vibration by all dry friction force at shroud interface to the peak strain energy of corresponding blades under the resonance condition.

干摩擦阻尼因子是一个无量纲量，它被定义为：在共振条件下，所有的凸肩干摩擦力在振动一周内所做功之和与对应叶片系统峰值弹性变形能之比。

Objective To investigate the relationship between ovum fertilization rate and sperm morphology, acrosome reaction in IVF and to explore the influence of parameters of sperm on fertilization rate.

目的 研究体外受精(in vitro fertilization，IVF)中精子形态、顶体反应与卵子受精率之间的关系，分析精子各参数在IVF受精率方面的参考意义。

A: I hear Mr. White wants to run for the Presidency!

我听说怀特先生要参加总统竞选！