查询词典 slide guide

Two elongated guide members each have a rectangular slot which slidingly receives the edge of the slide plate.

两种细长的引导会员都有一个矩形槽，slidingly接收板的边缘。

Finished oil to slide back and forth rolling about in the guide this time to be loaded on rail times should first pay attention to when you do not install the first fixed rail, take the fixed screw fitted well to keep level in the belt and slip block is fixed, then install a good lens, dimming what avenue is finished X's whereabouts.

上完油在让滑块在导轨来回滚动一下，这时须次先把导轨装上，注意装导轨时不要先固定，要把固定钉全部装好，保持水平，在把皮带与滑块固定，再把透镜装好，调光一下X去向的去路完毕。

FLOAT PNEUMATIC CLAMP: The work piece is held in place by float pneumatic clamp with large holding forcestable feeding characteristics to the X-slide. The integrated swallowtail type carriage is high in rigidity. The clamp is easy to movethe slides run on hardened precision linear guide waysare driven by AC-servo motors.

浮动式气动夹钳：强大的夹持力保证加工板材在X滑架上稳定地进给，全燕尾型滑架完善的刚性使夹钳很容易地在伺服电机的驱动下沿硬化的高精度线性导轨上平稳精确运行。

A simple detection system which is composed of displacement sensor, linear slide block and guide track was designed using automatic checkout method aiming at the measurement requirement of some type projectile equipment.

针对某型炮弹装备的测试需求，采用自动检测方法，设计了一套结构简单的位移传感器、直线滑块和导轨组合的检测系统。

First to analysis original data, including the properties of the material and technological characteristics of the plastic part, then decide the divide surface of cavity and the arrange way of mold cavity, designing the side take out core outfit and guide runner and slide block, still carried on the calculation towards modeling part, cavity deep and thick, hot up and cooling, at last, check the data of injection molding machine.

首先分析原始资料，包括塑件材料的性能和结构工艺特点，然后确定分型面和型腔排列方式，接着设计侧抽芯机构以及导滑槽和滑块，还对成型零件、型腔壁厚、加热和冷却等进行了计算，最后对注塑机进行校核。

First to analysis original data, then decide the divide surface of cavity and the arrange way of mold cavity , designing the side take out core outfit and guide runner and slide block , still carried on the calculation towards modeling part, cavity deep and thick, hot up and cooling, at last ,check the data of injection molding machine.

首先分析原始资料，然后确定分型面和型腔排列方式，接着设计侧抽芯机构以及导滑槽和滑块，还对成型零件、型腔壁厚、加热和冷却等进行了计算，最后对注塑机进行校核。

First to analysis original data, including the properties of the material and technological characteristics of the plastic part, then decide the divide surface of cavity and the arrange way of mold cavity, designing the side take out core outfit and guide runner and slide block, still ca

首先分析原始资料，包括塑件材料的性能和结构工艺特点，然后确定分型面和型腔排列方式，接着设计侧抽芯机构以及导滑槽和滑块，还对成型零件、型腔壁厚、加热和冷却等进行了计算，最后对注塑机进行校核。

BALL SCREW; LINEAR GUIDE WAY; SUPPORT UNIT; SLIDE SHAFT;...

滚珠螺杆；线性滑轨；支撑座；心轴；。。。

Linear shaft, bearing, guide, joint bearing, slide unit, ball screw, machinery parts...

直线轴，轴承，导轨，滚珠丝杠，关节轴承，滑动单元，机床附件等

MAIN PRODUCTS:; LINEAR MOTION ,LINEAR GUIDE ,SLIDE BEARING ,MICRO STAGE ,BALL SCREW ,SUJ2 SHAFT ,COUPLING ,CROSSED ROLLER WAY ,BEARING ,OILLES BUSH......

线性滑轨。滚珠螺杆。直线轴承。精密轴心。直线滑台之件代理销售；本公司从事精密传动元如线性滑轨。滚珠。。。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。